Question about 1999 Nissan Primera

Open Question

How do i replace a bulb in the instrument panel of a Nissan Primera

I can not remove the dashboard surrounding the instrument panel

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 25 Answers

SOURCE: primera 1996

probably has a faulty door switch...

Posted on Aug 26, 2008

Ad
  • 1 Answer

SOURCE: No instrument panel lights on 1995 Nissan King Cab

Ye, the dimmer switch still works.

I know this because, when I turn on the left direction flasher, the panel lights pulse dimly on and off with the direction light flasher.

Do I have a defective direction light flasher? if so where is it located?

Posted on Nov 25, 2008

  • 1 Answer

SOURCE: nissan primera gearbox

how much is the price for nissan primera 2003 gear box

Posted on Jan 14, 2009

  • 32 Answers

SOURCE: REPLACE C V JOINT ON NISSAN PRIMERA 1998

you will have to loosen the center nut that is located on the front hub while the care is still down on the ground to make it easy to undo then jack the car up and put it on a car stand then loosen the 6 locating nuts and bolts on the gearbox flange if it dosent have the bolts and flange it requires to use 2 leavers on both sides of the iner c v joint and pop the c v out before you try to pop the c v out you must undo the bottom lower control arm so that you can move it free if you dont undo control arm it will keep the c v sold against the fron wheel hub

Posted on Apr 12, 2009

  • 507 Answers

SOURCE: 2001 Nissan Micra replace fuel gauge bulb

need to remove instrument cluster to get to globe from the back,should be mounting screws in front to remove around instruments

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace instrument panel bulb


How to Replace an Instrument Panel Bulb - YouTube

? 14:56
https://www.youtube.com/watch?v=Rwj74yo2knY
Jun 15, 2013 - Uploaded by Schrodingers Box
Removal of an instrument panel cluster on 1996 Ford Ranger to... 1999 Ford Ranger: How to change dash board lights, walk through part 1 ...

How to Replace Dashboard Lights : Removing ... - YouTube

? 2:42
https://www.youtube.com/watch?v=zzxz7iG81kI
Sep 18, 2008 - Uploaded by expertvillage
Use socket wrench to loosen dashboard bolts. Learn about technique for installing dashboard lights in a 1996 Ford Explorerin this free auto repair series fr. ... do you need to remove the radio bezel to get to the clips?? will this ...

How to Replace Dashboard Lights : Removing ... - YouTube

? 2:30
https://www.youtube.com/watch?v=QJWoJ17liQI
Sep 18, 2008 - Uploaded by expertvillage


Dec 16, 2015 | 1996 Ford Explorer

1 Answer

Rpm backlight out


You must remove the cluter of gauges and replace the light bulb.
Instructions
    • 1Turn off the engine of the Taurus, and open the hood.
    • 2Remove the negative ("-") battery terminal from the battery in the engine compartment using a socket wrench.
    • 3.
      Insert a slotted screwdriver between the covers on the steering wheel column, and pry upwards. Pull off both the upper and the lower covers.
    • 4Position the steering wheel as low as it can go.
    • 5Remove the two screws above the Taurus' instrument panel and the four screws below it using a Phillips screwdriver.
    • 6Insert a slotted screwdriver into the dashboard trim, and pull upwards to pry it off the vehicle. Disengage the eight snap clips from the dashboard trim by hand, and pull it out of the vehicle.
    • 7Uninstall the two securing screws from the instrument panel with a Phillips screwdriver.
    • 8Pull the instrument panel towards you, and reach behind it to disconnect the two wiring plugs. Pull the instrument panel out of the Taurus.
    • 9Replace any burned-out bulbs from the underside of the instrument panel with new bulbs. Pull the old bulb off, and push the new bulb in.
    • 10Reassemble the instrument panel and dashboard trim in the reverse order of removal. Reconnect the battery, and close the hood.

Nov 06, 2012 | 2008 Ford Taurus X

2 Answers

The Check Engine light doesn't work, How do I replace it


You have to remove the instrument panel assy and replace the bulb from the back. It's not fun and it's not easy.

Feb 05, 2011 | 2001 Buick LeSabre

1 Answer

How do I remove dashboard to get to instrument panel to replace bulbs?


