Question about 2000 Chrysler LHS

1 Answer

How to remove fog lites 2000 chrysler lhs - 2000 Chrysler LHS

Posted by on

  • Jeremy W.
    Jeremy W. Feb 16, 2012

    are you replacing the lens assembly or just the bulb?

  • bud petralia Feb 17, 2012

    i am replacing the entire fog lite assembly

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 5,332 Answers

Remove the splash shield under the front bumper. You will see the mounting screws for the fog lamps.

Posted on Feb 17, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
bunnydawg
  • 5158 Answers

SOURCE: where is the starter on a 2000 chrysler lhs?

I can't tell you what side it's on.... but it is where the motor joins to the transmission. if it is front wheel drive (the motor is sideways). look down about the middle of the engine where it joins the transmission.... that is your starter. you should be able to follow one of the large wires from the battery to it. speaking of which make sure you disconnect the battery before changing the starter.

Posted on Apr 15, 2009

  • 226 Answers

SOURCE: Chrysler LHS Starter

The starter is located beneith the engine, near the transaxle and it is attatched to the engine by 3 bolts. You need to disconnect the battery, raise the car to get at it. The 3.3 and 3.5 engines take different starters. Rick

Posted on Apr 15, 2009

  • 1 Answer

SOURCE: replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?

I had the same problem. My Chrysler LHS kept overheating. I had the thermostat changed out first and it didn't help. Then I had the water pump changed out and still did no good. Then changed out the radiator, still overheated. Come to find out the people that changed my thermostat put it in backwards. Evidently, the thermostats for these cars look different from all the others and people are not sure how to put them in. I took mine to a Chrysler dealer and they fixed it for me.

Posted on Apr 15, 2009

CMV9
  • 594 Answers

SOURCE: HOW TO REPLACE HEADLIGHTS ON

ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Posted on Apr 16, 2009

  • 14036 Answers

SOURCE: replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?

fix the radiator first.because coolant temperature sensor need to be in antifreeze.when antifreeze get up to 190 degrees. the coolant sensor act as a thermostat.it resistance decrease then the pcm will command cooling fans to run.if antifreeze low the coolant temperature sensor not going to work. engine is going to over heat.

Posted on May 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Chrysler LHS 2000 is leaking fuel somewhere. smells inside the car and out of gas when running. Is it a hose?


cud be the tank also or other-get it to a shop that does a leak test-they use a dye then a detector lite--check yourself under car and hood for bad connections--follow any wet areas or try to target a smell

Oct 04, 2014 | 2000 Chrysler LHS

1 Answer

Where is the termostat located on my 2000 chrysler lhs


Hi your thermostat is situated below the alternator at the end of the rubber hose. You will have to remove it from under the car or through the fender. It will also help to remove your alternator for more hand room from the top if you have a helper holding the part for you to screw the upper bolt. Make sure you apply the new gasket properly. Mike

Sep 19, 2010 | 2000 Chrysler LHS

1 Answer

Just curious as to how i get to my 6x9s in my 2000 LHS


first you need to remove the pillars then remove seatbelts then remove headrest then remove the back of rear break light then you can take off the rear dash then you can change them

Oct 26, 2009 | 2000 Chrysler LHS

1 Answer

Replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?


fix the radiator first.because coolant temperature sensor need to be in antifreeze.when antifreeze get up to 190 degrees. the coolant sensor act as a thermostat.it resistance decrease then the pcm will command cooling fans to run.if antifreeze low the coolant temperature sensor not going to work. engine is going to over heat.

May 29, 2009 | 2000 Chrysler LHS

2 Answers

Replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?


I had the same problem. My Chrysler LHS kept overheating. I had the thermostat changed out first and it didn't help. Then I had the water pump changed out and still did no good. Then changed out the radiator, still overheated. Come to find out the people that changed my thermostat put it in backwards. Evidently, the thermostats for these cars look different from all the others and people are not sure how to put them in. I took mine to a Chrysler dealer and they fixed it for me.

Apr 15, 2009 | 2000 Chrysler LHS

1 Answer

Change brake light 2000 lhs


The rear lenses can be removed by opening the trunk, remove the possible liner that covers the hex nuts on on the lamp housing behind the lens assembly and remove them, remove electrical connector and replace bulb.

Mar 16, 2009 | 2000 Chrysler LHS

2 Answers

How do you replace the headlight bulb on a 2001 chrysler lhs.


This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Jan 28, 2009 | 2000 Chrysler LHS

1 Answer

HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS


ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Jul 28, 2008 | 1994 Chrysler New Yorker

Not finding what you are looking for?
2000 Chrysler LHS Logo

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...