Question about 2008 Nissan Titan

1 Answer

Where is the water pump located on a 2008 Nissan Titan

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 5,332 Answers
Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Brian032472
  • 150 Answers

SOURCE: blower for nissan titan

The picture I will try to attach will show you the blower motor housing. The white electrical harness rt hand upper corner is attached to the blower motor resistor. If you have checked the relay and its working ( you can check with a tester) the resistor is probably the problem. It's the most common a/c blower issue I see weekly hope I can send it and hope it helps.

Posted on Nov 08, 2008

NismoMaster
  • 146 Answers

SOURCE: How do you fix the water pump on a 1997 nissan

The water pump is located behind the timing chain cover. There are two black plates on the front cover. The one near the front of the car has the water pump behind it. The other one has the timing chain tensioner behind it. First you must drain the coolant. Then support engine and remove engine mount. Then remove drive belts. Then remove the two black plates. Push the tensioner in and lock it with a paper clip. Then remove the two bolts holding the tensioner and remove tensioner. Then remove the water pump bolts. Rotate engine crankshaft the take tension off of water pump (about 20 degrees). Then install two bolts into water pump threaded flange (M8). Tighten M8 evenly as water pump will come without damaging it. Check for corrosion. Then replace with new one. Make sure you use new "O" rings. Lubricate with engine oil. Put the original three bolts back in the water pump. Then install timing chain tensioner and black covers. Replace belts and engine mounts. Add coolant and pressure test system.

Posted on Sep 07, 2009

ZJLimited
  • 17970 Answers

SOURCE: Replacing the mirror lens only

Remove the triangular cover lining.
A) Disengage the wiring connection and insert the male end of the connector back inside door frame so it can easily be removed.
B) Caution: Be careful not to drop the mirror housing. Secure the mirror housing with one hand, remove the (3) nuts holding the mirror housing to the door frame using a 10mm socket.

Carefully remove mirror housing from door frame and set mirror housing on a cloth covered surface.

C) Push down on the upper inboard edge of glass until mirror pivots fully outward. Insert a large slotted screwdriver in between the slotted hole. Carefully pry and twist screwdriver until original mirror pops off. If heated, disconnect heater wires from heater terminals and remove mirror.

Hope helps.

Posted on Oct 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does it have a fuel kill reset button and, if so, where is it located?


From what I've looked up, I'm not sure it has one. Are you experiencing starting problems? Might be the fuel pump relay. If so that is located under the hood, usually on the driver's side. Black box that has fuses/relays. Hope it helps.

Sep 01, 2015 | 2008 Nissan Titan

1 Answer

2008 Nissan titan cranks but no start no cumin ovation with ECM check fuses and fusible links all checked out good fuel pump is good but doesn't come on


Nissan had a problem with the circuit board in the main fuse block getting a crack in it and creating the no start condition. IDPM is the name that Nissan calls the part.

Nov 07, 2014 | 2008 Nissan Titan

1 Answer

How to tell the intake cam from the exhaust cam o my 2008 Nissan titan


There should be a letter "E" for the exhaust side, and an "i" for the intake !
Sometimes barely visible !

Oct 03, 2014 | 2008 Nissan Titan

1 Answer

Timing chain diagram for nissan titan 2008 5.6 ?


If you are taking on such a huge job as a head gasket on a Titan, why oh why didn't you MARK EVERYTHING.

Sep 14, 2014 | 2008 Nissan Titan

2 Answers

Titan turns over but does not start


Titans have had an issue with a relay in the IPDM(fuse block), when I was at Nissan we replaced about 3-4 a week for the same problem.

Feb 03, 2013 | 2008 Nissan Titan

1 Answer

Do 2008 nissan titan power steering pressure hoses have restrictors


You had leaking hoses replaced & now you
have other issues?

Some shop you went to

Sounds like it is low on fluid or the
pump is whining

When you can't take the noise anymore,
replace the pump

Have to use the correct fluid,maybe that
wasn't done as well

The Steering Rack may have failed from no
fluid changes every 3 years & that is your
restriction,not the hoses,rack may be bound

Oct 03, 2012 | Cars & Trucks

1 Answer

I have to change the oil pump of my 2004 titan


BEHIND THE TIMING COVER ON THE CRANKSHAFT

Mar 14, 2010 | 2004 Nissan Titan

Not finding what you are looking for?
2008 Nissan Titan Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...