Question about 1996 Cadillac DeVille

2 Answers

How to replace oil pan seal - 1996 Cadillac DeVille

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How to clean toyota yaris oil sump

Posted on Feb 05, 2015

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 5,370 Answers

For more oil and oil pump details check out the direct links below: ---

How to Replace Oil Pan on car?
http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-oil-pan-on-audi-a4-and.html
--------
How to Replace an Oil Pan Gasket?
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pan-gasket.html
-----------
HOW TO REPLACE AN OIL PUMP
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pump.html
----------
HOW TO CHANGE ENGINE OIL AND FILTER
http://schematicsdiagram.blogspot.com/2011/07/how-to-change-engine-oil-and-filter.html
----------
HOW TO REPLACE AN OIL PRESSURE SWITCH (SENSOR)
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pressure-switch.html
-----------
How to Check Differential Oil Leaks and Replace Oil
http://schematicsdiagram.blogspot.com/2011/07/how-to-check-differential-oil-leaks-and.html
----------
HOW TO PERFORM A BASIC ENGINE TUNE UP-OIL CHANGE
http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up-oil.html

-------


Oil pan Gasket on car?
http://howtobyme.blogspot.com/2011/11/oil-pan-gasket-on-1998-toyota-tercel.html

---------

Oil pressure for car?

http://schematicsdiagram.blogspot.com/2011/12/oil-pressure-for-2001-gmc-jimmy-v6.html

----------
How to replace Oil Pan on car?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pan-on-2008-honda.html

---------
How to replace Oil Pressure Sensor on car?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pressure-sensor-on.html

-----------
How to replace Oil Pump on car?

http://howtobyme.blogspot.com/2011/12/how-to-replace-oil-pump-on-2008-honda.html

----------
Car oil leak?

http://schematicsdiagram.blogspot.com/2011/12/car-oil-leak.html

----------
Car oil leaks from valve cover gasket?

http://schematicsdiagram.blogspot.com/2011/12/car-oil-leaks-from-valve-cover-gasket.html

----------
Oil light blinks on dashboard?

http://schematicsdiagram.blogspot.com/2011/12/oil-light-blinks-on-dashboard.html

-----------
Oil pressure issues on car?


http://repairhelpcenter.blogspot.com/2012/01/oil-pressure-issuers-on-toyota-tundra.html

-----------
Oil leaks from air filter on ford?

http://technoanswers.blogspot.com/2012/01/oil-leaks-from-air-filter-on-ford.html

---------
Wire running from oil pan to alternator?

http://technoanswers.blogspot.in/2012/02/wire-running-from-oil-pan-to-alternator.html

--------------
Why car leaks oil from oil filter?

http://schematicsdiagram.blogspot.in/2012/02/toyota-camry-leaks-oil-from-oil-filter.html

------------
Why engine is consuming lots of oil?

http://schematicsdiagram.blogspot.in/2012/02/2008-scion-xb-24l-engine-is-consuming.html

-----------
Maint REQD message on car dash?

http://schematicsdiagram.blogspot.in/2012/02/maint-reqd-message-on-2008-lexus-rx350.html

------
Remove Sump oil pan?

http://repairhelpcenter.blogspot.in/2012/03/remove-volkswagen-sump-oil-pan.html

--------
Sump not coming OFF?

http://repairhelpcenter.blogspot.in/2012/03/sump-not-coming-off.html

-----------
How to remove the sump on car? http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-sump-on-vw-beetle.html

----------
Car oil sump removal diagram?

http://repairhelpcenter.blogspot.in/2012/03/volkswagen-beetle-oil-sump-removal.html

---------

This will help.

Thanks.


Posted on Mar 03, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace gasket on oil pan for 1987 dodge pickup


  1. Wear eye protection. There is nearly 30 years worth of accumulated must, gunk, etc under that truck. It will fall and find its way into your eyes. Do not skip this part.
  2. Drain oil from engine
  3. Prepare to catch the oil pan when it comes free from the housing. Use a friend is the best method. If you are under it, it will fall on your face and it will hurt.
  4. Remove all traces of the old seal from the housing under the truck and from the oil pan itself. Do not save time on this step, completely remove the old seal.
  5. Install the new seal according to the instructions included with the seal or from the place you purchased the seal. Usually, I install the seal on the pan.
  6. Lift the pan into place and prepare to hold it while you thread the bolts to reattach. If you are under it and it falls or your arms give out it will fall on your face and it will hurt.
  7. Follow the instructions regarding how tight and in what order to replace the bolts.
  8. Replace engine oil. Go ahead and replace the filter and do a complete oil change.
  9. Check engine oil level add more oil if needed.
  10. Wait 10 minutes
  11. Check engine oil level add more oil if needed.
  12. If oil is at appropriate level, start the engine and let it idle until warm.
  13. Turn engine off
  14. Inspect for oil leaks.
  15. Wait 10 minutes
  16. Check engine oil level add more oil if needed.
  17. If the appropriate amount of oil is in the engine and there are no leaks, enjoy driving that truck!

Dec 16, 2015 | Dodge Cars & Trucks

1 Answer

HOW DO I CHANGE MY OIL PAN SEAL


Take out the oil drain plug and drain the oil from the engine(let it drain for about an hour), use a small flat head screwdriver to break the seal between the oil pan and the engine, take it off, make sure you get all of the seal and gunk off of the engine and the pan where the seal goes, replace the seal and add any sealant if required and replace the pan, tighten the bolts from one side to the other and then one side to the other until you tighten them all(like you would the lug nuts on a car's tire). add 4.5 quarts of oil, let it sit for a while and then run the car at idle for around 10 minutes. Done.

