Question about 2011 Nissan Rogue

Open Question

Front wheel bearing replacement

How to replace front wheel bearing 2008 nizzan rogue

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 24 Answers

SOURCE: replace front wheel bearings

The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Posted on Jun 20, 2008

kaokensho
  • 2 Answers

SOURCE: how to replace front wheel

I can tell you on a 93 Altima that you have remove the entire wheel knuckle and press it out from the rear. Yeah, the knuckle, remove the strut tower bolts, drive train ( which can be lighty pressed out ), caliper and bracket, and remove the ball joint. There's a snap ring at the back of the wheel knuckle that holds the bearing, then press it out with a socket and a table vice or something to that effect. By the way the going commercial rate if you take it to a shop and have them do it starts at $150 for labor. Worth it, oh yeah.

Posted on Aug 15, 2008

  • 248 Answers

SOURCE: how do you replace front

To replace the front hub bearing, the whole wheel assy must be remove and press bearing out and then in.
This is a big job and u could get hurt.......

Posted on Jul 07, 2009

  • 40 Answers

SOURCE: Step by step on how to replace front wheel bearing

Raise vehicle, remove wheel, remove brake caliper, remove brake rotor remove steering knuckle by disconnecting the tie rod, ball joint, and strut. press out hub, remove snap rings press out bearing. Reassemble in reverse order.

Posted on Aug 01, 2009

NismoMaster
  • 146 Answers

SOURCE: how do you replace an in cabin micro filter on a

Remove instrument driver lower cover.
Remove accelerator pedal assembly.
Remove filter cover and then remove in-cabin microfilter.

Posted on Aug 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the ABS/VDC/AWD lights off on my 2008 Nissan Rouge not that I have replaced my left ABS Wheel speed sensor?


try this --when you start the car fist keep your foot on the brake pedal keep it on then turn the key on --if no warning lights its your brake light switch

Dec 20, 2016 | 2008 Nissan Rogue

1 Answer

How do I replace front wheel bearings on 2008


Hi, replacing the front wheel bearings on any vehicle is difficult if you don,t have the right tools, as the driveshaft and wheel hub (where the bearing is seated) needs to be removed. The hub housing the bearing may have to be heated (depending on corrosion) when the bearing is being pressed out, by using a heavy duty vice , and the new bearing is pressed in using the vice and the old bearing as a guide. I would strongly suggest you refer this repair to someone who has done this before, I personally would not undertake to change front bearings ever again, the first time for me was an experience I wouldn't want to undertake again. All the best.

Oct 15, 2014 | 2008 Subaru Tribeca

1 Answer

How do I replace front wheel bearing in a 2008 hyundai accent?


Hi there, I think from memory the whole hub assembly comes with new bearings when you replace it, it's a easy change, remove wheel, remove the brake calliper, remove the front axel nut and the hub should come off, hope this helps, it's a easy change

May 19, 2014 | 2006 Hyundai Accent

1 Answer

How can I replace front wheel bearing on my 2008 hyundai accent myself?


SKF number FW178. (or equivalent) https://www.youtube.com/watch?v=l0LCkycUcqM DON'T leave just a jack holding the car up! It's actually on stands you can't see in this video. Soft ground makes cars fall over and crush people.

May 17, 2014 | 2008 Hyundai Accent

1 Answer

Knocking in the front driver side wheel


if the knocking is only on the drivers side when you turn to the right then it sounds like you have a drivers side front wheel bearing that needs replacing. also if the bearing is bad enough you won`t have to turn much to get the noise.

Mar 06, 2014 | 2008 Cadillac CTS 3.6L

1 Answer

Humming noise wheel


Sounds like you replaced the front bearing. Could be a rear wheel bearing, or one of the tires.

Mar 01, 2014 | Chrysler Cars & Trucks

1 Answer

2008 Dodge Avenger wheel hub replacement


The front bearing comes as a hub assembly, so you should be able to unbolt it from the spindle. You still have to take the axle shaft out.

Jun 03, 2013 | 2008 Dodge Avenger

1 Answer

2008 ford explorer is making starting to make a humming sound while driving is the wheel bearing going out


Maybe jack the front of the car up and move up and down and front to back if there is a lot of play then it may be time to replace them but check both no need to just waist money that is un needed

Mar 16, 2013 | 2008 Ford Explorer

1 Answer

2008 siverado. Front-end humming. Sounds like extremely loud tire pattern noise coming from left-front wheel area, noise stops when i turn the steering wheel to the right. replaced tire with no results.


it is your wheel bearing. the bearing is a sealed unit so you replace the hub assembly. remove wheel,caliper,brake rotor.if it is 4x4 loosen axle nut. there are three 15mm bolts on back side of spindle remove these and slide hub out replace with new one. most hubs come with new wheel speed sensor so remove harness from connectors or if no new one remove the screw holding it in place to hub and slide out.

Dec 31, 2010 | 2008 Chevrolet Silverado 1500

2 Answers

Have 44k on a 2008 chevy uplander. Front left


I have a 2008 as well.. with 39K and the front right needed replaced.
it was covered under the 100K warranty

Mar 19, 2010 | 2008 Chevrolet Uplander

Not finding what you are looking for?
2011 Nissan Rogue Logo

Related Topics:

551 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...