Question about 2005 Jeep Grand Cherokee

1 Answer

How can I stop the alarm horn noise to stop going off when I open my already unlocked doors

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 77,201 Answers

There is a small micro switch inside the door that is defective replace it. It is activatred by door latch.

Posted on Feb 17, 2012

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 691 Answers

SOURCE: Can not disarm alarm on 2002 jeep grand cherokee

First, try to re-programme the RKE (Remote Keyless Entry) transmitters before searching for anything else. Assure that the batteries in the transmitters are in working condition and replace them if you are not sure. To pro-gramme the transmitters, perform the following:

Open the driver's door and let it be open throughout the programming process. Then, shift the mechanical door lock lever to the LOCK mode, turn the ignition key to the rUN mode. Within a period of twenty seconds, point a transmitter at the receiver dome and push the lock button for a period of five seconds at least. After the receiver has accepted the programming code the driver's door will unlock on its own. The first transmitter has been programmed, in the same extra transmitters up to four may be programmed in the same way, within twenty seconds.
If the alarm does not work properly, you may have a faulty alarm module and may have to be replace and its common problems with and older model. the systems work like a security systems, if you arms your system with the remote you have to disarm it also with the remote in order for the engine to start and run. The logic in the PCM prevents the VTSS engine no-run feature from arming until the engine start; Its one of the security systems jeep has and if you ask for my opinion its junk. hope that help some..

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hazard lights flashing and alarm sounding. How do I stop these?


Every car brand and model has its procedure to stop the flashing light and alarm sounding.
But still the common procedure is Make sure boot and bonnet are closed properly.

It can also be a switch, but check your alarm by locking yourself inside the car, and then press the close button on the key 2 times repeatedly until the lock control on the door doesn't make anything. Then open the door by pushing the lever or open the hood . If the horn sounds and the lights blink your alarm is ok , if only the lights blink you should take it to dealer. You can stop the hazard lights and horn sound by pressing the unlock button on the key.

May 12, 2016 | Cars & Trucks

Tip

How to set & cancel theft deterrent system or how to set & cancel security...


Theft deterrent system (on some models)

Theft deterrent system is designed to deter vehicle theft. The system flashes the turn signal lights and turns on the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn when it detects abnormalities such as follows:

• Any door or hood is forcibly opened.
• The batter terminal is disconnected and then reconnected
• The system control is disconnected and then reconnected.
• Abnormal impact is detected when the impact sensor function is on.

The system flashes the turn signal lights and turns the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn if someone attempts to damage or break into your car.

Setting the system

You can set the system with or without the impact sensor function. For details, see "Canceling the impact sensor" below.

1. Turn the ignition key to "LOCK" and remove it.
2. Have all passengers get out of the vehicle
3. Push the lock (set) switch on the wireless remote control key once. At this time, the turn signal lights flashes once and the security indicator light comes on.

The system is set after 30 seconds. At this time, the security indicator light start flashing slowly.

Once the system is set, you cannot start the engine until you cancel the system.

The system will not be set in the following cases.

• When any of the door is open; security horn sounds for 1 second, close the door and set the system again.
• When the hood is open; close the hood securely.

Canceling the Impact Sensor

The impact sensor can be cancelled to prevent false alarms from being triggered incase of the following conditions:

• When parked in the noisy area
• The vehicle body or glass is subjected to a strong impact from the (such as in highly pressurized car wash).
• When transporting by a car carrier or ferry.

To cancel the impact sensor;

1. Lock the door by pushing the lock (set) switch on the wireless remote control key once, and turn signal light flash once
2. Then push the lock (set) switch twice within 5 seconds. At this time, the turn signal flash 5 times to indicate the impact sensor function is disable.

The impact sensor is deactivated as long as the system remained armed.

Canceling the system

The system will be cancelled by the following two ways:

• Turn the ignition key from "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch

If the turn signal lights flash 3 times, the system has been alarmed. Check to see if there is any abnormality with your vehicle.

If any of the doors is not opened within 30 seconds, all doors will be automatically locked and the system will be set.

