Question about Cars & Trucks

1 Answer

I need the required valve & inyector clearance on a M11 engine

Posted by on

  • yadayada
    yadayada Feb 15, 2012

    What is an "M11" engine, have no idea what so ever. 

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,212 Answers

Cummins M11

Intake valve clearance 0.010 inch
Exhaust valve clearance 0.024 inch

The firing order is 1-5-3-6-2-4 and that is the order the valves should be adjusted started with first timing mark on main pulley adjust cylinder number 1 The valves and injector should be adjusted at the same time The crankshaft is then rotated 120 degrees to next timing mark and cylinder 5 is adjusted, the crank is rotated again 120 degrees to next timing mark and cylinder 3 is adjusted.then back to the first timing mark, cylinder 6 is adjusted, etc/

Adjusting nut on plunger should be adjusted to the point where you feel the plunger just reaches the bottom.of travel/bottoms out.

Posted on Feb 15, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fischmilch
  • 96 Answers

SOURCE: i need to know the vavle clearance of nissan z20 engine.

VALVE CLEARANCE ADJUSTMENT
Application In. (mm)
Intake .010-.013 (.26-.34)
Exhaust .011-.015 (.29-.37)

Posted on Mar 20, 2009

  • 34 Answers

SOURCE: Cyl. head tightening torque and sequence for a

The online manuals are a super help. I use them all the time. http://www.autozone.com/autozone/myzone/profile/membershipBenefits.jsp

Posted on Oct 14, 2009

SOURCE: I am rebuilding 3cyl diesel

you will need a manual for this as diesel torque settings are different to that of a petrol engine.

Posted on Jul 18, 2008

  • 653 Answers

SOURCE: Engine tappet clearances

According to http://freespace.virgin.net/tommy.sandham/databook.htm# Rocker Adjustment, the cold clearance is .008" intake/.018" exhaust in the non-GT 1500cc, and .012" intake/.022 exhaust on the GT. Sweet little car!!!

Posted on Mar 01, 2009

moparownr
  • 667 Answers

SOURCE: 96 escort valve clearance

Gary, the 1.9L Ford engine has hydraulic lifters no valve adjustment is needed

Posted on May 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the valve lash specs for 2007 Honda Accord V6?


There is a specific procedure for setting valve clearance . I highly recommend getting a repair manual for the correct specs & procedure. The engine must be at TDC with the #1 cylinder on the compression stroke , that will allow you to adjust ONLY certain valves , then you have to turn the engine one turn to TDC again only now #1 will be on the exhaust stroke & the rest of the valves can be adjusted . it's important that you know the difference between the two !

Jan 08, 2015 | Honda Cars & Trucks

3 Answers

2005 terracan recently started engine check light coming on ONLY towing boat.error codes p1119 and p1120.Anyone any idea why because Hyundai dont


HOW ARE THE BRAKES WORKING FOR YOU THIS MAY BE A ANTI-LOCK BRAKE PROBLEM HOW HEAVY WAS THE BOAT YOU WERE TOWING, & DID YOU HAVE ANY PROBLEMS STOPPING WHILE YOU WERE TOWING THE BOAT?

Dec 28, 2012 | 2005 Hyundai Terracan 2.9

1 Answer

WHAT IS A VALVE CLEARANCE OF CUMMINS ENGINE MODEL M11


.014" on the intake and .027" on the exhaust

Sep 12, 2012 | Cars & Trucks

2 Answers

Tikking noise coming from engine


Yes, you're right, those could be the cause. Also, possible it's a collapsed hydraulic valve lifter, if your car has hydraulic operated (from engine oil) valve lifters. At any rate, it sounds like something loose in the valve train-valve lifter with push rod engines; or cam followers {rocker arms) with overhead cam engines that push on the top of valve stems .
Check a repair manual to see if your engine has valves that can be and need adjusting. Engines with valve lifters do not require periodic adjustment for proper valve clearance. Engines with rocker arms do require checking the valve clearance every couple of years or so.

Apr 07, 2012 | Cars & Trucks

1 Answer

I need to know how to go about the second procedure for valve clearance on my 1.5l mitsubishi lancer. ive started on TDC AND COMPLETED THE FIRST STEP BUT LEADING ON TO THE SECOND STEP IS TROUBLE?????? HELP


the easiest way is to start at the first valve,first you need to know if the inlet & exhaust valves have the same clearance, starting from the left side of the engine ( standing at the front ) the first valve exhaust, the next two are inlet, the next two are exhaust, the next two are inlet & the last one is exhaust, what you do is turn the engine over by hand ( this might be easier if you remove the spark plugs ) until the valve opens & closes, after it closes turn the engine a little more & adjust the clearance on that valve, repeat this action on every valve until they have all been adjusted.......hope this helps......cheers.

Sep 03, 2011 | Mitsubishi Lancer Cars & Trucks

2 Answers

I have problem with my engine 4K toyota. It heard an engine noise during idling, for my little knowledge in engine repair, can you give me any procedure mannuals in adjusting engine valves for my...


