Question about 2004 Suzuki Forenza

1 Answer

My turn signals lights stop and work, stop and work

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

  • Expert
  • 245 Answers

You got a flasher problem or bulbs .

Posted on Feb 15, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Buick lucerne cxl. Third brake light works as well as front signal lights. No rear brake lights or turn signals. Tail lights and headlights and third brake lights works. Bulbs good. Help


Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Sep 08, 2017 | Buick Cars & Trucks

1 Answer

Stop lights dont work but top center does in 2003 chevy astro


Sound like a bad turn signal switch. I would bet if you wiggled the switch in just the right position the brake lights would turn on.

Jan 26, 2013 | 2003 Chevrolet Astro

1 Answer

Left turn signal stops working


Had simular problem with wife 2000 Jeep Cherookee.
My signal light were not working at all.Check flasher relay under steering colum

Nov 28, 2012 | 2000 Jeep Grand Cherokee

1 Answer

2004 Grand Prix turning Signal lights wont work.


YOU HAVE TO REPLACE THE TURN SIGNAL SWITCH.BECAUSE WHEN IT GOES OUT.SOME TIMES YOUR DIMMER SWITCH STOP WORKING.IF YOU GOING TO FIX IT YOUR SELF BESURE TO.DISARM AIR BAGS FIRST.

Aug 19, 2009 | 2004 Pontiac Grand Prix

1 Answer

Turn signal lights stop working. Neither the right or left turn signal work. Heard a noise before it stop working. The flashing started slowing down and stop blinking. Now it doesn't work at all. What


most likely its the turn signal relay. which is under the hood. in the fuse box. also make sure ur running lights are working if they are connected to the turn signal.

May 08, 2009 | 1993 Nissan Pathfinder

1 Answer

Signal lights and brake lights stopped working


the multifunction switch (turn signal switch) is a major cuase of this. your high mount stop lamp wire is run through the switch.

Dec 21, 2008 | 2000 Ford F150 Flareside SuperCab

1 Answer

Turn signal


Now replace the flasher unit! Frankster016

Oct 25, 2008 | 2002 Nissan Xterra

Not finding what you are looking for?
2004 Suzuki Forenza Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...