Question about 2008 GMC Acadia

Open Question

Blend door How to change blend door actuator

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jturcotte
  • 8516 Answers

SOURCE: How do I test to see if my actuator for my blend

Hi, you would need a test light or voltmeter to check the cable. Back-probe (stick your probes in the back of the connector) the terminals 5 and 6 (brown and white wires) with your test light/voltmeter. Turn the key on and change the temperature setting. A voltage should show. See diagram below and let me know if you have any questions.

jturcotte_781.gif

Posted on Jan 09, 2011

Ad
  • 436 Answers

SOURCE: How do you fix the driver side air blend door actuator?

you cannot repair the actuator you need to replace it with new one. These motors turn but get weak with time. if you test it, it works, put it in and it doesn't. this is because the motor is weak, unfortunately GM does not sell these motors separately.

Posted on Aug 23, 2009

  • 2 Answers

SOURCE: How do you change a blend door actuator on a 2003

Not sure why previous poster showed you how to fix a switch in the door, but anyways.....
I had same problem as you.

My Yukon has the single overhead door, not the "barn-doors", hopefully yours is the same. Open rear cargo door. Using a trim tool (buy the set from Harbor Frieght for less than $10) remove the lower trim (at carpet), upper trim (at headliner), then the right pillar trim (mine has small Bose speaker in it). Loosen trim between passenger side back door and the cargo area main right rear trim. Remove main cargo area right main panel, by unscrewing the big black know, prying out the small plastic plug, and carefully disconnecting the AUX power plug (looks like a cig lighter outlet) once you can get behind the panel a little bit.

Now you are looking at the entire rear system. There are 2 of these actuators. The front one controls airflow going either to floor or ceiling vents, the rear one (towards middle of entire unit) controls AC vs heat percentage flowing through the ducts. Unplug the connector, and 3 screws to remove it.

Install is the reverse.

Posted on Mar 14, 2010

Mr BrokRench
  • 1623 Answers

SOURCE: i beleave my blend door

Under the dash on the passenger side.

Posted on Jul 24, 2011

  • 1311 Answers

SOURCE: 2003 gmc envoy XL where is the blend doors

Here is a diagram of the front HVAC system.

freddyboy61_15.jpg

Posted on Aug 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is rhe air temp. Door actuator in a 2003 ford 450 truck


Ford Superduty Erratic Temp Blend Door Actuator Removal - YouTube

? 12:29
https://www.youtube.com/watch?v=dYPOtin3JUk
Dec 1, 2013 - Uploaded by FordTechMakuloco
Only buy the Ford Actuators, you can get them cheaper here- ...

Simple how to fix blend door heater a/c actuator 2002 - 2008 ford ...

? 7:12
https://www.youtube.com/watch?v=EEWuJuhCtmc Aug 24, 2013 - Uploaded by kirk colombo
Simple how to fix blend door heater a/c actuator 2002 - 2008 ford explorer noise .... I literary just finish ...

08-10 Super Duty Blend Door Actuator Location - Dual System ...

? 1:24
https://www.youtube.com/watch?v=s7awF2fTKf4 Mar 22, 2012 - Uploaded by srmastertech
Here is a quick view showing the location of the temp blend door actuators on the Ford Super Duty's with ...

Ford blend door fix - 15 minutes - YouTube

? 3:22
https://www.youtube.com/watch?v=wsjGxreGlkA Jul 21, 2013 - Uploaded by SoonersWarriors
Ford blend door fix - 15 minutes. SoonersWarriors. Loading ... Ford Vehicles: Frequent Blend Door Actuator ...

Blend Door Actuator Ford Super Duty 08-10 - YouTube

? 9:45
https://www.youtube.com/watch?v=mbzjCPYENZQ Oct 4, 2013 - Uploaded by MostExcellentDude
This applies to 2008-2010 F250 and F350 with the dual climate control. This video shows the locations for the ...
blend door actuator 2003 ford f450 Google Search




Aug 16, 2017 | Ford Cars & Trucks

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

2 Answers

Air blend actuator 2000 ford explorer is not working?


First, insure you do not have a vacuum leak or bad vacuum check valve. If this is all good, you may have to change actuator and every model has a different way to access this--some require dash removal. If you must do this, get a shop manual as the air bags CAN BE VERY DANGEROUS!

Mar 28, 2016 | 2000 Ford Explorer Eddie Bauer

1 Answer

How to replace temp blenddoor actuator


images for bonneville How to replace temp blend door

GM Blend Door Actuator Repair (Saturn, Chevy, GMC, Buick ...

? 4:28
https://www.youtube.com/watch?v=fER3ZqnYLZg
Jul 11, 2014 - Uploaded by willmacneill
I sell the gears needed to fix your blend door actuator! ... Theactuator is used to change the temperature, position(floor, vents,defrost) or ...

Dec 03, 2015 | Pontiac Bonneville Cars & Trucks

2 Answers

Where is the driver side blend door actuator on a 98 Seville STS?


I believe that the right side has a blend door actuator, and the left side or driver side just gets air from the regular flow from the programmer and vacuum motors.

Dorman/Blend Door Actuator
Part Number:
604-106
btn-view-details.png Price: $139.99
Notes: Dorman-OE SolutionsTemperature door. Right

Oct 29, 2010 | 1998 Cadillac Seville

2 Answers

2004 f350 ford heater blows cool air but hoses are both warm-where do i start looking


check to see if the blend door is moving where you change the temperature setting. I think your blend door is behind the glove box. Here are instructions for removing the actuator. Take it off, plug it back in and see if the motor rotates. Also check to see if you can rotate the blend door by hand. If you can rotate it by hand, the motor is probably broken of the gears are stripped. Let me know if you have questions.
  1. Release the stops and lower the glove compartment door.
  2. Disconnect the connector.
f4b0b74.gif Fig. Blend door actuator-F-250 & 350


  1. Remove the two screws. Rotate the blend door actuator and bracket assembly. Remove the electronic blend door actuator and bracket assembly.
  2. To install, reverse the removal procedure.

Oct 17, 2010 | 2004 Ford F350

2 Answers

200 Jeep Laredo..Air is cold and fan is blowing,


there is a blend door actuator for the laredo and if is bad the air wont come out here is a pic of what it looks like and how to get to it


The single zone heater-A/C system is equipped with a single blend door actuator. The dual zone system has two blend door actuators, one for the driver side blend-air door and one for the passenger side blend-air door.
7d2da02.gif
  1. Disconnect and isolate the negative battery cable.
  2. Remove the glove box from the instrument panel.
  3. Remove the three screws that secure the blend door actuator to the passenger side of the HVAC air distribution housing .
  4. Remove the blend door actuator from the air distribution housing and disconnect the HVAC wire harness connector from the actuator.
  5. Remove the blend door actuator from the vehicle
to instal
  1. Position the blend door actuator into the vehicle.
  2. Install the blend door actuator onto the passenger side of the HVAC air distribution housing . If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the blend door cam .
  3. Install the screws that secure the blend door actuator to the passenger side of the air distribution housing . Tighten the screws to 17 inch lbs. (2 Nm).
  4. Connect the HVAC wire harness connector to the blend door actuator.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable.

Sep 09, 2009 | 1998 Cadillac Seville

3 Answers

01 silverado blend door changed /now works back wards!!!


most likely needs a LH (bottom) temp actuator. Located in the center of the dash on the bottom, you have to remove the hush panel on the rh side of the truck

Apr 24, 2009 | 2001 Chevrolet Silverado

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...