Question about 2002 Nissan Altima

Open Question

2002 nissan altima will crank but goes dead when put in gear

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jschoon77
  • 55 Answers

SOURCE: DOOR WON'T OPEN FROM INSIDE OF NISSAN ALTIMA 2002 ON DRIVER'S SIDE

There is a cable that attaches to the inside door latch release handle. The plastic that retains this cable is most likely broken. I have seen this before. If the retainer is not holding the cable sheath correctly, the entire cable moves when the handle is pulled and does not release the door latch.

Remove the door panel and inspect this cable. You will see 2 cables (one is for the door lock). If the plastic is broken, you will need a new interior handle assembly.

Hope this is helpful!!



Nissan Scope Technician- 10+ years experience in Nissan dealership

Posted on Nov 11, 2008

Ad
  • 383 Answers

SOURCE: CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA

1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Posted on Apr 06, 2009

  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

  • 54 Answers

SOURCE: Tune up nissan altima 2.5L model 2002

All you really need is a good set of spark plugs, this car has coil packs so no plug wires distributor caps etc.....Just remove the coil packs and install your plugs and your done. Good luck.

Posted on May 31, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima Exterior Door Handle

I seriously doubt that supergluing or even epoxying a handle back will hold at all, or hold for more then few days.
I would only suggest doing the replacement yourself if you familiar with this type of work, or has the aptitude to figure out how to do it, and have the right tools because it is NOT trivial and a number of things can be done wrong, broken or scratched.
The handle itself cannot be replaced. The outside door handle assembly (which includes the handle, the bezel with all associated springs, plastic and metal hardware) has to be replaced. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. And these handle assemblies are not cheap ether. The driver side handle on my 2002 Altima broke first. I paid $60.23+tax, and they had to order it. BEFORE anyone goes to the dealer I suggest to call first, and ask them if they have it in stock. Since door handles are sold painted they will ask you for your car's VIN number so that they match the paint color.
After you pick it up, the replacement will take about an hour (if you know what you doing). The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. You will also need a good flashlight so you see what you are doing.
If you are familiar how to do this type of work and plan to keep the car for a while I strongly suggest buying a factory service manual on a CD (I bought mine on eBay for under $10). It is worth its price 1000s of times over, and makes almost ALL repair work SOOO much easier.751424a.jpg73e3811.jpgd240851.jpg

Posted on Nov 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2002 Nissan Altima 2.5 s transmission won't shift out of 1st gear after being replaced.


first try to manually unlock the shift lock mechanism located on gear shift selector and if that does not work check to see if the linkage is lined up correctly with the according gears, good luck the answer lays within the time of removal and installation, just double check everything.

Oct 23, 2012 | 2002 Nissan Altima

2 Answers

2002 Nissan Altima 3.5 "Choking & Jerking"


I just had the same problem with my '02 altima SE.
Took it to Buckeye Nissan in Hilliard OH. and they had to replace the two crank sensors which.
The sensors themselves were about $44.00 a piece, but w/labor about $300.00 was the total. Hope this helps.....Now if I can just get the heater working!

Oct 08, 2009 | 2002 Nissan Altima

1 Answer

Trouble keeping it running


check fuel pressure from fuel pump, change fuel filter, sounds like it is not getting enough fuel.

Oct 06, 2009 | 2002 Nissan Altima

1 Answer

1993 nissan altima starts sometimes other times it does not crank over battery is good also installed new ignition switch


Could be the starter. Also how are your batter connections? Nice and tight and clean?? If so than check the single wire going into the starter. Not the battery cable, but the small wire that goes into the solenoid. Unplug that wire and put volt meter into the connector on the harness side and check for 12V, while you turn the ignition to "START" position. If 12V is present, suspect the starter.

Mar 01, 2009 | 2002 Nissan Altima

2 Answers

CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA


1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Dec 18, 2008 | 2005 Nissan Altima

1 Answer

2002 altima wont start


check leads for corrosion if thats good i believe you can have autozone check your starter

Aug 13, 2008 | 2002 Nissan Altima

Not finding what you are looking for?
2002 Nissan Altima Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...