Question about Ford Focus
Just installed a new clutch kit in a ford focus 2007 and it won't start was told it is probably the neutral safety switch need a diagram to see where it is
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: neutral safety switch....I think
The switch is located at the top of the clutch pedal assembly, above your feet. Its a little cramped, but its a simple dc two wire switch, you should be able to check it with a meter for power and to see if the switch does indeed need replacement. If thats the problem, when you see the new switch, you'll know it goes in, very easy. good luck
Posted on Aug 12, 2008
There is a procedure to set the switch so that it will start in neutral and park and not in drive or reverse, there are two slotted mounting holes on the switch for adjustment purposes to get it close put a scribe mark on the old switch in relation to the mounting bolt heads, when installing new switch look at the marks on the old switch to approximately locate the switch in relation to mounting bolt heads. When removing the switch make sure the truck is in park, remove the shift lever nut off the transmission where the Neutral safety switch is, then unplug the wire going to the switch, mark the bolt relation to switch as described and slide switch off the transmission shift shaft, the inside of switch hole is not round it has a flat or square type hole so it can lock into shaft and turn with shaft you may need to rotate the switch back and forth to slide it over the shift shaft when installing the new switch. bolt it on after sliding it over the shaft noting the aproximate location using the scribe marks on old switch, after assembling the shift lever and plugging the wire back in a fine adjustment of switch amy be needed if the starter doesn't activate, get under the truck loosen the hold down bolts for the switch and have an assistant hold the ignition switch to the start position while you rotate the switch when the starter activates lock down the bolts and check after to be sure the truck won't start in drive or reverse adjust accordingly.
Posted on Sep 11, 2009
Testimonial: "Thank you very much for the accurate, easy to understand walk through of the switch install and adjustment. Should have no problems. Thanks again!"
Neutral Safety/Back-up Light Switch
This is a combination switch which controls both Neutral Safety and Back-up lamp circuits.
C6 neutral start switch
Removing the AOD neutral start switch
Removing the Manual Lever Position (MLP) sensor
As of 1994, the neutral safety switch is referred to as a Manual Lever Position Sensor (MLP).
Adjusting the MLP sensor
Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.
I hope help you. Good luck (rated this help).
Posted on Sep 18, 2009
Tips for a great answer:
Feb 15, 2016 | 2009 Ford Fusion
Aug 22, 2014 | 2010 Ford Focus 2.0
Apr 09, 2013 | 2000 Ford Windstar
Apr 03, 2013 | 2003 Ford Focus
May 29, 2017 | 1998 Honda Accord
Oct 16, 2012 | 2003 Ford Ranger Regular Cab
1 - a tank of the hydraulic booster of a steering; 2 - a plug mouth oil-jellied; 3 - a tank of a working liquid of a braking system and clutch; 4 - the assembly block of safety locks and the relay; 5 - an air filter; 6 - a windshield washer reservoir; 7 - the accumulator battery; 8 - the identification tablet; 9 - a measuring instrument of level of oil; 10 - an expansion chamber of system of cooling.Ford Focus engine diagram Ford Focus engine diagram - turbo-diesel of 1,8 l Endura-DI Ford Focus engine diagram - turbo-diesel of 1,8 l Endura-DI
1 - a tank of the hydraulic booster of a steering; 2 - a plug mouth oil-jellied; 3 - a tank of a working liquid of a braking system and clutch; 4 - the assembly block of safety locks and the relay; 5 - an air filter; 6 - a windshield washer reservoir; 7 - the accumulator battery; 8 - the identification tablet; 9 - a measuring instrument of level of oil; 10 - an expansion chamber of system of cooling.
Mar 28, 2011 | 2004 Ford Focus
Aug 03, 2010 | Ford F-100 Cars & Trucks
Aug 12, 2008 | 1988 Ford F 150
350 people viewed this question
Usually answered in minutes!