Question about 2003 Honda Accord

Open Question

How to remove intake manifold on 03 honda accord to replace starter

How to remove intake to get at the starter motor

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: replacing a 97 honda accord starter

i haven't fixed the problem but I don't have any money to pay for a plan on here. thank you anyway.

Posted on Jan 15, 2009

Ad
philschneide
  • 448 Answers

SOURCE: locating the starter motor on a 2004 honda accord

Disconnect the negative battery cable. Disconnect the positive battery cable (if you have an anti-theft audio system, make sure you have the code).
Drain the cooling system. Remove the intake manifold ( not a real easy task).
Disconnect the starter cable from the B terminal on the solenoid. Disconnect the BLK/WHT wire from the S terminal.
Remove the harness clamp. Remove the harness holder.
Remove the starter retaining bolts. Remove the starter from the vehicle.
d6afbbe.gif
Hope this helps you find it.

Posted on Nov 18, 2009

66 chrgr
  • 1011 Answers

SOURCE: Cost to replace blower motor on Honda Accord?

The part from the dealer is $180.65 ,labor is .5 hours about $50. If you go to a independent shop the cost should be less:)

Posted on Nov 24, 2009

  • 819 Answers

SOURCE: how to remove starter solenoid from 1998 honda accord LX 4cyl?

the starter solenoid is integral to the starter.

Posted on Dec 26, 2009

  • 25 Answers

SOURCE: blower motor 1991 honda accord ex

the blower motor is located behind and under the glove box. its held to the blower housing by three screws. remove the three screws and the motor will slide down and towards you. to test the motor. apply power to the yelllow/black wire and ground to the blue/red wire. the motor should run. if not you prob have a faulty power resistor. 0881be0.jpg

Posted on Mar 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to locate and remove


According with your engine, select the right procedure:

REMOVAL & INSTALLATION

On all engines except the 2UZ-FE, the starter is external, mounted in a conventional manner, alongside the engine block. One the 2UZ-FE, however, the starter is mounted in the 'V' of the engine, between the cylinder head banks. The entire intake manifold assembly must be removed to access the starter motor and solenoid. (Toyota calls the solenoid a "magnetic switch.")
Except 2UZ-FE Engine
5_3_2012_1_13_25_pm.jpg

Fig. Unfasten the starter mounting bolts ...

5_3_2012_1_13_56_pm.jpg
Fig. ...then pull the starter toward the front of the vehicle to remove it (other components removed for clarity)
Disconnect the negative battery cable.Remove the nut and disconnect the battery cable from the magnetic switch on the starter motor.Detach the remaining electrical connections at the starter.Remove the nuts and/or bolts securing the starter to the bell housing, and then pull the starter toward the front of the vehicle to remove.
To install:
Insert the starter into the bell housing being sure that the starter drive teeth are engaged with the flywheel teeth, NOT jammed against the flywheel.Tighten the attaching hardware to 29 ft. lbs. (39 Nm) and replace all electrical connections.


5_3_2012_1_14_42_pm.jpg
Fig. Exploded view of a common starter mounting found on Toyota trucks
Connect the positive battery cable (starter wire) to the starter.Connect the negative battery cable.


2UZ-FE Engine

5_3_2012_1_15_21_pm.gif
Fig. The starter motor on this 2UZ-FE engine is installed under the intake manifold between the cylinder heads, making it a lengthy procedure to perform
Disconnect the negative battery cable.Remove the cosmetic/acoustic engine cover.Disconnect the accelerator cable and intake air connector.Remove the intake manifold assembly. For additional information, please refer to the following topic(s): Engine Mechanical, Intake Manifold.Remove the two bolts holding the starter motor to the engine block and lift the starter away from the block.Detach the electrical connectors from the starter and remove the starter from the vehicle.
To install:
Installation is the reverse of the removal procedure. Make sure all electrical connections are tight and that the harness is secure.Install the starter and torque the two bolts to 29 ft. lbs. (39 Nm).Install the intake manifold.Connect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.
Thank you for using FixYa, have a nice day.

May 03, 2012 | 2000 Toyota Tundra

2 Answers

On a 1998 Oldsmobile Aurora, where is the starter located? Thank you in advance, D-For


IF YOU DONT SEE STARTER UNDERNEATH CAR NEAR FLY WHEEL AND YOU HAVE THE 4.0L ENGINE STARTER LOCATED UNDER THE INTAKE MANIFOLD JUST LIKE THE 4.6L ENGINES IN CADILLACS.YOU HAVE TO REMOVE INTAKE TO REPLACE STARTER.