Oct 20, 2011 | 1999 Subaru Forester

1 Answer

1992 Ford Crown Victoria Oil Pan is leaking. Is this a major problem to replace? Fred


It is recommended that you lift out the engine before attempting to replace the oil pan. Once the engine is lifted you can remove the bolts, remove the pan, clean all the old gasket material.
Installation: Remove the rear main bearing cap oil seal Remove the timing cover oil seal Clean all the mating surfaces and seal grooves Install new oil pan front cover seals Install a new rear main bearing cap oil seal Install new oil pan side gaskets on the block Make sure the tabs of the front and rear seal fit properly as these are critical spots Attach the oil pan to the engine block and install the retaining bolts

Feb 23, 2011 | 1992 Ford Crown Victoria

2 Answers

Oil Is Leaking Out Under The Harminc Balancer On my 92 Jeep Wrangler,4.0 6cyl. I Replaced The Main Seal & Put A New Balancer On & It Still Leaks From The Bottom Of The Balancer


  1. timing cover is leaking oil betwwen cover and block
  2. Disconnect the negative battery cable.
  3. Remove the drive belt(s), fan and fan shroud. If equipped, remove the accessory drive belt pulley.
  4. Remove the vibration damper retaining bolt and washer. Remove the vibration damper using a suitable puller.
  5. Remove the accessory drive brackets attached to the timing cover.
  6. Remove the A/C compressor, if equipped, and alternator bracket from the cylinder head and move to one side.
  7. Remove the oil pan-to-timing case cover bolts and the cover-to-cylinder block bolts.
  8. Remove the timing case cover front seal and gasket from the engine.
  9. Cut off the oil pan side gasket end tabs and oil pan front seal tabs flush with the front face of the cylinder block. Remove the gasket tabs.
  10. Clean the timing case cover, oil pan and cylinder block gasket surfaces.
  11. Remove the crankshaft seal oil seal from the cover by prying it out with a suitable tool.

To install:

  1. Install a new seal in the timing cover using a suitable seal installation tool.
  2. Apply sealer to both sides of the replacement cover gasket and position the gasket on the cylinder block. Cut the end tabs off the replacement oil pan gasket corresponding to those cut off the original gasket. Attach the end tabs to the oil pan with sealer.
  3. Coat the front cover seal end tab recesses generously with sealer and position the seal on the timing cover.
  4. Apply engine oil to the seal-oil pan contact surface, then position the cover on the cylinder block.
  5. Insert timing case cover alignment tool J22248 or equivalent, in the crankshaft opening. Install the cover-to-cylinder block bolts and tighten them to 62 inch lbs. (7 Nm). Install and tighten the oil pan-to-cover bolts to 11 ft. lbs. (13 Nm).
  6. Remove the cover alignment tool and position a replacement oil seal on the tool with the seal lip facing outward. Apply a light coat of sealer to the seal and a light coat of oil to the crankshaft. Install the seal on the timing cover.
  7. Apply a light film of oil to the vibration damper hub seal contact surface. Install the vibration damper using a suitable installation tool.

Do not hammer the damper into place as damage may result to the damper or engine.

  1. Install and tighten the crankshaft vibration damper bolt to 80 ft. lbs. (108 Nm).
  2. If equipped, install the crankshaft pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
  3. Install the accessory brackets.
  4. Install the fan and fan shroud.
  5. Install the drive belt(s) and adjust to the proper tension.
  6. Connect the negative battery cable.
  7. Start the engine and check for leaks
  8. .

Jan 18, 2011 | 1992 Jeep Wrangler

1 Answer

How to change oil pan seal


start the car and let run for 2 minutes just to warm the oil and make it a little thinner,turn car off. now if you cant get under the car jack ther car up, and let the vehicle rest on jack stands. drain the oil from the oil drain plug which should be on the bottom of the oil pan. once the oil is drained replace the oil drain bolt and tighten it. then remove all of the bolts that keep the oil pan in place. should be around 6 of them. remove oil pan and scrape off the old seal with a clean scraper. place new seal on, and replace the pan. put the bolts back on tightly and refill the engine oil to specified amount. check to be sure there is no leak on the oil pan. turn vehicle on and let the car run for a few minutes. make sure there is still no leak.

Dec 22, 2010 | 1991 Oldsmobile Cutlass Calais

2 Answers

How do you replace a gasket and cover for timing chain and rear seal gasket for oil pan on a 1978 Chevy 350 motor


the oil pan will need to be removed to repalce the rear seal, so replace the front seal and gasket then, replace the timing chain/gears if sloppy, then reinstall the oil pan.

Dec 11, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

How do i fix oil pan leak in a 98 cadillac deville


you have to reseal the oil pan, the oil pan is a 2 piece upper and lower pan. the engine or trans mission has to0 be rtemoved to remove the oil pan per general motors there is new sealer available also the front and rear crankshaft seals should be replaced (need special tools to replace seals)

Aug 18, 2010 | 1998 Cadillac DeVille

1 Answer

Oil Pan Gasket Leak


you oil pan bolts of the bottom of the oil resivour the gaskit fits in between the surfaces where the pan meets it creating a seal witch in your case needs to be replaced this procedure replaces that gaskit to create a new seal

Mar 04, 2010 | 2001 Ford Ranger Regular Cab

1 Answer

Leaking oil really bad and need to know how to replace seal


drain the oil, remove the pan peel off old seal replace with new seal in pan and put the pan back on thighten down and refill to manufacturer seting for oil

Oct 29, 2009 | 1996 Chevrolet Blazer

2 Answers

Oil leak in my 98 mazda protege


Could be a rear main seal.

Apr 02, 2009 | 1998 Mazda Protege

Not finding what you are looking for?
1996 Cadillac DeVille Logo

682 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...