Question about 2001 Daewoo Nubira

1 Answer

Control arm replace - 2001 Daewoo Nubira

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Daewoo Master
  • 14,036 Answers

To replace control arm, you need place jackstands under the frame and lower vechicle so the weight of the vechicle rests on the jackstands and not on the control arms, then remove the front wheel remove ball joint and nut, remove steering knuckle from the lower ball joint using tool KM 507 B. remove control arm to crossmember nut and bolt, remove rear crossmember to body bolt and remove control arm.torque control arm to crossmember nut and bolt 81 ft lbs, torque ball joint to steering knuckle bolt nut 44 ft lbs.torque crossmember to body bolt to 145 ft lbs.

Posted on Feb 15, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a lower control arm assembly on 04trailblazert


How to Replace an Upper Control Arm - YouTube

? 15:18
https://www.youtube.com/watch?v=wZGr8Xf2ip8
Oct 10, 2014 - Uploaded by ChrisFix
Learn how to replace the Upper Control Arm on a Chevy Trailblazer, GMC ... can you do a video on how to ...

Installing Rubber bushing on lower arm for trailblazer ...

? 0:53
https://www.youtube.com/watch?v=KYIPc_ZXMJo
Jul 27, 2013 - Uploaded by Abdul Hameed
Installing Rubber bushing on lower arm for trailblazer ... How ToChange Control Arm Bushings Using A ...

Nov 28, 2015 | Cars & Trucks

2 Answers

How would I replace just the lower ball joint on a 2002 Chevy Malibu


I list a lower ball joint available to purchase.
So you would have to disconnect the lower control arm from the spindle to replace the joint.

Oct 13, 2015 | Cars & Trucks

1 Answer

Left front lower control arm broken in 2004 Honda Civic Hybrid


i would replace it, not easily done you need special tools

Feb 13, 2014 | 1993 Chevrolet C1500

1 Answer

How to remove ball joint from lower control arm where it is connected


In the Endeavor you need to replace all the lower control arm; the ball joint is fitted like one piece in the control arm and you can't change it alone, you need to replace all the control arm. Maybe some people can force it but I don't recommend that, the part are not design to be replaceable, it's too risky. Put a new OEM control arm.

Nov 04, 2013 | 2004 Mitsubishi Endeavor

1 Answer

Want to know the relationship between the rear trailing arm and the control arm. If you had the rear trailing arm fixed because of recall then 2 months later they say the control arm came loose and broke...


The recall for your vehicle may or may not have included replacement of the trailing arm. The recall says that the trailing arm is to be "inspected" then it will be replaced, or modified at the discresion of the person performing the inspection. If it was "replaced", it would require the control arms to be disconnected and reconnected. If it was only "modified" there would have been no disassembly of the control arms required. See the picture below. The picture shows the rear suspension parts. Notice that the upper control arm and the lower control arm bolt to the trailing arm. (which is what also houses the hub and bearing with the wheel speed sensor.) I hope this helps you to resolve your issue.

dttech_35.gif

Mar 08, 2011 | 2003 Hyundai Santa Fe

1 Answer

How to replace s500 control arms How much do they cost, and it there an additional ball joint. My mechanic tacked this on. I thing the control arm and ball joing is one unit.


To replace the lower control are you need to unbolt it from the subframe, airmatic strut, sway bar link and from the lower ball joint. The lower ball joint is separate from the lower control arm. The ball joint actually gets pressed into the steering knuckle. Then the lower control arm sits on top of the ball joint and gets bolted down. The lower control arms list price are about $330 each and the ball joints are around $78 each for oem mercedes parts. The total labor for both to be replaced is somewhere between 6-8 flag hours. The thrust arms are also part of the front suspension and those arms are one piece that have a ball joint as part of the arm. The lower control arm usually doesn't need to be replaced unless its damaged since the control arm bushings are available separately and are around $73 each side for the kit.

