Question about 2011 Audi Q5 2.0

Open Question

Q5 5 rear washer

Rear washer does not spritz. How do I remove the rear blade to check for clogs or a detached hose?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where do I add washer fluid for rear window wiper on a 2000 blazer


Open the hatch and look for the fill cap along the sides .

Oct 23, 2015 | Cars & Trucks

1 Answer

How to re attach supply hose to back window in T & C 2007


if the washer pump is working for the rear then you will have to remove the rear door interior panel and check the hose for a blockage and check and clean out the spray nozzle for the rear window. sometimes they get plugged and need cleaning.

Sep 18, 2014 | Chrysler Town & Country Cars & Trucks

1 Answer

Front washer motor not engaging, rear washer works


washers.
hits electric and water hydraulics, so 2 technologies merge.
1: fuses blown?
2: does pump motor spin when asked, (2 men or kit and you)
yes, good
no, ? bad, pull hose, spin now,
yes, line clogged
no? pump dead, or clogged clean pump or replace, your call.
if pump seems dead i check for 12vdc at pump on demand.
kid turns switch and 12vdc lands on motor pins.
got 12v, good.
so pump spins, and no squirt.
A: the line is long, very long. and can clog easy due to that fact
or the jet on the end is clogged.
so why no remove the hose. does the hose squirt on demand.? at rear of car>?
yes, nozzle clogged.
no,,, line clogged. big work finding long hose line.
some lines near front of car (hoses) have check valves.
they too love to clog.
there you go, washer 101.

Dec 16, 2013 | 2007 Toyota Highlander

1 Answer

I have a 2003 Envoy XL the rear windshield wiper works but the rear washer won't work


{: ) The rear washer pump is attached to the washer fluid reservoir. Below the left headlamp assembly. Ignition on, engine off. Switch ON the rear washer control. If you can hear the rear washer motor works, check for clogged hoses and tubes. If it's not clogged, your motor could only be running but not pumping.
If you cant hear the washer motor at work, its probably faulty.
To rule out if its a control switching issue, get a test light to check for voltage at the washer connector if you could only access it. Its better to check on that end. If you cant access it, at least probe the rear washer fuse at the underhood fuseblock. The test lamp should light everytime you switch on the rear washer switch.

Feb 03, 2011 | 2006 GMC Envoy

2 Answers

How do I fix my window washer pump on my 2000 dodge caravan?


One can get a repair kit that includes a new motor pump and wiring clips, or

one can get the original motor that plugs into the windshield wiper fluid reservoir.

---
Windshield wiper reservoir (gives idea of how to change the windshield wiper fluid pump motor) Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and splash shield.
  4. Disconnect the electrical connectors from the pumps and detach the rear washer hose.
  5. Place a drain pan under the reservoir if it contains fluid.
  6. Disconnect the front washer hose at the wiper unit in the engine compartment. NOTE: The front hose will be removed with the reservoir.
  7. Let the fluid drain from the reservoir.
  8. Remove the mounting screws and the reservoir.
To Install:
  1. Install the fluid reservoir with the mounting screws.
  2. Connect the front washer hose in the engine compartment.
  3. Connect the electrical connectors and rear washer hose.
  4. Install the splash shield.
  5. Install the right front wheel.
  6. Lower the vehicle.
prev.gif next.gif

Aug 27, 2010 | 2000 Dodge Caravan

1 Answer

Where is windshield wiper motor for 1992 mercury grand marquis


1992-98 Vehicles
  1. Disconnect the negative battery cable.
  2. Remove the rear hood seal. Remove the wiper arm assemblies by raising the wiper blade off the windshield. Move the slide latch away from the pivot shaft and slowly lower the arm onto the latch. This unlocks the arm from the pivot shaft and holds the blade off the glass. Pull the arm from the pivot shaft.
  3. Remove the cowl vent screws and disconnect the washer hoses from the washer jets.
  4. Detach the electrical connectors from the wiper motor.
  5. Remove the wiper assembly attaching screws, lift the assembly out and disconnect the washer hose.
  6. Unsnap and remove the linkage cover.
  7. Remove the wiper module assembly retaining bolts and remove the module from the vehicle.
  8. Remove the linkage retaining clip from the motor operating arm by lifting the locking tab and pulling the clip away from the pin.
  9. Remove the motor retaining screws and remove the motor from the vehicle.
  10. The installation is the reverse of the removal.

ad37f8d.jpg

Fig.: Lift up to release the clips and remove the hood-to-cowl weather strip


ca6ea0f.jpg

Fig.: Remove the cowl panel-to-firewall retaining clips



Remove the driver's side then the passenger side cowl panel from the vehicle


d57f264.jpg



Fig.: Detach the electrical connector for the wiper motor

Release the wiper motor retaining clips and remove the cover from the vehicle


ffed3a6.jpg



Fig.: Remove the wiper module assembly retaining bolts and remove the module from the vehicle


412221d.jpg



Fig.: Remove the wiper motor retaining bolts and ...


46edc09.jpg


Fig.: ...remove the wiper motor from the vehicle




Hope helps (remember comment and rated this).

Aug 02, 2010 | 1992 Mercury Grand Marquis

2 Answers

Cylinderhead torque stc.


