Question about 1992 Toyota Pickup

1 Answer

I have a 1992 Toyota pickup 4x4 3.0v6 this morning I started it as normal shifted from 1st to 2nd and it started to sputter really bad I pushed the clutch in and reved it up seemed to be ok so I let out the clutch and it did it again and stalled I tried to start it to the point where my battery started to go dead so I replace the distributer cap and button still no start I checked for spark comming from my coil it's good called an auto parts store to see about a crank shaft sensor apparently this truck doesn't have one also checked fuel and it's ok what else is possible to check

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 108 Answers

Your transmission and spark plugs

Posted on Apr 19, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 12 Answers

SOURCE: 89 toyota pickup, 4x4 3.0

More than likely either the ignition control module, the stator or the pick-up located in the distributor.

Posted on Dec 16, 2008

  • 19 Answers

SOURCE: toyota seinna po440, po441, po446

you have to understand that there is a leak in the system other than the gas cap for the evaporative system. The system needs to be professionally closed, and smoke introduced into to find the leak, and a through component check, eg.. purge valve vapor canister vent solenoid all functioning correctly

Posted on Sep 01, 2009

  • 714 Answers

SOURCE: 1986 toyota truck 22r fuel injected. runs to rich

check for a vacumn leak, my buddy has a 96 dually that did that,found out it was his temp sensor to the computor,was showing a negative # when i tested it,he replaced it and it fixed everything! He couldn't believe it LOL

Posted on Jan 11, 2010

  • 1374 Answers

SOURCE: i need a diagram of a 1996 toyota camry automatic

To play it safe have the TPS checked out by another repair shop .If they say its ok then its the shift solenoids.

Posted on Jul 19, 2010

airjer995
  • 5332 Answers

SOURCE: 1993 Toyota camry will not start

Check to see how much spark you have. Spark should jump at least a 3/4" inch gap. If it only jumps an eighth to a quarter inch or less than you have weak spark. If the coil is external replace it if the coil is inside the distributor replace the distributor. I almost guarantee this is a week spark issue.

Posted on Aug 07, 2012

Testimonial: "Jeremy was on the right track with the weak ignition since I did find a bad rotor with carbon tracking and a crack in it."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 toyota Camry manual hard shifting from 1st to 2nd gear


With the engine off see if the shift between 1st to 2nd feel,s free if not it could be the cable check the clutch is disengageing all the way it should go into reverse without crunching,other then that it could be a synchro ring worn check that the gearbox has the right oil in it.

Dec 20, 2015 | 2008 Toyota Camry

1 Answer

A hard shift between 1st and 2nd gear?


Most likely a solenoid on the valve body. It is just a coil that when energized pulls in metal rods, some push. When most coils start breaking down, they only act up when hot. Could also be the valves themselves. Also a bad seal. Ask friends for a good transmission shop. Some one that won't tell you a rebuild and only change a valve solenoid.

Feb 10, 2015 | 2005 Kia Spectra EX

1 Answer

I have an 80 series landcruiser with A442F transmission, built 1993. It will not select 1st gear or overdrive. It takes off in 2nd and shifts to 3rd normally, 1st gear can be selected manually and changes...


It seems like your "2nd start" button is turned on. The 80 series LC has a button next to the shifter which allows it to start in 2nd gear. If the button is not engaged then there could be a problem with the circuit, but that is not common

Nov 01, 2010 | 1994 Toyota Land Cruiser

1 Answer

93 toyota pickup. 4 cylinder, 5 speed manual 98k. ...


possible selector linkage adjustment , loose or shifted

Jul 02, 2017 | Cars & Trucks

3 Answers

After 20 miles of driving it shifts late and hard from 1st to 2nd


many things can cuase this, the first thing to do is have the computer scaned, there should be codes it there, these codes will give a general idea of the problem. you should also check the trany fluid level,(engine warm,in park, level ground). there may be a few things to check, the distributor cap and rotor, also the wires. you may have weak fuel preasure,or even a bad module, so start by having the codes pulled and will go from there,also it doesnt start now,check the fuel preasure and also check for spark at the plugs.

Mar 14, 2010 | 1991 Oldsmobile Custom Cruiser

1 Answer

5 sp man trans. when accelerating, trans hangs up


sounds like you have a worn syncronizer. unless it gets really bad, you can keep driving like that, be gentle with those shifts and you shouldnt have any problems. changing the fluid may help prolong the life. if it gets bad, the transmission will have to be rebuilt.

Mar 13, 2010 | 1995 Toyota Tercel

1 Answer

Hydraulic clutch grinding from 1st to 2nd - Toyota 1985 Pickup


Yes, your clutch might be worn and/or out of adjustment or the trans is worn. Your clutch may be fine also. Toyota's have a problem with there shifter bushings and seats. They brake and crack also causing shifting problems. And some times only one gear depending on the condition.If yours is broken,crack or damaged, you can find the parts from Toyota and there a whole lot cheaper than a clutch. Also I recommend adjusting the clutch if possible. Not all are adjustable. Check your clutch fluid.


a87388d.jpg

Mar 24, 2009 | 1985 Toyota Pickup

2 Answers

97 Toyota LC. Prado TZ . Auto- Transmission Oil change.


you are suppose to use T-IV ATF in toyotas or they will not shift correctly.

Feb 18, 2009 | 1997 Toyota Land Cruiser

Not finding what you are looking for?
1992 Toyota Pickup Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...