Question about Nissan Pickup

Open Question

Tappet settings nissan diesel sd25 - Pickup Nissan Cars & Trucks

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: tappet/valve settings???

o.25mm when hot this is for inlet and outlet

Posted on Feb 11, 2009

Ad
  • 1 Answer

SOURCE: I have a 84' nissan diesel pickup with the sd25

loosen the nuts holding the fuel lines to the injectors, roll engine over and once fuel comes out, retighten nuts until all are tight again. After that, look at the stop solnoid as it will cut the fuel flow also

Posted on May 09, 2010

SOURCE: valve tappet clearance on ld20 nissan diesel

Hi Gordon, To answer your question the actual engine type is required. Let us know what engine is fitted and we'll see what we can do. Regards John

Posted on Oct 13, 2013

  • 45582 Answers

SOURCE: How do i set the TAPPETS on a Nissan TD27 2005

tappets cannot be tight and noisy at the same time . Check the rocker and rocker shaft for wear in the shaft and rocker bushes.

Posted on Mar 21, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the tappet clearance for Nissan FD 42 engine


Valve clearances are 0.4mm for inlet and exhaust and should be checked with engine hot.

Mar 02, 2016 | Nissan Cars & Trucks

1 Answer

What is valve clearance for sd22 diesel 2.2


Intake - 0.35mm (0.014")
Exhaust - 0.35mm (0.014")

Look at the link I posted - it's the service manual. This is where I got the info from.

Hope this is helpful to you :-)
Good luck

-Scott Nissan diesel engines sd22 sd23 sd25 sd33

Feb 14, 2015 | Cars & Trucks

1 Answer

Tappet settings for Mazdz 2.5 turbo diesel 2002 model


I have a Toyota Yaris 2004 plate. The cold light stays,the fan kicks in and stays on, but the cold light does not go off. Help please. regards M Barrett

Dec 25, 2014 | Mazda Cars & Trucks

1 Answer

How do I set tappets of a 2.5 diesel turbo mazda


you haven't mentioned if it is a 4 cyl or not. However bring no 1 cylinder up to tdc and watch the tappets of the next cylinder to fire. when that cylinders rockers are in valve overlap situation ( exhaust starting to close and inlet starting to open) then that will be maximum clearance on no 1 cylinder and is when you set the tappets turning the engine until the next cylinder is at TDC watch for the next cylinder again to be in valve overlap and repeat as for no 1 cylinder

Dec 25, 2014 | Mazda Cars & Trucks

1 Answer

What is the tappet clearance for a 2.7 Diesel Nissan Hardboy 1999 model?


Try setting the valve clearance on your 1999 2.7 Nissan Hardboy diesel to 0.14 inches on the intake and exhaust sides.

Oct 07, 2014 | Cars & Trucks

1 Answer

Tappet settings for 1980 Hino am100


go on the net or contact your local service dealer, but for most diesels that do not hydraulic tappets the setting standard is .012" inlet hot and .014" exhaust hot. Make sure that the setting is required as tappet noise can be from work rocker bushes and shafts

Oct 01, 2014 | Cars & Trucks

1 Answer

Navara forum


yes this is possible to do but you need the proper computers and wireharness from the doner vehicle. it is a matter of swaping parts good luck

Dec 02, 2013 | Cars & Trucks

1 Answer

I have a 84' nissan diesel pickup with the sd25 and I can't fuel out the injectors.There is plenty of fuel in the tank, and i'm getting fuel to the injector pump.


loosen the nuts holding the fuel lines to the injectors, roll engine over and once fuel comes out, retighten nuts until all are tight again. After that, look at the stop solnoid as it will cut the fuel flow also

Apr 13, 2010 | 1984 Nissan Pickup

3 Answers

Tappet/valve settings???


o.25mm when hot this is for inlet and outlet

Jul 28, 2008 | 1988 Mitsubishi Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...