Question about 1987 Ford Ranger

1 Answer

Vaccum hose diagram for 1987 ford ranger needed

Working on a friends ranger and finding many vaccum hoses not attached, could use some help with a diagram

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

CHeck this diagrams...


vaccum hose diagram for 1987 ford ranger needed - 2_16_2012_2_02_19_pm.jpg


Fig. 14: Vacuum hose routing-1987 2.9L engine - zoom link here


2_16_2012_2_05_56_pm.jpg

Fig. 13: Vacuum hose routing-1987 2.3L engines - zoom link here

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Feb 16, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 124 Answers

SOURCE: 1987 Ford Ranger 2.0 Liter Vacuum Line Diagram

can you see the diagram under the hood? if not try searching a junkyard for either the diagram or a complete motor

Posted on Mar 23, 2009

junkman1249
  • 552 Answers

SOURCE: hoses are leaking

one at a time. after you install them make sure you turn the car on and move the steering wheel left to right several times to let the fluid circulate into the pump. you hear a strange noise but it will go away

Posted on Dec 13, 2008

canbruce75
  • 1776 Answers

SOURCE: I need a diagram for where the vacuum hoses go to

Check out the autozone.com website and register the truck there. It doesn't cost anything and will give you access to an online repair manual for the truck. The vacuum diagrams should be available there. Hope this helped and best wishes.

Posted on Aug 30, 2009

  • 87 Answers

SOURCE: need vacuum hose diagram for 2001 ford ranger with

fb904d6.gifhere it is good luck!

Posted on Mar 08, 2010

  • 172 Answers

SOURCE: ford taurus v6 duratec vacuum hose diagram

under the hood is a vacum diagram

Posted on Apr 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 ford ranger vacuum hose diagram


1999 Ford Ranger Vacuum hose diagram
Pamela, Normally vacuum line routing can be found under the hood of truck, on Rad support or on the underside of hood. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Ford Ranger Engine Vacuum Hose Diagrams
Vacuum Lines The Ranger Station Forums
Repair Guides Vacuum Diagrams Vacuum Diagrams AutoZone com

Jun 12, 2016 | 1999 Ford Ranger SuperCab

1 Answer

Need to know locations of Vaccum hoses on 2002 ford Econo Van 2.0ltr motor fe model


google images for your : 2002 ford Econo Van 2.0ltr motor fe vacuum hose diagrams.

Mar 12, 2015 | 2002 Ford Econoline Cargo

1 Answer

What i need is a 1989 ford ranger 2.3l engine vacuum hose diagram?


Is it a vacuum hose? Find the open hole in the plenum (you should hear a pronounced hissing sound with the engine running). THAT is where the hose goes.

Jul 22, 2014 | 1989 Ford Ranger

1 Answer

Several vaccum hoses are not attached, I need a diagram for a 1987 ford ranger


Hi John:
I suggest to check this diagrams...


2_16_2012_2_02_19_pm.jpg



Fig. 14: Vacuum hose routing-1987 2.9L engine - zoom link here


2_16_2012_2_05_56_pm.jpg


Fig. 13: Vacuum hose routing-1987 2.3L engines - zoom link here

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 16, 2012 | 1987 Ford Ranger

2 Answers

How do i change the heater core on a 1987 ford ranger v6 2.9 liter..from the inside or outside under the hood


you are going to drain and loosen the heater hoses from under the hood, the rest is inside. get yourself a repair manual cheap on ebay. you are lucky in that you have no passenger airbag and most likely you can do this yourself.

Dec 15, 2010 | 1987 Ford Ranger

1 Answer

I have a ford ranger and the diagnostic code coming up is p1400 evg low voltage...ranger is 1998...


Ok.. The code P1400. Is. Related with the E.G.R system.
" Exaust Gas Recirculation"
The code P1400 is Exactly.
Sensor DPFEGR low voltage.
This code can set for.
Leaking up-strim pressure hose.
DPFEGR sensor Short to ground or signal return circuit.
VREF selenoid shorted to ground or signal return circuit.
Faulty DPFEGR .
or In the last case faulty PCM.

Ok.. The DPFEGR is a little box Located at the intake manifold.
to identificate See the Exaust Manifold Gasket you will see.
2 Little hoses Goin at the little box. When you found.
Check the hoses for cracked or damaged repair as need.
Check the connector.
The VREF. to locate follow the Little vaccum hose GREEN.
Goin to the EGR attached at the Intake manifold .
and check the connection.
If everything is OK. I recomend to replace the DPFEGR.

NOTE. If you don't have enought Expertise on vehicles.
I recomed to consult with your mechanic. and maybe give this information.
But if you can do your self go ahead.

I hope this help on your question. THANK YOU FOR USE FIXYA..

Dec 01, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Where cN I FIND A DIAGRAM FOR THE COOLANT SYSTEM ON A 1987 FORD 460


Many auto parts stores carry maintenance and service manuals for the 1987 Ford vehicles. Don't recall seeing a "diagram" of a "cooling system" though. There isn't much to it...a radiator, outlet hose to engine block, inlet hose from engine block to radiator with a thermostat installed. Problems...thermostat can stick, radiator can corrode up, leak in radiator can occur, engine water jacket can rust up. Routine maintenance and antifreeze solution can help keep the radiator working fine.

Jun 03, 2009 | 1987 Ford Econoline

1 Answer

1987 Ford Ranger 2.0 Liter Vacuum Line Diagram


can you see the diagram under the hood? if not try searching a junkyard for either the diagram or a complete motor

Mar 23, 2009 | 1986 Ford Ranger 2WD

1 Answer

Vaccum hoses


there should be a diagram either on the underside of the hood or on the radiator support, if that fails I would go to http://www.rangerpowersports.com/ and see about finding pictures of the needed lines or perhaps picking up a FSM for your truck from Ebay, they usually don't cost more then 20-40 dollars and if you are serious about doing your own mechanic work it is invaluable

Oct 11, 2008 | 1992 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

1,752 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...