Mar 04, 2011 | 1998 Oldsmobile Aurora

1 Answer

How do you replace the starter on a 2004 Honda Element


Removing the starter unit on a first or second generation element is the same process.
There is also another way to remove the starter unit without removing the intake manifold like many other people post out there.
I am a Honda certified technician and always find ways to speed up my flat rate time when working on various models.
The process I used was faster for me, this may not be helpful or easier for others, based on skill level but some people would rather just remove the intake manifold and access the starter right underneath.
Here is how I removed the starter on a 2004 Honda Element without removing the Intake Manifold.

I first removed the serpt belt and then un bolted the powersteering pump and set it aside. I did not have to disconnect any hoses at all.

Next step, I unplugged the knock sensor harness and set it a side.

Next, I used a 3/8 12in extention and a 14mm wobble socket and reached down to unbolt the starter's upper mounting bolt.

Next few steps are underneath the vehicle.

The next step for me was to remove the front lower splash guard.

Once removed, there was a bracket directly in front of the starter that I had to remove in order to ease the aid of removing the starter unit.

The next step for me was to remove the starter's lower mounting bolt.

At this point I was able to pull the starter away from the transmission and twist it around to access and remove the blade harness and 12mm power/charge harness.

installation is reverse of removal.

This process was eaiser for me since I had always removed the intake manifold on the Element, CR-V and 4cylndr Accords.

I was trying to think outside the box and this process worked out fine for my solution.

Sep 18, 2010 | 2004 Honda Element

1 Answer

Replace starter on 2003 Honda Accord w/4 cylinder. Steps to take to remove and install new starter.


disconnect the cable to the battery........there is 3 bolt holding the starter to the engine/transmission housing. You may need to remove the air intake manifold to gain access to the work area.

Mar 20, 2010 | 2003 Honda Accord

1 Answer

Replacing starter for 1991 Honda accord lx with pics


If you want to change the starter motor, first disconnect the positive cable to the battery. Then under the intake manifold on the passenger side and between the engine and the firewall you should see the starter motor. It has a large cable that comes directly from the battery and a small wire that comes from the ignition. Disconnect both of them and then there should be two bolts that thread into the engine block, one on the top and the other one on the bottom. remove those and the started should be free. Replace in reverse.

Jan 11, 2010 | 1991 Honda Accord

1 Answer

Locating the starter motor on a 2004 honda accord


Disconnect the negative battery cable. Disconnect the positive battery cable (if you have an anti-theft audio system, make sure you have the code).
Drain the cooling system. Remove the intake manifold ( not a real easy task).
Disconnect the starter cable from the B terminal on the solenoid. Disconnect the BLK/WHT wire from the S terminal.
Remove the harness clamp. Remove the harness holder.
Remove the starter retaining bolts. Remove the starter from the vehicle.
d6afbbe.gif
Hope this helps you find it.

Nov 18, 2009 | 2004 Honda Accord

3 Answers

Starter for 2004 honda accord


Is this for a 4 or 6 cylinder engine?

If it is for the 4 cylinder, it's not that easy as the intake manifiold needs to be removed before the starter can be removed as the starter is under the intake manifold. Once the manifold is removed then it's a matter of a couple bolts and connections. It's not that quick a job.

Aug 19, 2009 | 2004 Honda Accord

2 Answers

Where is the starter located in a 2004 honda accord?


i havnt worked on a 2004 but all the hondas i worked on the starter was on top of the trans runing inline with the valve cover on the 4 cyl i dont know what motor you have hope this helps some

Aug 18, 2009 | 2004 Honda Accord

1 Answer

Replace starter


96 probe, 2.0L 4 cylinder. Should be similar to 626 I think.

Starter Motor
Removal


Exploded View of the Starter Motor Mounting Components




  1. stu~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When servicing the starter motor or performing other underhood work in the vicinity of the starter motor (11002), be aware that the heavy gauge battery input lead at the starter solenoid is "electrically hot" at all times. A protective cap or boot is provided over this terminal (B-terminal) on all carlines and must be replaced after servicing. Be sure to disconnect the battery ground cable before servicing the starter motor.
    Disconnect the battery ground cable (14301).
  1. Remove the air cleaner (ACL) and the air cleaner to intake manifold tube (9B697). Refer to Section 03-12A for the procedures.
  1. Remove the two upper starter motor bolts.




  1. Raise and support the vehicle.
  1. Remove the intake manifold support bolts and the intake manifold support (9J444).




  1. Disconnect the S-terminal wire.
  1. Remove the B-terminal wire nut and disconnect the B-terminal wire.
  1. Remove the lower starter motor bolt.
  1. Remove the starter motor.

Aug 10, 2009 | 1995 Mazda 626

2 Answers

Removing starter


It's not that easy. Yes, 2 bolts hold the starter down but you have to remove the whole intake manifold to access the starter to remove it.

May 30, 2009 | 2003 Honda Accord

Not finding what you are looking for?
2003 Honda Accord Logo

Related Topics:

393 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...