Question about 1983 Nissan 280ZX

Open Question

Hydrolic clutch pedal sticking

Clutch pedal will not return

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

shanat
  • 359 Answers

SOURCE: clutch pedal sticks

could be the slave cylinder or throw out bearing even clutch itself if replacing it anyway you should also get a kit for your slave cylinder just to be sure i dont think it would be a pedal problem and also if by chance its cable it could be a sticky or frayed cable if you need more info just ask please dont rate me until i have helped you fully

Posted on Jun 13, 2008

  • 60 Answers

SOURCE: 96 pathfinder clutch pedal has lost pressure,

usually when this happen you lost fluid pressure look for a fluid leak at the clutch master cylinder under the hood ,it should be by the brake master ,it has a small plastic tank on top with a black rubber cap or underneath on the transmission there is the clutch slave cylinder it will have a small 2 inch rod that pushes the clutch fork ,look for the rubber boot on it ,see if there is fluid coming out of it ,also follow the clutch fluid lines maybe somthing has damaged one and its leaking !

Posted on Aug 08, 2009

  • 28 Answers

SOURCE: clutch pedal will not return

if you are not loosing fluid in clutch master cylinder than the master cylinder is goin bad. if you are loosing fluid than the slave cylinder is leaking and will have to be rebuilt or replaced. this is a simple answer ,but you didnt give much detail of your vehicle so . this is the best answer i can give

Posted on Feb 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why dose the clutch pedal stick down on my peugeot ?


The linkage between the pedal and the clutch throwout bearing needs attention - the return spring appears to not have been reinstalled correctly, or has broken.

Jul 29, 2014 | Peugeot 405 Cars & Trucks

2 Answers

Clutch problem


I would think you have a hydraulic clutch, so there should be a return spring on the pedal or the master cylinder.

Jan 29, 2014 | Subaru Cars & Trucks

1 Answer

How to bleed a clutch


Get a friend to help. Press clutch down to floor and hold, have your friend loosen the line at the slave cylinder, or clutch actuator under the car enough that fluid squirts out. Have him tighten the line back up. Release the clutch and press back to the floor again. Have your friend repeat the process as before. (loosen to let fluid squirt out, then tighten back up) Release the pedal. Repeat this process untill there are no air pockets left in the line. NOTE: if your clutch pedal fails to return to the top, simply pop it back up with your hand/foot, wait a few seconds, then depress to floor again for another bleeding.

Nov 19, 2013 | 2001 Ford Focus

1 Answer

Clutch pedal not returning occasionally


Check the linkage if it has one. If it has a hydrolic clutch, make sure it is full and there are no leaks. The clutch cylinder, if it has one, may be going bad. If it has a mechanical clutch, the linkage may need lubed or it could be binding on something.

Aug 16, 2012 | 1994 Toyota Land Cruiser

1 Answer

How to bleed slave cylinder on a 1993 mazda mx3


keep you fluid level above 3/4 full- assuming you have a hydrolic clutch- unhook negitve battery cable remove rubber cap from bleeder screw on the release cylinder.place place a bleeder tube over the end of the bleeder screw.sumerge other end in a jar thats half full of hydrolic brake fluid.slowly pump the clutch pedal fully and let return slowly several times requires two people while pressing clutch to the floor lossen bleeder untill fluid comes out then close keep repeating this while keeping an eye on your bleeder tube jar as soon as you see no more bubbles close the bleeder screw and again make sure to keep an eye on resivor to remain 3/4 full or will get air in the line and have to start over. this part should be located on the tranny this is for hydrolic bleeding system refure to your owners manual for your type and location of your clutchrelease slave cylander.

May 04, 2011 | 1993 Mazda MX-3

1 Answer

Clutch pedal sticking not returning to original position


If its a hydrolic clutch, you may need fluid.

Feb 18, 2011 | 1995 Honda Civic

2 Answers

Clutch will not engage when depressed


there could be one of a few issues here.
1 the thrust bearing may have gone which sites on the clutch plate prongs and the actuator arm.
if you have somebody who can depress the pedal while you go under and have a look at whats going on.
2 as this is a hydrolic assisted clutch there may be air got into the system which may show resistance but there is not enough pressure to push the clutch plates so the stay engaged.
when was the clutch fluid last replaced? as same as break fluid is will absorb moisture over time and reduce is effectiveness.
3. the clutch plates may have overheated last time round and welded together so they will not come apart and will have to be replaced.
do you drive with your foot covering the clutch pedal? this style of driving can cause the clutch to overheat as their is never full pressure during driving always leave your feet away from the clutch pedal once you have changed gear.

Nov 12, 2009 | 1995 Ford F150 Styleside Regular Cab

1 Answer

Clutch sticks when pushed to floor


a clutch pedal that doesn't return back to you is sometimes a symptom of a failing clutch slave or general fluid leak. This is of course referring to a hydraulic clutch. If your fluid gets too low or there is an air leak your pedal will stick to the floor and not return.

Oct 26, 2009 | 1994 BMW 3 Series

2 Answers

92 Eagle Talon Clutch pedal won't return fully


fill your clutch fluid, it tells you what kind of brake fluid to use on the cap, and then bleed your clutch system as you would your brakes, the bleeder is located on the slave cylinder i believe

Oct 04, 2008 | 1992 Eagle Talon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...