When the system is set

Activating the system; When the system detects abnormalities such as follows, it flashes the turn signal lights and turns on the interior light or the turn lights only (depending on the model) and sounds the security horn and vehicle horn of 30 seconds.

• Unlocking any door without using wireless control
• Any door or hood is forcibly opened.
• The battery terminal is disconnected and then reconnected.
• The system control assembly is disconnected and then reconnected
• Abnormal impact is detected when the impact sensor function is on.

Reactivating the alarm;

Once set, the system automatically resets the alarm after the alarm stops.

The alarm will activate again under the same circumstances described in "Activating the system".

Stopping the Alarm

The alarm will be stopped by the following two ways;

• Turn the ignition key from the "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch.

The system can be cancelled by these ways at the same time.

If the battery becomes discharged due to the vehicle being unused, for a long time etc., when the battery is recharged or replaced, the system will activate the alarm. If this happens, immediately unlock any of the doors by pushing the unlock (cancel) switch, and the alarm will stop.

Testing the system

1. Set the system
2. Insert a wireless remote control key into the key hole on the driver's door handle, and unlock the door.
3. Open the door, and an alarm will sound.
4. Stop the alarm by pushing the unlock (cancel) switch.
5. Repeat this operation for the front passenger's door.

Good luck.

on Nov 08, 2010 | Toyota Pickup Cars & Trucks

1 Answer

Horn wont work and gear shifter locked


is your battery dead the shifter cant move until you push down the brake.

Aug 21, 2013 | 1998 Honda Accord

1 Answer

I can not get the alarm to go off on 2002 denali


try this for me. roll the window down on the drivers side, close the door and push the lock button on the remote 2x and a chirp noise should be heard from the horns. now reach in and manually unlock the door[don't use the remote or power lock switch]and open the door. this is a test for factory alarms not aftermarket. the alarm should sound.

Jan 24, 2013 | 2002 GMC Denali

1 Answer

I had to change the battery in my 1999 camry solara. Now the car won't turn over and the factory alarm is blaring. How do I disable the factory alarm? I do not have the original key pad.


this might work...
Open hood ensure new battery is disconnected.
Open main fuse panel cover under hood and remove horn relay (so you don't have to listen to the horn).
Use the key to lock the drivers door.
Connect the positive battery terminal.
Connect the negative battery terminal (security system will now activate, hazards lights will flash and horn would be going off if the relay was not removed).
Use the key to unlock the drivers door.
Get in, close drivers door.
Use the key to start the engine.
Security system will deactivate.
Get out of vehicle, reinstall horn relay, replace fuse panel cover, close hood.

Nov 14, 2017 | 1999 Toyota Camry Solara

1 Answer

Can't make car alarm go off. had to disconnect battery


Chevy car alarms turn off with ignition and reading the transponder from the key or by turning the key in the driver door to the unlock position. If this does not turn off the alarm it maybe an aftermarket alarm. Is it a horn making noise? or is it a siren making noise? Horn usually is fatcory alarm and siren is usually aftermarket alarm. If it is aftermarket alarm then you just have to find the alrm module and unplug it.

Feb 02, 2011 | Chevrolet Tahoe Cars & Trucks

1 Answer

Alarm is going off on my vehicle and will not stop


YOU MUST UNLOCK DOOR WITH KEY AND NOT BE SO QUICK TO PULL THE DOOR HANDLE

Mar 28, 2009 | 1999 Dodge Durango

1 Answer

Alarm sounds everytime key removed from ignition?


There is a switch either in or on the driver door that turns on the interior lights and tells the module the door is open and the key is still in the ignition, this sounds the alarm, check all the doors and make sure they turn the interior lights on and off when the doors are opened and closed.

Nov 21, 2008 | 2007 Volvo V70

1 Answer

Immobilizer ?????


open the door or boot with the key
this earths the immobilizer out and will restart the alarm

Jun 22, 2008 | 1991 Nissan 300ZX

Not finding what you are looking for?
2005 Jeep Grand Cherokee Logo

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...