Oct 07, 2010 | 2003 Mercedes-Benz S-Class

1 Answer

How to chnge control arm bushing on 1994 dodge intrepid


Here are the instruction on how to replace your control arm bushing. please not that there is a special tool needed that you will need to get from you auto parts retailer. you can usually rent these tools.
    1. Turn the control arm over in the arbor press, then position the arm so that it is supported by the receiver tool MB-990799 as shown.
  1. Position the new bushing into the control arm so it is square with the bushing hole. Position the installer tool MB-6644-1 or equivalent on top of the bushing, with the bushing setting in the recessed area of the installer tool. Press the bushing into the control arm.
  2. Press the control arm bushing into the control arm until the installer tool squarely bottoms against the surface of the control arm. When the installer tool squarely bottoms on the control arm, the bushing is installed in the arm in the correct position.
  3. Install the tension strut into the strut bushing in the control arm. Position the tension strut in the control arm with the word FRONT stamped in the tension strut positioned away from the control arm. With an open end wrench on the flat of the tension strut to stop the tension strut from turning. Tighten the NEW tension strut-to-control arm retaining nut to 110 ft. lbs. (150 Nm).
  4. Install the lower control arm and tension strut back onto the vehicle. Refer to the Lower Control Arm procedure earlier in this section.


Control Arm-to-Tension Strut Bushing
To replace the control arm tension strut bushing, the control arm and tension strut assembly must be removed. The removal of the bushing requires the use of an arbor press.
  1. Thoroughly lubricate the replacement tension strut bushing, control arm and installer tool 6644-3 or equivalent with a silicone lubricant.
  2. By hand, install the tension strut bushing into the large end of the installer tool. Press the bushing into the installer tool as far as it will go by hand.
  3. Position the control arm in the arbor press so that the tension strut hole in the control arm is centered on the receiver tool MB-990799 or equivalent. Position the installer tool with the previously installed bushing, inside of the tension strut bushing hole in the control arm. Position the installer tool on top of the tension strut bushing. Using the arbor press, press the tension strut bushing into the control arm. As the bushing is being pressed into the arm, a pop will be heard. When the pop is heard, the installer tool will slightly move up off the control arm. At this time remove the control arm assembly from the press and pull the tool MB-6644-3 off of the tension strut bushing in the control arm.


Jun 19, 2010 | 1994 Dodge Intrepid

1 Answer

Can you replace the lower ball joints in the control arms


You can replace them seperately,but they need pressed out and in. Other methods of removing and installing likely will damage control arm.

Apr 23, 2009 | 1998 Ford Expedition

1 Answer

How to change upper control arm on 1996 Honda Civic DX ?


UPPER CONTROL ARM:

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.
  1. Raise and support the vehicle safely.
  2. Remove the front wheels. Support the lower control arm assembly with a floor jack.
  3. Separate the upper ball joint from the steering knuckle using a ball joint separator tool.
  4. Remove the self-locking nuts from the upper arm anchor bolts. Remove the upper arm from the vehicle.

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.
To install:
Use new self-locking nuts when installing the upper arm and strut.
  1. Install the upper control arm assembly into the strut tower.
  2. Connect the upper ball joint.
  3. Install the front wheels and lower the vehicle.
  4. With all four of the vehicle's wheels on the ground, torque the upper control arm nuts to 47 ft. lbs. (65 Nm). Torque the castle nut to 32 ft. lbs. (44 Nm); then, only tighten it enough to install a new cotter pin.
  5. Tighten the wheel nuts to 80 ft. lbs. (110 Nm).
  6. Check and adjust the vehicle's front end alignment.
The bushings on the front lower control arms are replaceable on most models.
This procedure requires the use of a press and may be above the skill range of the average driveway enthusiast. It is recommended that this procedure be done by a qualified machine shop if you are not skilled in the proper use of a press.
  1. Remove the lower control arm that is in need of new bushings.
It is recommended that both the left and right lower control arm bushings be replaced at the same time. The vehicles handling may become unstable if there are new bushings on one side of the car and worn ones on the other.
  1. Set up the control arm in a press.
  2. Using a impact socket of the correct length and size, press out the old bushing.
  3. Install the new bushing by slowly using the press to push it into the control arm.
  4. WARNINGExcessive force could cause the bushing to bend or tear so be careful.
  5. Once the bushing is properly seated in the control arm, remove the arm from the press and install it on the vehicle.

Apr 05, 2009 | 1996 Honda Civic

3 Answers

2004 Nissan Quest front control arm bushing replacement.


Sorry guys not a solution but I too have an 04 Quest, which supposedly has worn controller arm bushings and Nissan says I need both controller arms replaced. For a total of $950!!! I was told that they need to replace the whole arm and cannot replace only the bushings. Now reading the posts on this site I find that to be untrue. Seems all I need to spend is anywhere from $25 to $35 per bushing.

Nov 30, 2008 | 2004 Nissan Quest

Not finding what you are looking for?
2001 Daewoo Nubira Logo

399 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...