Question about 1997 BMW 328

1 Answer



Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

Hello yes remove the cover and the wires that cross in front of it ,it will still be just right the size for the blower to come out. then play a litle with the blowermotor and the fins and it will come out. when replacing it i will recomend to replace the blower motor resistor also .

Posted on Nov 23, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Remove heater core 2003 dodge stratus

This is a BIG job, requiring removal of the dashboard, discharging the a/c system, and removing the heater/airconditioning unit from the car (a big box with the evaporator, heater core, blower fan, and various doors that direct airflow). If you want to DIY, there are several videos on YouTube for similar models - you can view those to get an idea of what is involved.

Oct 29, 2016 | 2003 Dodge Stratus

1 Answer

Remove blower fan1988escort

Ford Escort Heater AC Blower Motor Removal - YouTube

? 4:49
Aug 28, 2013 - Uploaded by richpin06a
Ford Escort Heater AC Blower Motor Removal. ... How To Fix Install AC Heater Fan Blower Motor 1991-03 ...

Nov 01, 2015 | 1988 Ford Escort EXP

1 Answer

Heater and a/c blower motor will not work how do you replace it?

  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 13, 2010 | 1999 Oldsmobile Aurora

    1 Answer

    Hi, i need to remove and replace the blower motor for the a.c./ heater, and dont know where it is located. can you please help?

    Blower Motor Removal & Installation To Remove:
    1. Remove the insulator from under the right side of the dash.
    2. Disconnect the electrical connector from the blower motor.
    3. Remove the blower motor retaining screws.
    4. Remove the blower motor.
    To Install:
    1. Install the blower motor.
    2. Install the blower motor mounting screws.
    3. Connect the electrical connector to the blower motor.
    4. Install the under dash insulator.
    prev.gif next.gif

    Dec 10, 2010 | 1999 Pontiac Grand Prix

    2 Answers

    Blower motor removal in a 1999 mercury cougar

    SECTION 412-02: Heating and Ventilation 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/8/2001 Blower Motor Removal
    1. Remove the footwell upper trim panel (passenger side).
      • Remove the pushpins.
    1. Remove the blower motor.
      1. Disconnect the electrical connector.
      1. Lift the securing tab, turn the motor approximately 30 degrees counter-clockwise and remove the motor.
    1. NOTE: Engage the securing tab for the blower motor.

    Nov 12, 2010 | 1999 Mercury Cougar

    4 Answers

    1999 Chev Venture Heater core do I need to remove Dash to replace?

    The blower motor location can change from year-to-year. It can also change with the trim level of the vehicle. A vehicle that has front and rear climate controls may be configured differently than a vehicle that has front controls only. The following are two different repair procedures. One is for blower motors located and accessed in the engine compartment, the other is for blower motors mounted inside the vehicle.


    Engine Compartment Mounted
    1. Disconnect the negative battery cable.
    2. Remove the engine air cleaner assembly.
    3. If necessary for clearance, remove the left hand wiper arm linkage.
    4. Detach the wire harness connector from the blower motor.
    5. Disconnect the motor cooling hose.
    6. Remove the blower motor assembly retaining screws
    7. Carefully pull the blower motor assembly out from the firewall.

    Oct 08, 2009 | 1999 Chevrolet Venture

    1 Answer

    Blower motor fuse is located 99 mercury cougar

    SECTION 412-04: Control Components 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Blower Motor Resistor Removal
    1. Remove the upper footwell trim panel (passenger side).
      • Remove the pushpins.
    1. Disconnect the blower motor resistor electrical connector.
    1. Remove the blower motor resistor.

    May 06, 2009 | 1999 Mercury Cougar

    1 Answer

    Bad heater core

    to change this heater core is a big job, I did mine on my 99 F150, which is incredibly similar, it requires the removal of the complete dash to remove the environmental control station (heater core/air conditioning evaporator). If you are not comfortable with removing basically the whole dash, I recommend that you take it to a good shop in your area. If you are comfortable with it, then you should get a Haynes or Chilton Manual and follow the steps listed in those manuals.

    To bypass you would have to disconnect the two heater hoses on the right side of the engine compartment at the engine connectors and install a hose between the two.

    Apr 14, 2009 | 1999 Ford Expedition

    1 Answer

    I have a 2000 ford E350 van with front and rear air. the front blower motor runs at low speed, The front blower still runs on low even when the knob is set on medium or high. I do not know where the...

    it's either the blower motor switch or blower motor resister. Resistor ?Heater Blower Motor Switch Removal Remove the battery (10655) ; refer to Section 414-01 . Remove the battery tray. Remove the screws. Remove the battery tray. Disconnect the heater blower motor switch resistor connector. Remove the heater blower motor switch resistor (18591). Remove the two screws. Remove the heater blower motor switch resistor. ----------------------------------- Switches Removal Disconnect the battery ground cable. Remove the center trim panel; refer to Section 501-12 . Remove the control assembly. Remove the screws. Remove the control assembly. Remove the A/C-heater function selector switch knob. Disconnect the vacuum harness connector. Disconnect the A/C-heater function selector switch connector. Remove the A/C-heater function selector switch. Remove the screw. Remove the A/C-heater function selector switch. Remove the temperature control switch knob. Disconnect the temperature control switch connector. Remove the temperature control switch. Remove the screw. Remove the temperature control switch. Remove the heater blower motor switch knob. Disconnect the heater blower motor switch connector. Remove the heater blower motor switch (18578). Remove the screw. Remove the heater blower motor switch. ----------------------------

    Mar 31, 2009 | 2007 Ford E-350 Super Duty Length XLT

    1 Answer

    Front fender removal

    Hiya... here's the details of fender removal/installation:
    the left-side (same for right-side) fender has 6 bolts attached to the "sidebody" frame.
    The bolt location:
    3 are on the top fender-easy to find when hood is open,
    1 is hidden at the rear of top inner fender-just open the left-front door wide to find it (early equinoxes had foam-like noise absorber material in it, just remove it from underneath fender after the wheelwell liner is removed),
    1 bolt is hidden at bottom of front fender area at headlight/bumper area-you need to remove plastic wheelwell liner to gain access,
    1 bolt is hidden at bottom of rear fender area where the black plastic rocker panel meets below the fender...
    THIS area is probably the most difficult task to do since it requires you to remove a small bolt found on the front of rocker panel behind the front-left wheel then use a flat screwdriver or clip removal tool to pry open the black plastic **clip's 'dime-sized' head prior to pull out the clip's body (it has 8 clips underneath the chassis) then use your hands to grasp the rocker panel underneath, pull it down-toward you...this should do it....USE CARE during rocker panel and clip removal/installation so you don't break the clips!
    It also has yellow plastic clips inside the rocker panel (used as a guide during installation into rocker sill holes-use caution not to break it)
    **note: early equinoxes had rocker panel clips that you can actually pull it out from the hole, while later equinoxes has 'built-in' clips inside rocker panels that you don't see the clip heads below it due to engineering part design change**
    Be sure to exercise care when handing this task!


    Nov 20, 2008 | 2005 Chevrolet Equinox

    Not finding what you are looking for?
    1997 BMW 328 Logo

    Related Topics:

    235 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top BMW Experts

    Anthony Jones
    Anthony Jones

    Level 2 Expert

    128 Answers


    Level 2 Expert

    254 Answers


    Level 2 Expert

    281 Answers

    Are you a BMW Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides