Question about Dodge Grand Caravan

Open Question

Step by step 2001 dodge G C es 3.8 front blower motor R&R

R&r front blower motor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: air conditioner blower motor resister on dodge grand caravan

in my 2004 grand caravan it's behind the glove box and left of the blower motor. disconnect the wires first then remove the 2 screws to pull out the resistor unit. First make sure you have removed the negative of your batterie. I had the same pm that prevented the blower motor to operate in any speed. I hope this will help

Posted on Dec 25, 2008

Ad
  • 1596 Answers

SOURCE: 2005 Town Country front blower motor inop fuse/relay ok

Break Down And Replace The Blower Motor


REMOVAL

WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, DISABLE THE AIRBAG SYSTEM BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. DISCONNECT AND ISOLATE THE BATTERY NEGATIVE (GROUND) CABLE, THEN WAIT TWO MINUTES FOR THE AIRBAG SYSTEM CAPACITOR TO DISCHARGE BEFORE PERFORMING FURTHER DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE WAY TO DISABLE THE AIR-BAG SYSTEM. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN AN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY OR DEATH OR DEATH.

NOTE: The blower motor is located on the passenger side of the vehicle under the instrument panel. The blower motor can be removed from the vehicle without having to remove the HVAC housing.

  1. Disconnect and isolate the negative battery cable.
  2. Remove the passenger side cowl trim panel.
  3. Position the carpet to access the front upper screw that secures the air inlet housing.
  4. Remove the recirculation door actuator.
  5. Disconnect the blower motor wire lead connector from the blower motor resistor or power module, depending on application.
    1. Remove the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing.
    2. Remove the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and remove the lower HVAC housing.
    3. Push the rubber grommet through the opening in the lower air inlet housing.
    4. Route the blower motor wire lead through the opening in the lower air inlet housing and remove the lower air inlet housing from the vehicle.
    5. Position the recirculation-air door as necessary to access and remove the three screws that secure the blower motor to the lower half of the HVAC housing.
    6. Gently flex the recirculation air door downward to gain access to remove the blower motor from the HVAC housing. NOTE: To aid in installation, note the position of the blower motor mounting tabs prior to removal
      1. Remove the blower motor from the HVAC housing by rotating and tilting the blower motor as necessary.
      INSTALLATION

      1. Gently flex the recirculation-air door downward to gain access to install the blower motor into the HVAC housing.
      2. Position the blower motor to the HVAC housing and tilt and rotate the blower motor as necessary to install it into the HVAC housing.
      3. Align the blower motor mounting tabs to the locations noted during removal and install the three screws that secure the blower motor to the HVAC housing. Tighten the screws to 2 N·m (17 in. lbs.).
      4. Route the blower motor wire lead through the opening in the lower air inlet housing and seat the rubber grommet.
      5. Position the recirculation door pivot shaft into the lower air inlet housing and install the inlet housing.
      6. Install the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and the lower HVAC housing. Tighten the screws to 2 N·m (17 in. lbs.).
      7. Install the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing. Tighten the screw to 2 N·m (17 in. lbs.).
      8. Connect the blower motor wire lead connector to the blower motor resistor or power module, depending on application.
      9. Install the recirculation door actuator.
      10. Reposition the carpet.
      11. Install the passenger side cowl trim panel.
      12. Reconnect the negative battery cable.
      13. Perform the heater-A/C control calibration procedure.

Posted on Feb 07, 2009

mkv0525
  • 358 Answers

SOURCE: heat/ac blower motor

ce the resister for blower motor.

Posted on Jun 05, 2009

shadoro
  • 2 Answers

SOURCE: Blower Motor Resistor - 2001 Dodge Grand Caravan

I had the same thing happpen with mine. The unit is located behind the glove box and is just left of the fan held in place with two screws. I bought a new resistor from radio shack and installed it in the unit.

Posted on Jun 06, 2009

wilsodfarm
  • 986 Answers

SOURCE: blower motor stuck on high! 2001 town &country

your blower resister is bad and you need to replace it.......heres how,The glove box can be lowered all the way out of the way just by pulling in the sides so the rubber stoppers come out toward you. The sides bend easily to allow that.

The glove box being out reveals the resistor in the heating duct right in front of you. Just remove the two sets of wires and two bolts (10mm socket, I think) and the resistor pack slides right out. Then bolt in the new one an plug the wires back in (they only fit in one way). Fold the glove box back up and press the stops in to get them back in place and you are done.

The resistor pack only cost $12 and change at my dealer. It is part number 1-04885583AB which was a replacement for the same number with AA at the end, so I’m guessing they had a lot of trouble with the AAs and so made a better AB.

Last Winter my heater blower fan worked only on High. I changed the front heater/AC blower resistor pack and was surprised at how easy it is, but I had to figure it out for myself since my Dealer's parts guy was no help as to where the part lived and my Haynes manual was just plain wrong. This was on a 2001 T+C. I'd be very surprised if the 2001 Caravan was any different. Don't know what other year vans would be the same. I do know some earlier generations had this resistor under the hood and Haynes had is with the blower sort of behind the instrument cluster.

