Question about 1988 Chevrolet K1500

1 Answer

Torque specs whats the cylinder head torque specs on a 1988 chevy 350?

Posted by on

  • Anonymous Mar 17, 2014

    6 cylinder, 2 wheel drive

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 1,779 Answers

Head bolt torque is 65 ft lbs, use the below sequence, go over bolts 3x to reach final torque (not all at once to 65)

13 5 2 10
front of engine 17 9 1 6 14
16 12 8 4 3 7 11 15
good luck!

Posted on Oct 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whats the torque spec on cylinder head bolts for 1998 chevy express van 5.7L 350 v8 and it's a 1500 express


The torque specs are available in most shop manuals, but I'm sure you knew that already. There's no need to rush out and buy the shop manual if you don't want to. Go to www.autozone.com and register for free. Once registered you'll have access to repair manuals for your vehicle.

Jan 18, 2011 | Chevrolet Express Cars & Trucks

1 Answer

Need torque sttings for 350 pontiac chev 350 ,heads and intake settings


350 ENGINE CYLINDER HEAD TORQUE IS 68 FT LBS THE INTAKE MANIFOLD IS 35 FT LBS.

Jan 09, 2011 | 1988 Pontiac LeMans

1 Answer

1988 chevy 3500 i need the torque specs. and sequence for cylinder heads please .thanks


CALL THE CHEVY DEALER THEY WILL LOOK IT UP AND TELL YOU SAK FOR PARTS DEP MABEY GIVE SOME MORE TIPS

Oct 18, 2010 | 1988 Chevrolet C3500

3 Answers

Need head bolt, intake manifold, and exhaust torque specs


Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

Mar 06, 2010 | GMC Suburban Cars & Trucks

1 Answer

I have 4.9L6 need torque specs for cylinder head


for cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.


e023442.jpg

Dec 05, 2009 | 1988 Ford F 150

1 Answer

What are the torque specs for intake and head for a 1992 c 1500 chevy silverado. I need to know the torque specs for intake and head for my engine


For 1988-1995 4.3L,5.0L and 5.7L intake manifold bolts are torqued to 35ft.lbs.Start with center bolts on each side moving out finishing with the bolts in the front of the motor and the back

Oct 24, 2009 | 1992 Chevrolet C1500

1 Answer

I need to know how much pounds is apliied to a 350 chevy cylinder heads


What is the year and model of your vehicle?

On a 1968 Chevy 350 small block it is 60-70 ft/lbs with sealant applied

When torqueing the heads, it is helpful to start at around 25 ft. lbs. and torque all the bolts, then go to 50 ft. lbs., and finally, your specified torque. Doing this in increments will help give a nice even torque to the heads

Jul 25, 2009 | Chevrolet Classic Cars & Trucks

1 Answer

Need the torque specs for a 1994 350 cyl head the one with the 4 bolts through the center of the valve cover and is this the same spec for a vortec engine


  1. Tighten the cylinder head bolts a little at a time, in the sequence shown. Tighten the bolts in three stages:
    • First pass: 25 ft. lbs. (34 Nm)
    • Second pass: 45 ft. lbs. (61 Nm)
    • Final pass: 65 ft. lbs. (90 Nm)
http://www.autozone.com/addVehicleId,1938903/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528008eed5

scroll down to about half way down the page , there is step by step procedure for the 1994 5.7 L head installation and torque and tightening sequence . handy dandy site . cheers .

Jan 11, 2009 | 1988 Chevrolet K1500

2 Answers

I need the torque specs and sequence on a 1998 chevy 350 vortec


Vortecs are a little different that old school small blocks, grab a Haynes or Chiltons, the cross patterns and specs are simply diagramed. Vortec, as any really, start with 25# then 45# and then final torque which I believe is around 70-75# but to be sure verify with the manual. AutoZones, Murry's, Adavance auto all carry the books, Cheap insurance.
Dan

Nov 19, 2008 | 1998 Chevrolet C2500

Not finding what you are looking for?
Cars & Trucks Logo

789 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...