Question about 2004 Acura TL

Open Question

How to replace o2 sensor in 04 acura tl - 2004 Acura TL

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 8 Answers

SOURCE: 2005 Acura tl brake replacement

The Brembos that come on Type S/Manual models wear fast. I've changed them at 20,000 miles. They are expensive also.

Non-Type S/Manual models I have seen go 80,000 miles. The biggest factor on brake wear is how the vehicle is driven.

At 50,000 miles I would have them inspected. Depending on where you go, make sure you get an accurate measurement of both pads (inboard and outboard). 2mm is the service limit and about that time the indicators start making noise, but not always. Most indepent shops are going to sell you brake pads at 4mm. That's another 10,000 miles at least you could have driven on them.

Never replace just the brake pads, resurface or replace the rotors. The uneven surfaces of the rotor will cause your new pads to wear incorrectly and possibly cause brake noise. Most aftermarket pads will cause a squeel.

Posted on Sep 21, 2008

  • 4 Answers

SOURCE: trying to replace a front headlight bulb on 2001 acura 3.2 TL

Look for the end of the wire retainer clip. Unhook it and lift it up. Remember not to touch the bulb. But if you do, just clean it with a bit of alcohol.

btw - Here's a bit of info from a previous post of mine...
The low beams consist of three parts. The bulb, inverter/ballast and the ignitor. The bulbs usually start to loose their color long before they burn out. The inverters/ballasts either go out after a while or take a while to start up.

Before you spend money on a new bulb, try swapping it with the one on the other side. You'll need a security torx screwdriver to get the covers off of the back of the lights. Don't touch the glass bulbs. If you do, just clean them with a bit of alcohol.

If the problem stays on that side, try swapping the ignitors. They're mounted inside the black covers.

If the problem is still on that side you've got a bad inverter. They're mounted on the bottom of the headlight assembly. You'll need to remove the front bumper and remove the headlight assembly to get to it. (I recommend you take pictures as you remove things so can put them back together correctly.)

Posted on Jan 05, 2009

  • 840 Answers

SOURCE: 04 acura tl serpentine belt diagram

there should be a belt diagram from a label either on underside of hood or on radiator support. That should help if you can do it yourself.

Posted on Jan 24, 2009

masterraphie
  • 41 Answers

SOURCE: starter replacement on acura 2000 TL 3.2

This starter can be changed without disassembling the top of the engine on the 2.5 with automatic transmission. You will need a 10mm, 14 mm, 17mm, and a 9mm wrench. First with any electrical repair disconnect the battery at the negative terminal. The starter is on the driver's side close to the firewall below the intake manifold. Remove the transmission dip stick so you don't ruin it, then look and study the starter itself. You will notice the starter drive housing with a top and bottom bolt. The top bolt is a 14mm and the bottom a 17mm, loosen both a half turn. Remove the top 14mm bolt first, then the bottom 17mm, this will allow you to pull the starter out of the bell housing. With some angling and no brackets holding the back of the starter you should be able to pull it out enough to disconnect the positive wire and 9mm nut from the soleniod. Disconnect the starter ignition small wire by pulling it off it's connector. Now just pull it out of the engine and fender void and you've got it, saving about a hundred and fifty dollars of labor. Take it to the parts house and match it up with a well made remanufactured or new starter. Reverse the proceedure, hook up the battery.

Posted on Mar 19, 2009

  • 383 Answers

SOURCE: Where is the starter on a 1996 Acura 3.2 TL? On a

grantgga2: I don't think this is one you are going to want to try to change out.
It entails having to remove the left axle and part of the exhaust pipe to gain access to the starter. At that point, you have one bolt which goes in at the bottom from the starter side and bolts to the engine. The other bolt passes through the trans axle housing and bolts into the starter, pulling it up to the engine.
SCARED YA HUH? I'D SAY FROM A 1-10 FOR A WEEK END WARRIOR, IT WOULD BE ABOUT A 6.
Was I helpful?

Posted on May 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the o2 sensors on a 2000 Acura TL 3.2


usually located in the exhaust system (pipes) or manifold

Mar 02, 2017 | Acura Cars & Trucks

1 Answer

How do I know my O2 sensors are bad in my 2005 acura tl?


The sensors before the catalytic convertor can affect drivability. If they are failing, a code will set in the PCM and turn on the check engine light.

Jul 04, 2014 | 2005 Acura TL

1 Answer

P0134 sensor location


O2 sensor no activity bank one sensor one This is the first sensor in the exhaust system on the # 1 cylinder side on engine usually in exhaust manifold.

May 01, 2014 | 2005 Acura TL Automatic

1 Answer

1996 Acura TL check engine light on sets these codes po155, p0141,p0135 how do I fix it?


Okay, so usually when there are a large number of codes that show up at one time they are usually related, so one problem could cause multiple codes to appear. Here is a link to a trouble code reference sheet for the 96 - 98 Acura TL Acura 9698 3 2TL Trouble Code Info

From this sheet we can see that your issues all relate to your o2 sensor heater circuit, so the first step would be to check all your fuses, the problem could be as easy as your o2 heater circuit fuse is blown. next i would check the connections to the o2 sensors themselves, make sure you have good connections and clean the connections with some di-electric grease which you can pick up at any autostore and spray it in both connectors (the wiring harness for the car and the connector attached to the o2 sensor) let them dry then reattach them. if this does not fix the problem sadly you might have to start replacing the o2 sensors. Good Luck

Apr 25, 2014 | Acura TL Cars & Trucks

1 Answer

Im having a code P0420. Is this an O2 Sensor and if so how do I know if its before or after the cat converter?


DTC P0420: Catalytic System Efficiency Below Threshold
You will have to replace the catalytic converter nearest the firewall.

Aug 25, 2013 | 2000 Acura TL

1 Answer

Which O2 sensor is bad with a po 151 code for the check engine light?


This is a bank 2, sensor 1 code, which means the computer is picking up a problem with the O2 sensor that is located before the catalytic converter on the front bank of cylinders.

Hope this helps, if you need more info, just ask,
Dave

Dec 19, 2010 | 2000 Acura TL

1 Answer

How many o2 sensors does a 98 acura 3.2 tl have


it has 4 2 on each side 1 before cat and 1 after cat

Feb 18, 2010 | 1998 Acura TL

1 Answer

I have a 98 Acura TL 3.2. The check engine light has been on for a while and one of the O2 sensors was on the diagnostic code. I opted out of replaceing it for a while and now I have a flashing check...


When O2 sensor is bad the check engine light coming on is a warning. If you leave it go the computer will go into "limp" mode till it is replaced. You have to give the computer time to recalibrate itself after replacing, up to 150 or so....

Feb 13, 2010 | 1998 Acura TL

2 Answers

04 acura tl serpentine belt diagram


there should be a belt diagram from a label either on underside of hood or on radiator support. That should help if you can do it yourself.

Jan 24, 2009 | 2004 Acura TL

Not finding what you are looking for?
2004 Acura TL Logo

Related Topics:

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...