Question about 2001 Kia Spectra

1 Answer

Where is the location of the tmc 0n a 2001 kia spectra located

Location of tcm on the car

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 48 Answers

IF ITS NOT NEAR ONE OF THE REAR WHEELS LOOK NEXT TO TRAMSMISSION

Posted on Feb 16, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

turboKia
  • 55 Answers

SOURCE: kia spectra starter

It is attached to the bell housing on the drivers side. The starter is located in the back of the engine, under the intake manifold.

Posted on Aug 21, 2009

  • 336 Answers

SOURCE: location of the thermostat & water pump on a 2005 kia spectra

Hi there,

Please see below exploded diagram regarding location of thermostat and water pump.

04e2671.jpg

5f32ab7.jpg



Regards,
Jeep Brainy

Posted on Sep 18, 2009

BCAS1298
  • 3092 Answers

SOURCE: timing belt diagram for a 2001 kia spectra 16 v

Hope this helps you.

d4eae93.gif5811782.gif23bb7eb.gif

Posted on Jul 23, 2010

Testimonial: "Wow that was a fast response. Thank you very much and have a wonderful day!!"

fastboyz
  • 674 Answers

SOURCE: locating and replacing the o2 sensor on a 2005 kia spectra

a wrench and just unplug the sensor wire and screw out and install new one. they make a special socket but i just use a wrench.

Posted on Sep 11, 2008

  • 98 Answers

SOURCE: Changing the starter on a Kia Spectra

Here's step-by-step instructions on how to access, remove and re-install your alternator. Hope it helps! Have a great day!

Alternator Kia_Sephia_Rio_Spectra_Optima_1998-2006

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  4. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  5. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  6. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  7. Remove the power steering pump, 2.0L engine only.
  8. Remove the power steering pump bracket, 2.0L engine only.
  9. Remove the alternator B terminal cover cap.
  10. Disconnect the alternator electrical connections.
  11. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  12. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  13. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump, 1.6L (VIN 3) engine only.
  15. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  16. Remove the alternator tensioner mounting bolt and the belt tensioner.
  17. Remove the alternator pivot bolt.
  18. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  19. Remove the alternator. 0900c15280028419.jpgAlternator mounting—1.5L and 1.6L (VIN 5) engine shown 0900c1528002841a.jpgAlternator mounting—2.0L and 1.6L (VIN 3) engines shown 0900c1528002841b.jpgAlternator mounting—2.4L and 2.7L engine
To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).
  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).
  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).
  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).
  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.
 

Posted on Nov 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the location of the T.M.C in the Isuzu-08 pickup Transmission What is the location of the T.C.M in the 2008 Isuzu Transmission


i-290 or i 370?????? its not an asunder.
you are H3LL bent on find this box. TCM , not TMC.
why post 2 times same question, why?\
USA car?
and why assume its a separate box, why>?
never assume that.

there were 3 transmissions
4L60, 4L65, and 4L70-e , all for are dash E(electric shifted)

now guess 10
The transmission control module (TCM) (5.3L only) is mounted near the lower left front of the engine and connects directly to the engine wiring harness

some do have seperate TCM ,
but why not scan the car first
and not risk damaging a vary expensive module.
leave it be.
scan it.
check fuses first and levels ATF.

Dec 03, 2015 | Isuzu Cars & Trucks

1 Answer

Where is knock sensor located - on 2001 kia spectra.


Its located under the intake manifold at the top of the engine block.

Mar 02, 2015 | 2001 Kia Spectra

1 Answer

Location tcm


im trying to locate transmission control module

Jan 08, 2014 | 2002 Kia Spectra

1 Answer

Tcm


either by left rear or right wheel

Feb 15, 2012 | 2001 Kia Spectra

1 Answer

Ineed to know where kia spectra knock sensor location is


The knock sensor is placed on the engine block under the intake manifold.

May 31, 2011 | 2001 Kia Spectra

1 Answer

Location of knock sensor in 2004 kia spectra vehicle


Where is the knock sensor located on a 2004 kia spectra?

Sep 27, 2010 | 2003 Kia Spectra

1 Answer

Kia spectra starter


It is attached to the bell housing on the drivers side. The starter is located in the back of the engine, under the intake manifold.

Jul 15, 2008 | 2002 Kia Spectra

Not finding what you are looking for?
2001 Kia Spectra Logo

Related Topics:

269 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...