You will need a cross point screw driver

  • 1 Remove the two screws on the underside of the top of the trim panel surrounding the dash and instrument panel.
  • 2 Pull the trim piece off the dash.
  • 3 Remove the four screws that hold the instrument panel in the dashboard using a cross point screwdriver.
  • 4 Slide the dashboard instrument panel forward and disconnect the electrical connector from the back of the dashboard.
  • 5 Turn the instrument panel over.
  • 6 Turn the base of the dashboard light bulb counterclockwise to unlock it from the instrument panel and pull it out of the panel to remove it.
  • 7 Insert a new light bulb into the back of the panel, and turn the bulb clockwise to lock it into the panel.
  • 8 Plug the electrical connector back into the instrument panel and slide the panel back into the dashboard.
  • 9 Secure the panel with the factory mounting screws and replace the trim and trim-mounting screws using a screwdriver.
  • Nov 23, 2010 | 1999 Toyota Sienna

    1 Answer

    REPLACE DASHBOARD LENDS


    Take all the screw holding the instrument panel and slowly take it off. Now, you can change all the busted bulbs at the instrument panel.

    Nov 11, 2009 | 1999 Nissan Quest

    1 Answer

    Need to replace dashboard lamp on my 1997 Toyota


    You need to pull the instrument cluster out of the dash. This is not a very hard job, but, you can damage the outer dash fascia as it comes off, past the steering wheel.

    Move the steering wheel to its lowest position.
    Remove the phillips screws that surround the instrument cluster fascia (under the top edge)
    Pull the fascia off.
    Remove the 4 screws that holds the instrument cluster to the dashboard
    Remove the wiring connectors from the back of the cluster assembly, and pull it out. Replace the bulb, and reassemble. The wiring connectors cannot be mixed up, they are all unique.

    Nov 10, 2009 | 1997 Toyota Avalon

    1 Answer

    The instrument panel lights on my 2000 Nissan Quest have gone out. The light on the right side of the panel has been out for some time, but now the other light has gone as well. Can't see speedometer at...


    you need to buy two light bulbs from any parts store. I believe part number is 194 for the bulbs. Remove the instrument panel from the vehicle by popping the bezel loose and removing retaining screws. Once screws are out remove the instrument panel and remove the bulbs and replace them.

    Nov 08, 2009 | 1995 Nissan Quest

    1 Answer

    2001 Nissan Micra replace fuel gauge bulb


    need to remove instrument cluster to get to globe from the back,should be mounting screws in front to remove around instruments

    Oct 21, 2009 | Nissan Se R Cars & Trucks

    1 Answer

    NO LIGHT DO NOT SEE TIME


    You don't say which vehicle it is or whether the clock is built into the dashboard or is included on the instrument panel. (a) If it's built into the dashboard separately from the instrument panel, you need to remove the clock from the dashboard surround (it may just be a push-fit so if you can see the outer edges of the clock module try GENTLY using a small flat blade to ease the clock out of its receptacle). Once removed from the dashboard, disconnect the wiring plug, then look for a small bulb unit in the back of the clock module. Replace the bulb with a new one, reconnect the wiring connector and test that the clock lights up when the ignition is switched on before re-inserting the module back into its original location on the dashboard. (b) if the clock is part of the instrument panel, you will need to remove the instrument panel in order to get access to the relevant bulb (which will probably be on the rear of the instrument cluster directly adjacent to the location of the clock).

    Jul 08, 2009 | 2003 Subaru Forester

    2 Answers

    How to replace bulbs for ac/ heater control unit


    1. Remove the dash around radio (just clips)
    2. Remove 2 screws pointing up . (You do not need to remove screws which are parallel to the floor)
    3. Remove screw pointing up on the bottom of the dashboard on left side of the driver (near left leg).
    4. Remove 2 screws pointing up in the instrument cluster area.
    5. Put car in 1st gear and gently remove black plastic surrounding instruments (it will have ait vents, so slide it carefully out not to damage foam insulation on air ducts; start on the bottom hear steering column) ; unplug connectors to clock and emergency flashers.
    6. Remove 2 screws, now exposed, near instrument area, holding dashboard. (that was what I spent most time on, I didn't know about this screws.
    7. Now gently remove (or move up) dashboard (around instrument cluster and heating controls.) Start next to ignition (careful not to damage the bulb next to the ignition.
    Since you only need to get to the heating controls block, I only move up the dashboard next to it.
    8. Remove 2 screws that hold the heating control and slide heating control out . This step is unnecessary If you totally removed the dashboard.
    9. Pull out lever controls for fan speed, zone and temp
    10. Use the screwdriver (flat) to pry 2 plastic tabs on top and on the bottom of heating control so black cover can be remover.
    11. You did it! two bulbs are going to be under the cover.

    May 19, 2009 | 2001 Toyota Sienna

    Not finding what you are looking for?
    1999 Nissan Primera Logo

    Related Topics:

    350 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    76051 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    726 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...