Valve Clearance Valve clearance is there to allow the valves to cool in between combustion events (spark), and to make sure the valve closes properly and contains the combustion explosion. You need to cool the valves a little bit, the exhaust valve moreso than the inlet, as it's what sees the most heat as spent burnt gases go past it into the exhaust port. Run too little clearance and you'll cause the valve to "weld" a little bit to its' seat every time it closes, and then take seat metal off again when it opens. Do this enough times and you burn out the valve seat and need the head reconditioned. However, by running less clearance, the valve stays open for that little but longer, and you get more air in and out of the motor, and make more power. Run too much clearance and your motor just sounds like a diesel and loses power and tappet rattle annoys you while you're driving, so it's better to err on the side of caution.
The stock valve clearance (0.008" inlet / 0.012" exhaust, warm) is pretty good for any of the cams I've listed above, they're well-sized street cams, not really wild top heavy race cams that require super high compression to work, so don't be afraid to close the valves up a bit from the suggestions of the cam grinder, which will usually say between 0.010" and 0.014". There are a few ways to set your valve clearances:
Yellow Book Method This is from the factory 3K/4K/5K engine manual, aka The Yellow Books. It's the quick and lazy method.
Set engine to #1 TDC. Crank pulley timing mark should be on 0, distributor rotor should be pointing towards spark plug 1 or 2. Set tappets (counting from the front) 1, 2, 3 and 5. Rotate engine 360 degrees, crank pulley to 0 again, distributor rotor turned 180 degrees. Set tappets 4, 6, 7 and 8.
Nine Method I've never really gotten into doing this, takes too much time and maths for my liking :P Rotate the engine through its' range of movement, as one valve is "on the rock" of its' max lift, subtract the valve number from 9 and that's the tappet you should be setting. For example, if #8 valve is open, set clearance on valve #1. If valve #7 is open, set clearance on #2. And so on.
Stewart uses this method, and rotates the camshaft through its entire base circle and sets the clearance at the highest point. Which is a pretty good idea, as it compensates for the possibility that the base circle has been ground unevenly, and allows you to run the proper valve clearance that you want to run, instead of something that may be a few thou larger in reality.

Feb 10, 2011 | Toyota Corolla Cars & Trucks

2 Answers

How do you change the oil pump in a 1995 Lumina van with a 3.8?


REMOVAL

  1. Remove front cover.
  2. Remove oil filter adapter, pressure regulator valve and spring.
Fig. 16 Oil Pump & Housing 42162079

  1. Remove oil pump cover attaching screws, then the cover and gears, Fig. 16 .
INSPECTION

  1. Check pump cover and housing for cracks, scoring, porous or damaged casting, damaged threads or excessive wear or galling. Replace as required.
  2. Check pressure regulator valve for scoring, burrs or sticking in valve bore. Replace as required.
  3. Check pressure regulator valve spring for tension loss or bending, replace spring as required.
  4. Check gears for chipping galling or excessive wear, replace as required.
Fig. 17 Oil Pump Inner Gear Tip Clearance Inspection 42162080

  1. Measure oil pump inner gear tip clearance, Fig. 17 . Maximum clearance should be 0.006 inch.
Fig. 18 Oil Pump Outer Gear Diameter Clearance Inspection 42162081

  1. Measure oil pump outer gear diameter clearance, Fig. 18 . Clearance should be 0.008-0.015 inch.
Fig. 19 Oil Pump Gear End Clearance Inspection 42162082

  1. Measure oil pump gear end clearance with gear dropped in housing, FIG 19. Clearance should be 0.0010-0.0035 inch.
  2. Measure pressure regulator valve for valve to bore clearance of 0.0015-0.003 inch.
INSTALLATION

  1. Lubricate all gears with clean motor oil, then install gears in housing.
  2. Pack pump cavity with suitable petroleum jelly.
  3. Install pump cover and cover attaching screws. Tighten cover attaching screws to specifications.
  4. Install pressure regulator valve and spring.
  5. Install oil filter adapter using a new gasket, tighten oil filter adapter attaching bolts to specifications.
  6. Install front cover on engine. During front cover installation, ensure inner pump gear is properly engaged on crankshaft sprocket.

Jan 29, 2011 | Chevrolet Lumina APV Cars & Trucks

1 Answer

I need the required valve clearance for a 98 1/2 dodge 5.9 24 valve cummins diesel engine


there should be a tag on your engine with recomended valve clearances.

Dec 21, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

My lifters are getting really loud on my 91 honda accord ex


All you need is to adjust the valve tappet clearance back to the original specification. It is a time consuming effort and require passion to do it. You need to remove the top engine cover, set timing belt to top dead centre then adjust intake & exhaust valve clearance one by one. Rotare the cranckshaft 180 degree and repeat the valve clearance,. I would suggest to leave it to the expert.

Jul 15, 2009 | 1991 Honda Accord

1 Answer

Need to know how to adjust valves, or a print-out of adjustment procedure and tools reguired. 1989 toyota gt-s corolla 1600 16 valve 4a-ge cal engine


This engine utilizes shims to set proper clearances, you will need a micrometer, valve clearance adjustment tool set for shimmed lifters,small magnetic arm, appropriate shim selecting charts (manufacturer will have this if you can get the nec. measurements).
Measure thickness of shims removed (using micrometer) and use this formula where T=Thickness of old shim; A=Valve clearance measured; N=Thickness of new shim required.
Intake valves:   N = T + (A - 0.02 mm (0.008 in.)) Exh. valves:     N = T + (A - 0.25 mm (0.010 in.))
Then you need to find shims as close as possible to the calculated values.
Valve clearances (cold) are as follows: Intake 0.15 - 0.25 mm (0.006 - 0.010 in.) Exhaust 0.20 - 0.30 mm (0.008 - 0.012 in.)
Note, if you are not familiar with precision measuring using a micrometer, this may be better left to a trained tech. These are high revving little power plants and you don't want a problem at 8K rpm.

Jun 05, 2009 | 1989 Toyota Corolla 2 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,330 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...