Question about 1998 Toyota 4Runner

Open Question

How to remove door panel 1993 toyota 4 runner

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 347 Answers

SOURCE: Remove a driver side door panel on a 2000 Toyota Limited 4 Runner

remove the screws that hold the inside door handle and clips behind the door panel

Posted on Sep 20, 2009

Ad
kidspeedy
  • 321 Answers

SOURCE: removing a starter from a 1993 toyota 4 runner

See Figure 5
Replacing the starter while the engine is cold is recommended. A hot engine can result in personal injury.

  1. Disconnect the negative battery cable.
  2. Remove the nut and disconnect the battery cable from the magnetic switch on the starter motor.
  3. Disconnect the remaining electrical connections at the starter.
  4. Remove the nuts and/or bolts securing the starter to the bell housing, then pull the starter toward the front of the vehicle to remove.

To install:
  1. Insert the starter into the bell housing being sure that the starter drive teeth are engaged with the flywheel teeth, not jammed against the flywheel.
  2. Tighten the attaching hardware to 29 ft. lbs. (39 Nm) and replace all electrical connections.



0900c15280060949.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 5: Exploded view of a common starter mounting found on Toyota trucks

Posted on Nov 25, 2009

  • 389 Answers

SOURCE: inner door panel removeal power window will not 1987 4 runner)

I can lmost guarantee you that it is the switch. If you have a master switch they both may be corroded at the same time.
Before you replace the motor in the window take out the switch rather its in the door panal or arm rest. You can then get a piece of bailing wire or a coat hanger might work and cut a small piece off with wire cutters. About an inch or two long. Bend the wire because after you unplug the wires from the switch you are going to test the window motor. Turn the key to the on position and stick the bent wire into various combinations until you get it to roll up or down. If this works then the motor is good. I can't see how your switch wires look so if the bent coat hanger can't get into them then you need to scrape a bare spot in the different wires so you can cross them with each other. Black electrical tape will cover the bare spots easily. Once you see that it is indeed the switch then you can now take the switch apart. Inside is some contact points that get corroded and won't allow the power to flow through it to give the cpommands you want. Take some steel wool or your wifes emery board and file or clean them nice and shiny. You may see the plastic switch box is sealed. Just pop off the top with a pocket knife. Becareful to see exactly how the parts inside go to gether. I have fixed 4 or 5 this way with a 100% win win situation. But don't worry to much if you can't get them back together. They are a dime a dozen at the wrecking yards for 5 bucks or so. Pick-a-parts where you go in and take your parts off yourself are the cheapest way to go if you need to get one. You can do this with any of the switches but it may be for the low cost that you just want to get the used ones and replace the whole switch by just reconnecting the wires. I am askin flint and choose the hard way to save a penny. LOL So let me know how you fair on this. If you still need to remove the panel and change the motor then let me know and I will explain how. Best of luck, Raz

Posted on Apr 19, 2010

Testimonial: "raz do I need to take take the panel off to do this or can I get the switch out of the door without removing it Thanks Raz "

  • 160 Answers

SOURCE: I have a 1993 Toyota 4 runner and I can't unlock

need to pressure test system possibly minor problem such as heater hose split please rate

Posted on May 05, 2010

  • 160 Answers

SOURCE: starter removal on a 1990 toyota 4 runner. Where

it is not fun w/o lift look behind passenger wheel you will need to raise front end remove wheel ,remove skid pan,and of course battery ends if 4wd I highly reccomend a lift good luck and please rate this

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2011 toyota 4-runner the child lock will not unlock


Then you will need to remove the door panel and replace the door latch assembly. What doo is this, front or rear.

Apr 18, 2014 | Toyota 4Runner Cars & Trucks

1 Answer

1993 toyota 4 runner that feels like it has no breaks.


check the brake booster is working and not leaking. Also check the vacuum pump which may be incorporated into the alternator

Apr 14, 2013 | 1993 Toyota 4Runner

1 Answer

I'm removing a starter on a 1993 Toyota 4 runner and I can't get to the top bolt. I have already loosened the lower bolt. How can I do this


Hi you need ta by a set of starter wrenches the have a bend so you can get to the top bolt if you have starter wrenches it will be no problem. Hans

Jan 18, 2011 | 1993 Toyota 4Runner

1 Answer

Replace rear differential 1993 4 runner


REMOVE BOTH REAR TIRES TAKE BOLTS LOOSE AT BACK OF BACKING PLATES AFTER REMOVING DRUMS AND THE AXLES WILL POP LOOSE .PULL THEM OUT ENOUGH TO CLEAR REAR DIFF INSIDE AND POP OF DRIVESHAFT AND REMOVE ALL BOLTS AROUND THE CASE WHICH HOLDS IN CARRIER ASSEMBLY AND SWAP

Jan 16, 2011 | 1993 Toyota 4Runner

2 Answers

In my 1996 toyota 4 runner my driver side door opens only from the inside. The locks still work and it still opens but not from the outside. How can I fix it?


you have to remove the inside door pannel first remove the arm rest two screws then remove the door latch assembly then remove the crank handle by removing c clip around the wndow knob unless electric, next pop the lower and side screws out of the corners then pop the snaps up from the door remove the lock tab at top pull pannel next gently remove the plastic that covers the door and straighten the rod out on the inside that goes to the outter door handle, if it's not hooked up then you will have to buy a plastic clip from toyota to replace it with.

Aug 14, 2009 | 1996 Toyota 4Runner

1 Answer

Remove a driver side door panel on a 2000 Toyota Limited 4 Runner


remove the screws that hold the inside door handle and clips behind the door panel

Jun 14, 2009 | 2000 Toyota Corolla

1 Answer

Wiring for Toyota 4 Runner Alternator Fuse


it should be in the underhood fusebox on the right.

Apr 14, 2009 | 1993 Toyota 4Runner

Not finding what you are looking for?
1998 Toyota 4Runner Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...