Cylinder Head Removal & Installation SOHC To Remove:
  1. Relieve fuel system pressure.
  2. Remove timing belt cover. Camshaft timing marks kia-03-20-7032.gif

  3. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  4. Loosen lock bolt on tensioner.
  5. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt.
  6. Remove timing belt from camshaft pulley.
  7. Disconnect battery negative cable.
  8. Remove 3 bolts that secure accelerator cable and air intake hose to cylinder head cover.
  9. Detach accelerator cable and place off to side.
  10. Remove the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  11. Disconnect mass air flow sensor electrical connector.
  12. Remove air intake hose.
  13. Remove PCV valve from cylinder head cover.
  14. Remove ISC air hose from idle speed actuator.
  15. Remove air hose from behind intake manifold.
  16. Remove 2 screws from high tension wire protectors.
  17. Detach wire loom from holder at rear of cylinder head cover.
  18. Detach vacuum tube at rear of cylinder head cover.
  19. Remove vacuum pipe. Cylinder Head Cover kia-03-20-7042.gif

  20. Remove 7 cylinder head cover bolts.
  21. Remove cylinder head cover and gasket.
  22. Disconnect 2 ignition coil electrical connectors.
  23. Disconnect 2 fuel injection electrical connectors at rear of cylinder head.
  24. Disconnect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  25. Disconnect heater hose from elbow.
  26. Disconnect brake booster vacuum hose and cruise control vacuum hose from surge tank.
  27. Detach wire harness from rear of cylinder head.
  28. Disconnect purge control solenoid vacuum hose from intake manifold.
  29. Disconnect fuel hose from fuel connector assembly.
  30. Remove grounding bracket.
  31. Remove 4 bolts and intake manifold bracket.
  32. Remove starter.
  33. Detach water bypass hose from bypass pipe.
  34. Disconnect water hoses from oil cooler.
  35. Disconnect fuel hose from fuel pipe.
  36. Remove exhaust manifold heat shield.
  37. Remove exhaust flange nuts and front exhaust bracket bolt.
  38. Lower exhaust system. Cylinder head bolt loosening sequence kia-03-20-7050.gif

  39. Loosen cylinder head bolts in 3 steps in proper sequence.
  40. Remove cylinder head bolts and washers.
  41. Remove cylinder head, intake manifold and exhaust manifold as an assembly.
To Install:
  1. Install NEW cylinder head gasket.
  2. Install cylinder head, intake manifold and exhaust manifold as an assembly.
  3. Tighten cylinder head bolts in 3 steps in reverse sequence that was used during removal. Tighten bolts to 62 ft lb (84 Nm).
  4. Install front exhaust bracket bolt. Tighten bolt to 20 ft lb (27 Nm).
  5. Install NEW lower exhaust flange gasket and 3 nuts. Tighten nuts to 24 ft lb (31 Nm).
  6. Install exhaust manifold heat shield. Tighten nuts to 35 in lb (4 Nm).
  7. Connect fuel hose to pipe.
  8. Connect 2 hoses to oil cooler.
  9. Attach water bypass hose to bypass pipe.
  10. Install starter and bolts. Tighten bolts to 34 ft lb (46 Nm).
  11. Install intake manifolds bracket and 4 bolts. Tighten bolts to 32 ft lb (45 Nm).
  12. Install grounding bracket.
  13. Connect fuel hose to fuel connector assembly.
  14. Connect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  15. Connect purge control solenoid vacuum hose to intake manifold.
  16. Attach wire harness from rear of cylinder head.
  17. Connect brake booster vacuum hose and cruise control vacuum hose to surge tank.
  18. Connect heater hose to elbow.
  19. Connect 2 fuel injection electrical connectors at rear of cylinder head.
  20. Connect 2 ignition coil electrical connectors.
  21. Install cylinder head cover.
  22. Install 7 cylinder head cover bolts. Tighten bolts to 60 in lb (7 Nm).
  23. Install vacuum pipe and 2 bolts at rear of cylinder head cover. Tighten bolts to 60 in lb (7 Nm).
  24. Connect vacuum tube to pipe.
  25. Connect loom holder to rear of cylinder head cover.
  26. Install 2 screws to high tension wire protectors.
  27. Install air hose to behind intake manifold.
  28. Install ISC air hose to idle speed actuator.
  29. Install PCV valve to cylinder head cover.
  30. Install air intake hose.
  31. Connect mass air flow sensor electrical connector.
  32. Install the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  33. Attach accelerator cable.
  34. Install 3 bolts that secure accelerator cable and air intake hose to cylinder head cover. Timing belt pulley timing marks kia-03-20-7035.gif

    NOTE: Timing belt pulley timing mark and timing mark must be aligned.
    Camshaft timing marks kia-03-20-7032.gif

    NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
  35. Install timing belt.
  36. Install timing belt cover.
  37. Pressurize fuel system.
  38. Start engine and check ignition timing.

Jul 11, 2010 | 1999 Kia Sportage

2 Answers

My 96 Jeep GC windshield washer isn't squirting. I can hear it run when pushing the washer button and I hear fluid running ; but it doesn't spray on the windshield. Also , my wiper blade in the rear window...


your rear wiper motor might be faulty,in the front i would check your fluid level-if it is full and you hear the pump running-check your washer lines to see if they are pinched-usually around where the hood closes

Feb 17, 2010 | 1996 Jeep Grand Cherokee

2 Answers

Rear windshield washer, no liquid coming out @


check that the jet is not clogged.take a very thin piece of wire,like from a twist tie and clean the hole. maybe the hose is pinched or disconnected.if you spray the rear,you should hear the pump working.i have seen hoses come off and if you spray for 20 seconds,it may leak from the car

May 15, 2009 | Chevrolet Chevy Cars & Trucks

1 Answer

Windshield washer works intermittently,one day it works nexy day it doesnt, motor good,pumps good and getting power, dealer couldnt figure it out. Rear works usually Is it the washer pump not pumping or...


If the pump is working and hoses dont have any holes or kinks the only thing it could be is a clog.. Its a common problem and easily solved. Just take hose off water resevior and blow some air through it to blow out any clogs.

Dec 02, 2008 | 2002 Mitsubishi Lancer

Not finding what you are looking for?
2011 Audi Q5 2.0 Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14204 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...