Question about 2007 GMC Sierra 3500HD

Open Question

Need to replace rear wheel studs on 2010 gmc 3500HD

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 125 Answers

SOURCE: we have a 1993 3500HD gmc,the brake lights aren't

Did you check the switch on the brake pedal mechanism under the dash?

Posted on Jan 26, 2011

Zim1308
  • 543 Answers

SOURCE: 2010 gmc terrain replace rear wiper

Wiper blade or arm? If you just need to replace the wiper blade it should just unclip from the arm. There is a small clip inside the blade if you look inside the arm as it loops around. Pry it inward to get it to snap out. Then just reinsert it the same way to reinstall

Posted on Jun 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi,this is devon I have a 2010 30 inch Liebherr fridge. Was bought used, How do i lower the front wheels.


Hey Devo,
The wheels MIGHT have a threaded stud that screws up and down..(it may have a lock nut on the threads),, just loosen the nut and screw the studs inward...If they do not have a threaded stud on the front wheels,,, you might have to raise the rear wheels.. - which in turn.. lowers the front..
Steve

Sep 20, 2017 | Cars & Trucks

1 Answer

How do I change a tire on 2010 Routan?


place the hand brake on firmly--chock other wheels . loosen off the wheel nuts . jack the vehicle up finish removing the wheel nuts . pull the wheel of the studs . fit replacement spare wheel onto studs . do wheel nuts up as tight as possible . lower jack so that the wheel is on the ground . finish tightening the wheel nuts . Replace the jack and wrench in the boot along with the flat tyre . Take the flat tyre to a tyre shop for a puncture repair and have it fixed immediately. Most "people" leave the repair to a later time when they will need a spare that they do not have .The tyre change process is fully described in the owners hand book for your vehicle.

May 29, 2014 | 2010 Volkswagen Routan

1 Answer

Removing rear wheel studs


there should be one spot while turning rear wheel bearing that will allow one stud to be knocked out and new stud replaced BEFORE trying to remove the next stud... one at a time

May 16, 2014 | 2008 Chrysler Aspen

1 Answer

2001 altima replacing rear wheel stud


strip it down to your hub the hub holds the studs .it is a push pull fit .but an old nut on it.then hit the top of it .it when then push in.remove the nut. push in the new stud from the rear of the hub.put a larger nut on top of stud ,then your wheel nut to pull the stud into the hub.then remove the wheel nut .then refit the parts taken off.and fit your wheel.

Dec 30, 2013 | 2005 Chrysler PT Cruiser

3 Answers

How to change broken stud on rear axle 1997 ford explorer


I am assuming you are talking about a wheel lug stud. The lug studs are pressed in from the inner side of the drum or rotor or axle flange depending on how your vehicle is equipped. You have to remove the wheel and drum or rotor to get access to the back side. Drive the broken stud out from the front after you have removed the drum or rotor and set the new one in from the back and tap it into the hole until set as the rest are. If you cant get it set all the way you can finish setting it by pulling it into place when you tighten the lug nuts on reassembly. The part should be under $10.00

Nov 18, 2010 | 1997 Ford Explorer AWD

1 Answer

How do u fix a rear stud on a 1999 Nissan Maxima


You will need to remove the Rear Wheel, Brake Caliper, and Rotor to replace the Stud. Once those are removed, take a Hammer and hit the Wheel Stud from the front to drive the Stud out through the back of the Wheel Hub. Once the Stud is out, take the new Stud and insert it in the Hub from the back. You will need to get a Open Ended Nut with the proper thread size as the Stud and thread it on the Stud, and tighten the Nut till the Stud comes all the way through the hole and the end of the Stud is flush with the back of the Hub. Remove the Nut and you can now put everything back together.

Jul 15, 2010 | 1999 Nissan Maxima

1 Answer

How do I replace the studs on the rear wheel


remove wheel and brake assembly, drive broken stud through back off the hub. Put new stud through hole and use a spacer and an old lug nut to pull stud till its seated in hub.

Feb 27, 2010 | 1993 GMC Suburban

1 Answer

Broken wheel stud


Unless you hit a curb or something you have bumper to bumper warranty for 3yrs.36 k miles.If not then you can remove the wheel and brake caliper and rotor.Then pound the stud out with a hammer and reinstall the new one.Use a socket or some type of spacer and put on new stud once you have put the stud through the axle.Install the new nut on and start tightening til the stud is seated on the axle.Reinstall the wheel and torque to specs.Depending on type of wheel could be 80-100 ft.lbs.Hope this helps.Good luck.

Dec 23, 2009 | 2002 Pontiac Grand Am

1 Answer

Broken rear wheel stud on a 2005 ford focus zx4 se


  1. Step 1 Buy a new stud. Make sure you purchase the right size. If you're not sure what size to get, wait until you remove the stud and take it with you to the store.
  2. Step 2 Check the area of the spare tire in the trunk for the jack and the jack tools since you'll need to raise the car to replace the wheel stud on your Focus. Be sure to block the tire diagonal to the jack.
  3. Step 3 Use the jack to raise the Focus. Remove the wheel Take off the caliper and either hang it by a mechanics wire or lay it up so it doesn't dangle by the brake line. Remove the rotor. If you're working on back wheels, you have to remove the emergency brake clip first. You could have drum brakes in the rear. If they're drum brakes, remove the drum.
  4. Step 4 Hunt for an opening behind the hub that allows you to remove the stud. Line the stud up with the hole. You may have to take off the hub and put it in a vise if you can't drive it out the back.
  5. Step 5 Hit the stud with a mallet and drive it out the back of the hub. Push another stud into the opening. This is tough work, but you only need to push it far enough to thread on a wheel bolt.
  6. Step 6 Put on a wheel bolt and begin to tighten it. As you do, the stud starts to pull through. Add more bolts as necessary until you seat the stud. Check in the back of the hub. When the head is flush with the stud, you seated it.
  7. Step 7 Remove the extra bolts and reassemble the parts that you took off to replace the wheel stud on the Ford Focus. Put the wheel back on the vehicle and tighten down the wheel nuts.

Sep 25, 2009 | 2005 Ford Focus

1 Answer

Changing Rear Rotor Studs


These studs are 'pressed' in at the factory, and really should be replaced by a professional.
At the very least you would need a shop press and/or apowerful air compressor and impact gun.
First, are they in the rotor or the hub. (I don't know if this is a4x2, 4x4, etc.) If they are in the hub itself, this MUST be done by a professional. If they are in the rotor, I would seriously consider replacing the rotor, which in some cases can actually be cheaper.
If you don't want to replace the rotor, please take it to a qualified mechanic, parts store (some do this type of work regularly), or machine shop.
Although I could describe how to do it, an improperly seated wheel stud could have tragic consequenses. Good Luck!

Aug 06, 2008 | 2002 GMC Yukon XL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...