Question about 1997 Mercury Villager

Open Question

I need engine belt placement diagrams for 1997 mercury villager

Engine belt diagrams

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Timing Belt

I have used the Haynes Repair Manual for the Mercury Villager to change the timing belt on my 1993 Villager, twice. I just finished last night with the latest change. I found the Haynes manual to be very useful. This is just an overview:
1. Jack up the the van and support it on jack stands. Remove the front passenger side wheel and 2 plastic splash sheilds.
2. Remove the two radiator hoses on the passenger side of the engine.
3. Remove the pulley from the water pump (4x 10mm bolts)
4. Remove the tensioner pulley, including the bracket, for the A/C compressor. (3x 12 mm bolts)
This one can be difficult because it requires a torx head to loosen the pulley and it's a very tight fit to get a torx in there. I ended up taking the torx head out of the socket then turning it with a 10mm wrench.
5. Remove all 3 drive belts.
6. Remove the crankshaft pulley. (1-1/16" bolt) You will need a good strap wrench to keep the pulley from turning or an impact to remove this bolt. You may be able to remove the pulley just by bumping it with a mallet, but you may need a gear puller.
7. Remove the timing belt cover, it has an upper and lower half and is held in place by several 8mm screws.
8. You will find that the timing belt pulleys on the both cam shafts and the crank shaft have a white paint mark on one tooth. Make sure the marks on the two cam shaft pulleys are in line with a "bump" mark on the back plate of the belt cover. The bump mark for the front cam is located at about the 2 o'clock position and the one for the rear cam is at about the 10 o'clock position. You will need a mirror and flashlight to see this one.
The crankshaft pulley mark lines up with a notch in the oil pan (I think it's the oil pan where the notch is, but you will see it at near the 6 o'clock postion.
9. My new timing belt was a DAYCO and it came with a good instruction sheet. The new belt has an arrow that should point AWAY from the engine. There are also 3 lines on the new belt that will line up with the lines on the timing belt pulleys.
10. The belt tension should be adjusted so that you get about 0.5" - 0.6" of deflection at the center between the two cam shafts.
Note: I recommend replacing both the tensioning pulley and water pump while you are in there.
A water pump is about $32 and the tensioning pulley is about $35 but it's money well spent.
I did NOT replace the tensioner pulley the last time I changed the timing belt, and that is what failed this time. I could have saved myself a lot of work if I had replaced the pulley the first time.

Hope this helps. I'd still buy the HAYNES manual.

Posted on Dec 16, 2008

Ad
  • 4369 Answers

SOURCE: engine diagram for 2001 mercury cougar

4 cyl or v 6?

2.5L V-6 with air conditioning built 01/99 onwards

84cab79.gif

Posted on Jan 22, 2010

alicantecoli
  • 22219 Answers

SOURCE: radio wiring diagram 1998 mercury villager

buy a conversion cable

Posted on Nov 29, 2008

  • 1757 Answers

SOURCE: need a serpentine belt diagram for a 2001 mercury sable

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/2001/make/mercury/model/sable/2001_mercury_sable_drive_belt_routing_diagram.htm

Posted on Mar 06, 2010

  • 1757 Answers

SOURCE: I need a diagram of the firing order for a 1997 montaineer

For the 1997 Mercury Mountaineer V8 5.0L Engine:

Firing Order:
1-3-7-2-6-5-4-8

Cylinders:
.......(back)......
|..4..|........|..8..|
|..3..|........|..7..|
|..2..|........|..6..|
|..1..|........|..5..|
.......(front)

Ignition Coil Connections:
(back)........(back)
|.4..7.|........|.3..5.|
|.8..2.|........|.6..1.|
(front)........(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Posted on May 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    1 Answer

    Picture of a belt diagram


    heres a diagram for 2004 grand prix with the 3.8 engine, this diagram shows also the diagram if you have the supercharger on that engine , then you would have two belts, if you do not have charger then just ignore the charger belt diagram. hope this helps.240b3b0.gif

    Aug 28, 2010 | 2004 Pontiac Grand Prix

    1 Answer

    I need a diagram for a installing a serpintine belt in a 2005 toyota tacoma


    Depends on engine. Copied below diagrams from AutoZone.com:

    Drive Belt Routings




    0996b43f80209580.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Accessory drive belt routing-2.4L engine



    0996b43f80209581.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Accessory drive belt routing-2.7L (3RZ-FE/M) engine



    0996b43f8020209e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Accessory drive belt routing-2.7L (2TR-FE) engine



    0996b43f80209582.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Accessory drive belt routing-3.4L engine

    Aug 26, 2010 | 2005 Toyota Tacoma

    3 Answers

    Belt routing diagram for1999 Toyota Corolla


    Thats a 98 belt routing same engine. 99 wouldnt load1021f4c.jpg

    Jul 02, 2010 | 1999 Toyota Corolla

    2 Answers

    Need diagram of drive belt assembly forcaddy


    You didn't list your motor size so please pick the applicable diagram:

    ba0b112.gif
    Accessory serpentine belt routing—4.8L, 5.3L & 6.0L engines

    9dcebd3.gif
    Accessory serpentine belt routing—5.7L engines with A/C

    bb89ba7.gif
    Accessory serpentine belt routing—5.7L engines without A/C

    27f4999.gif
    Accessory serpentine belt routing—6.5L Diesel engines

    4d67005.gif
    Accessory serpentine belt routing—7.4L engines

    491a0a4.gif
    Accessory serpentine belt routing—8.1L engines

    Oct 26, 2009 | 2002 Cadillac Escalade Ext

    1 Answer

    Idler for the super charge belt broke off of the motor. I purchased a new idler, but there is no diagram in the manual. Is the diagram on the crossmember for the serpentine belt for the engine and...


    that engine uses 2 belts I believe. if the diagram isnt clear, draw your own. Gates belts has diagrams for belt routings, on their website, look up yiu car, find the belt, then click on the camera icon to see the routing.

    Oct 23, 2009 | 1998 Buick Regal

    4 Answers

    Timing Belt Replacement+Diagram


    How to replace engine belt 1999 ford escort

    Oct 29, 2008 | 1999 Ford Escort

    5 Answers

    Serpentine belt replacement


    2.0L Engines
    See Figures 11, 12 and 13
    The accessory drive belt for 2.0L engines has no provision for manual belt adjustment, since these engines use an automatic belt tensioner. Drive belt slack is taken up by the automatic tensioner.
    Movement of the automatic tensioner assembly during engine operation is not a sign of a malfunctioning tensioner. This movement is the tensioner self-adjusting and is required to maintain constant belt tension.
    The belt tensioner has a belt length indicator. If the indicator marks are not between the MIN and MAX marks, the belt must be replaced.
    0900c1528008d836.jpgFig. 11: Drive belt routing-2.0L SOHC engine with A/C 0900c1528008d837.jpgFig. 12: Drive belt routing-2.0L SOHC engine without A/C 0900c1528008d838.jpgFig. 13: Drive belt routing-2.0L DOHC engine

    Jul 24, 2008 | 1999 Ford Escort

    3 Answers

    Belt routing


    My Ford Taurus does not have the belt routing in the engine compartment on the front clip, or under the hood. Do you have a diagram of the belt routing?

    Jun 07, 2008 | 2003 Ford Taurus

    Not finding what you are looking for?
    1997 Mercury Villager Logo

    Related Topics:

    196 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mercury Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    fordexpert

    Level 3 Expert

    5530 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Are you a Mercury Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...