Question about 2001 Cadillac DeVille

Open Question

Torque spec 2001 cadillac seville outer tie rod

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: Replace tail lights

Usually all you have to do is pull back the inside trunk liner behind the tail lights from inside the trunk, or there may be a plastic door that you open to access the tail lights. The wires going to the tail lights connect to a plug that you turn counter clockwise and pull out from the back of the tail light assembly. Once you have removed the connector replace the bulb. Some light bulbs just pull straight out of the connector, others you may have to push in and turn counter clockwise to remove.

Posted on Jan 17, 2009

  • 135 Answers

SOURCE: Need to replace both crankshaft position sensors 2001 Cadillac

4.6 the twocrankshaft position sensors are located on the front of the block just above and to the left of the oil filter. not hard to replace.

Posted on May 19, 2009

  • 22 Answers

SOURCE: 2001 Cadillac Deville TCC PWM Solenoid Circuit (p1860)

it should take approximately 4 - 5 hours plus the cost of sensor

Posted on Aug 25, 2009

  • 432 Answers

SOURCE: what type of power steering fluid is recommended

GM from any GM dealer.

Posted on Oct 11, 2009

csmock132
  • 4669 Answers

SOURCE: what are the cylinder head torque specs for a 1999

I can help you with this but I have to ask one question. Have you already taken this apart and putting it back together? Did you rethread all the head bolt holes because they strip out when you tighten them and you will ruin the head gaskets. Let me know, I have don't this job quite a few times. I'll have to look up the actual torque specs. Also you are wanting the spec for the cylinder head bolts and not the cylinder head cover bolts right?

Posted on Jun 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for outer tie rods Chrysler Pacifica 2008


For the lock nut at the rack or for the tie rod end to steering knuckle?

May 19, 2017 | 2008 Chrysler Pacifica

1 Answer

Torque specs outer tie rod 2002 pt cruiser


Tighten it up using 2 spanners as tight as you can .

Sep 11, 2016 | 2002 Chrysler PT Cruiser

1 Answer

What are the torque specs on a 2007 Jeep Compass. Front axel nut and tie rod end?


Axle nut=180 foot pounds Outer tie rod nut= 97 foot pounds

Nov 15, 2015 | Jeep Cars & Trucks

1 Answer

What is the torque for inner tie rod end on a 2000 for focus


59 ftlbs

Hope this will answer your question,If do pls click on helful botton and you can follow me at fixya,so I can answer your question faster.thanks.

Mar 10, 2015 | 2000 Ford Focus

1 Answer

HOW TO CHANGE A STEERING RACK


Involves disconnecting the outer tie rod ends. Steering linkage from steering wheel. Disconnecting the power steering pump lines and unbolting the rack and pinion from the body.
Look at the new one for bolt locations. Make sure the new one comes with new tie rods or you might be back under there again too soon.

Apr 18, 2013 | 1999 Cadillac Seville

1 Answer

Tire rod end left sidefrom gearbox is broken how do i dismantel


if its the outer tie rod than loosen the jam nut on the threaded part of the inner tie rod. You will then be able to unthread the outer tie rod from the inner. Count the number of turns and install the new one with the same number of turns.

If its the inner tie rod you will need an inner tie rode remover/installer tool and a torque wrench.

Feb 03, 2012 | 2001 Mercury Sable

1 Answer

2006 grand caravan sxt 3.8 liter outer tie rod torque specs needed please.


Hello billmarks: My name is Roger and I will help you. The torque specs for the tie rod lock nut and the tie rod spindle nut is 55 foot pounds. Should you need further help please just ask.Please rate the answer. Thank You for using Fix Ya. Roger

Sep 08, 2010 | 2006 Dodge Grand Caravan

1 Answer

Torque specs. for outer tie rod ends for 2006 dodge ram 1500 quad cab 4x4, 5.7 hemi


Tie rod end is 35 ft. lbs. Pinch bolt for the lower ball joint - 105 .I hope this helps you

Oct 06, 2009 | 2006 Dodge Ram

1 Answer

Need torque spec for 2000 Cirrus outer tie rod ends


45 Ft-lbs Tie-rod balljoint stud-to-steering knuckle nut, and 55 Ft-lbs Tie-rod (outer)- to- inner jam lock nut

Apr 04, 2009 | 2000 Chrysler Cirrus

Not finding what you are looking for?
2001 Cadillac DeVille Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...