Question about Hyundai Cars & Trucks

Open Question

What size bolt goes to a hyundai elantra starter

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: alternator removal on 2001 Hyundai Elantra

All I did was wiggle the bolt out . You have to loosen the power steering pulley and bracket and remove the fan shroud on the left side.

Posted on Jun 18, 2009

  • 94 Answers

SOURCE: How to replace 2004 Hyundai Elantra starter

First, disconnect the battery. Then the only part that needs to be removed to access the starter is the rubber air plenum boot between the throttle body and the air filter housing. This allows enough room to get an arm in there to access the 14mm bolts that attach the starter to the transmission. After removing the bolts, the starter can be removed from underneath the car. lower it down as much as possible, and unbolt the power cable. You may have to twist and turn it a bit to get around the support between the engine block and intake manifold, but it will come out.

Posted on Feb 07, 2010

  • 181 Answers

SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS

You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Posted on Feb 19, 2010

ZJLimited
  • 17970 Answers

SOURCE: Where is my starter and how do I change my starter?

2000 Hyundai Elantra 2.0L MFI DOHC 4cylRemoval & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Speedometer and shift control cables Starter electrical connectors Starter motor
  3. 2e15922.jpg

    Fig. Exploded view of the starter-XG 300 and XG 350

To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 25 ft. lbs. (34 Nm) Starter electrical connectors Speedometer and shift control cables Negative battery cable
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Air intake assembly Speedometer cable Shift cable Starter wiring connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 20-25 ft. lbs. (26-33 Nm) Starter wiring connectors and torque the battery cable nut to 88-140 inch lbs. (10-16 Nm) Shift cable Speedometer cable Air intake assembly Negative battery cable
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Air intake assembly Speedometer cable Shift cable Starter wiring connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 20-25 ft. lbs. (26-33 Nm) Starter wiring connectors and torque the battery cable nut to 88-140 inch lbs. (10-16 Nm) Shift cable Speedometer cable Air intake assembly Negative battery cable
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Speedometer and shift control cables Starter electrical connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 25 ft. lbs. (34 Nm) Starter electrical connectors Speedometer and shift control cables Negative battery cable.

All Others
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable and wait at least 3 minutes Speedometer cable and shift cable from the transaxle Starter motor wiring Starter motor bolts and the starter
To install:
  1. Installation is the reverse of removal. Tighten motor retainers to 20-25 ft. lbs. (27-34 Nm).

Hope helps (remember rated this).

Posted on Jul 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What size caliper bolt in a 2009 Hyundai Elantra?


12 mm ,14,mm wrench or socket that to remove the caliper 17 mm wrench or socket for the bolt holding the brake pad braket

Mar 14, 2015 | Hyundai Cars & Trucks

1 Answer

Hi I would like to kw if a hyundai elantra j1 1994 model starter is the same like a hyundai sonata 1995 starter


Hi Warren, I had a 1995 Elantra and they were very good at reusing their tehnology on all their models. What engine size are you talking about here. Mine was 1600 GLS but there was a 1800 GLS as well. On the Sonata some had bigger engines which may have required stronger starter motors, so please check first.

Nov 14, 2014 | Cars & Trucks

2 Answers

Where do wires from battery go to on 98 elantra


the positive lead has the larger terminal on it as the battery posts are different sizes. the small terminal goes on the small post and the wire runs to the engine or body as the earth .. Positive leads are coloured red while negative leads are black.

Apr 13, 2014 | 2001 Hyundai Elantra

2 Answers

Where is the starter located on a 2006 hyundai elantra


LOOK UNDER AIR FILTER.ITS BOLTED TO SIDE OF ENGINE NEXT TO TRANSAXLE.

Apr 11, 2010 | 2006 Hyundai Elantra

1 Answer

Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS


You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Feb 19, 2010 | 1997 Hyundai Elantra

1 Answer

How to replace 2004 Hyundai Elantra starter


First, disconnect the battery. Then the only part that needs to be removed to access the starter is the rubber air plenum boot between the throttle body and the air filter housing. This allows enough room to get an arm in there to access the 14mm bolts that attach the starter to the transmission. After removing the bolts, the starter can be removed from underneath the car. lower it down as much as possible, and unbolt the power cable. You may have to twist and turn it a bit to get around the support between the engine block and intake manifold, but it will come out.

Feb 05, 2010 | 2004 Hyundai Elantra

1 Answer

How do I remove the broken bolt in the alternator of my Hyundai Elantra 2001?


This is tricky because the end of the bolt threads into the alternator bracket. You probably will need to use a bolt extractor kit, available from most hardware stores. However this requires you to drill a starter hole into the broken end of the bolt, which might be difficult to access. As an alternative you can drill the starter hole into the threaded end, and back it out from that direction. .

Jan 19, 2010 | Hyundai Motor 1999 Elantra

2 Answers

2000 hyundai elantra alarm goes off where is the


There is NO kill switch on the 2000 Elantra... HOWEVER, there is a thing called the Key Fob (keyless remote entry system). There is, however, a system in place called the 'starter kill' circuit and it is activated when the burglar alarm goes off.... it's called the burglar alarm relay and it is activated to prevent the engine starter system from being used. There are three ways to get the engine started in such a circumstance... 1. use the key fob to 'disarm' the system... 2. put the key in the ignition and turn it to the 'RUN" position and wait until the alarm stops (horn stops beeping and the parking lights stop flashing), then the engine will start.... 3. pull the starter relay from the UnderHood junction box and bypass the starter circuit (key in ignition and in the 'RUN' position), jumper the starter solenoid circuit to energize the solenoid to start cranking the engine -- it should start then.

Oct 03, 2009 | 2000 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...