Posted on Jan 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the heater resistor on a 2005 dodge dakota? Behind glove box?


should be just above the blower motor. You will need to remove the glove box door to gain access.

Dec 12, 2015 | 2005 Dodge Dakota Club

1 Answer

My front heater won't blow. we have checked the resistor, changed the blower motor, thermostat and relay. Any ideas as to what it could be/ I do daycare and need the front heat.


In the diagram, check fuse 10--40 amp, not only check the fuse, check the fuse circuit for voltage with hvac on. Use a test light to check for voltage. See the wires going to front blower motor, that is voltage and ground, check them both. Also, the front blower module could be causing a problem? The diagram is for automatic hvac.
25991513-ic5gnyte5ew2v2ubeve5ymta-3-0.jpg

Dec 03, 2015 | 2001 Dodge Grand Caravan

2 Answers

2001 Dodge Durango front and. Rear heat front floor no heat


http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?fromSearchPage=true&pageId=0996b43f80375f32&partName=Timing+Belt+Cover,+Belt+&+Sprockets&partId=0996b43f80375f32 SAVE 20 GET 10 GIFT CARD ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE

Nov 06, 2015 | 2001 Dodge Durango

1 Answer

Where is located the fan speed control stratus 01


Could be your blower motor resister,it's located by blower motor,easy to remove.Click here to see blower motor resistor.

Dec 26, 2012 | 2001 Dodge Stratus

1 Answer

The front a/c blower does not work, all fuses are good. please help


J, I am sending you some info to read but it appears that the most likely cause is the blower motor relay. Give the following notes a read and if you need some more help give me a buzz... Best of Luck..

1996 Chrysler Town & Country 3.3L, Vin R 1996 Dodge Grand Caravan ES 3.8L, Vin L 1996 Chrysler Town & Country LX 3.3L, Vin R 1996 Dodge Grand Caravan LE 3.8L, Vin L 1996 Dodge Caravan LE 3.8L, Vin L 1996 Dodge Grand Caravan SE 3.3L, GAS, Vin R, Eng Cfg V6 1996 Dodge Caravan Sport 3.3L 1996 Plymouth Grand Voyager SE 3.3L, GAS, Vin R, Eng Cfg V6 1996 Dodge Grand Caravan ES 3.3L, Vin R 1996 Plymouth Voyager Rallye 3.3L Customer Concern: Front blower does not work; no power to it. Fuse is OK. Tests/Procedures: 1. At the blower motor, there is a Dark Blue wire. This wire should have battery voltage whenever the key is in the "on" position. Power for the blower motor comes from the blower relay.

2. Access the front blower relay, it is located on the driver's side under the dash, near the junction block. There will be four wires going to it. The Dark Green wire should have battery voltage all the time. The Dark Blue wire is going to the motor. The Black/Orange wire should have battery voltage with the key in the "on" position. The Black wire should be grounded at all times. On this circuit, the relay is energized whenever the key is in the "on" position. Potential Causes: Front Blower Relay
Front Blower Relay Wiring
Heater Ventilation Air Conditioner (HVAC) Control Head
Tech Tips: The front blower relay is located under the dash, on the driver's side. It may be necessary to remove the junction block (fuse and relay box) in order to see it. Diagnostic Codes: None

Aug 28, 2011 | 1996 Chrysler Town & Country

1 Answer

Where is the fuse relay for the power windows 2001 dodge neon es


The power windows receive power from circuit 30 amp breaker #1 in the fuse block. Power flows from the breaker to the master switch then to the doors and window motors.

Apr 20, 2011 | 2001 Dodge Neon

2 Answers

The front heater/air conditioner blower stopped


First check the voltage at the front blower moter. If it has voltage then it may just need a new motor.

May 17, 2010 | 2001 Dodge Grand Caravan

1 Answer

Fan switch works on only one speed


  1. Disconnect and isolate the battery negative cable.
  2. From the passenger foot well area, remove the two hex screws used to secure the blower motor resistor.
  3. Unplug the front blower motor resistor from the wire harness connector.
  4. Pull the front blower motor resistor and its wire harness out of the plenum panel and through the cowl plenum access hole far enough to access the wire harness connector.
  5. Remove the front blower motor resistor from the cowl plenum.
INSTALLATION
  1. Plug the blower motor resistor into the wire harness connector.
  2. Install the blower motor resistor to the cowl plenum panel by feeding the resistor and wire harness back through the cowl plenum access hole.
  3. Install and tighten the two screws that secure the resistor to the HVAC unit Tighten the screws to 2.2 Nm (20 in. lbs.) .
  4. Connect the battery negative cable

May 27, 2009 | 2001 Dodge Dakota

2 Answers

Heater blower


your blower resistor is bad

Apr 21, 2009 | 2001 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...