Question about Cars & Trucks

2 Answers

I'm looking for a diagram of the timing chain and timing marks for mondeo st 220?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 17,970 Answers

Duratec ST-220 used in the top of the line Mondeo 3.0 liter V6.

The original Duratec V6 was introduced in Europe in 1993 in the Ford Mondeo (Ford Contour/ Mercury Mystique in NA). Then in 2000 the smaller 4 cyl Mondeo engines also got the Duratec name, as well as others. Check this for 3.0L 6cyl...


i'm looking for a diagram of the timing chain  - 2_15_2012_8_32_29_pm.jpg

Fig. Be sure the timing marks are as shown after the chain has been installed-2001-04 3.0L (VIN S) engine ( zoom link here )

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Feb 15, 2012

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 22,219 Answers

Is this a ford mondeo with a zetec engine ,or do you mean the ford engine as used in the scorpio with timing chain ,both these engines are times up with a flat slot on the back of the cam shaft ,its the scorpio engine that bothering me as i done a couple but it was a few years ago ,iam sure it had flats on the back of the camshaft but i remember a engine with two lugs on the camshafts as well and they had to align up ,if in doubt look at the way the cam lobes point on no1 cylinder and then look for a mark of some description,inlet pointing up at angle to the left and the exhaust up and to the right with piston at no1 but when moving the cams make sure all the four pistons are downa bit so they dont crunch

Posted on Feb 15, 2012

  • Colin Stickland
    Colin Stickland Feb 15, 2012

    thanks for the info but never seen this V6 engine ,the 2.2 is i think the 4 cylinder one witha timing chain but i have only seen it in the scorpio which was before the mondeo but its possible this was used when they run out of engines on the assembly line knowing ford .Most mondeos i see are diesel and are run for ever chug along buses .

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 512 Answers

SOURCE: 3.3l dodge caravan, where to set timing chain marks

the top gear timing mark points at 6oclock...crank gear at 12 oclock

Posted on Sep 27, 2008

  • 12 Answers

SOURCE: timing chain mark diagram for a 94 grand am????

would your engine be a 2.4 quad ??

Posted on Apr 15, 2009

  • 6982 Answers

SOURCE: timing chain mark diagram for a 94 grand am????

Haynes lists the entire procedure for setting the position of the cams etc. Positioning of these is critical...If off by even a slight amount the valves WILL strike the pistons and destroy the engine. DO NOT use any parts made by SA Gear...They have no quality control and will deny any claim made against them. Make sure that the chain guides are in good condition and that the chain tensioner is operating properly.

Posted on Apr 15, 2009

kennyz195
  • 61 Answers

SOURCE: 1999 Ford Expedition 5.4L Timing chain setup

.

  1. Remove the engine front cover. For additional information, refer to Engine Front Cover in this section.
  1. Remove the crankshaft sensor ring from the crankshaft.
    a0044041.gif
  1. Rotate the crankshaft until the timing mark on the RH camshaft sprocket is approximately at the 11 o'clock position and the timing mark on the LH camshaft sprocket is approximately at the 12 o'clock position.
    a0049532.gif
  1. Using the special tool, position the crankshaft as shown.
    a0041102.gif
  1. Install the special tool.
    aa5423a.gif
  1. NOTE: LH shown; RH similar.
    Remove the two bolts, the timing chain tensioner and tensioner arm.
    aa5952a.gif
  1. Remove the LH and RH timing chains and the crankshaft sprockets.
    • Remove the special tool from the crankshaft.
    • Remove the timing chains from the camshaft sprockets.
    • Remove the right and left timing chains and the crankshaft sprocket from the crankshaft.
    a0029151.gif
  1. ani_caut.gif CAUTION: The bolts are different lengths and must be returned to their original location.
    NOTE: LH shown; RH similar.
    Remove the bolts and the timing chain guides.
    a0044040.gif
Installation
  1. ani_caut.gif CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result.
    ani_caut.gif CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
    Compress the tensioner plunger, using an edge of a vise.
    da0605a.gif
  1. Using a small screwdriver or pick, push back and hold the ratchet mechanism.
    da0606a.gif
  1. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing.
    da0607a.gif
  1. Install a paper clip into the hole in the tensioner housing to hold the ratchet assembly and plunger in during installation.
    a26917a.gif
  1. Remove the tensioner from the vise.
  1. NOTE: There are 61 links in the timing chain.
    If the copper links are not visible, mark two links on one end and one link on the other end, and use as timing marks.
    a0038720.gif
  1. Install the timing chain guides.
    a0044063.gif
  1. Using the special tool, verify correct crankshaft position.
    • Remove the special tool.
    a0041102.gif
  1. NOTE: Crankshaft sprockets are identical. They can only be installed one way. Refer to the following illustration for correct crankshaft sprocket installation.
    If removed, install LH and RH crankshaft sprockets.
    a14824b.gif
  1. Install the LH timing chain onto the crankshaft sprocket, aligning the one copper (marked) link on the timing chain with the slot on the crankshaft sprocket.
    a0041197.gif
  1. Position the LH timing chain on the camshaft sprocket with the two copper (marked) chain links and the camshaft sprocket timing mark aligned.
    a0049191.gif
  1. Position the RH (outer) timing chain on the crankshaft sprocket, aligning the copper (marked) link with the timing mark on the sprocket.
    a0041196.gif
  1. Position the RH timing chain on the camshaft sprocket. Make sure the two copper (marked) links align with the camshaft sprocket timing mark.
    a0041104.gif
  1. NOTE: LH shown; RH similar.
    Position the tensioner arms and tensioners, and install the bolts.
    aa5952a.gif
  1. Remove the tensioner retaining clip.
    a26273a.gif
  1. As a post-check, verify correct alignment of all timing marks.
    a0041106.gif
  1. Remove the special tool.
    aa5423a.gif
  1. Position the crankshaft sensor ring on the crankshaft.
    a0044041.gif
  1. Install the engine front cover. For additional information, refer to Engine Front Cover in this section.


2010&c18=modelyear&c20=n310677&c35=wsm%2ctiming%20drive%20components%2csxj%2c303-01b%2cin-vehicle%20repair&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Posted on Apr 07, 2010

  • 564 Answers

SOURCE: replacing a timing chain on a 96 grand am. need a

it is a good idea to get a haynes repair book on your type of car it will give u step by step how to do it,,it is not much,,,

Posted on Apr 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i replaced timing chain, mondeo tdci, I turned engine buy hand to make sure all is tight but timing marks are 1 tooth out now?


distributor ? advance/retard may get you close enough, if you can\'t cheat like this, do chain over

Oct 04, 2014 | Cars & Trucks

2 Answers

Need picture of timming marks


has the timing chain been replaced

Mar 27, 2014 | 1984 Datsun 2.8

1 Answer

Correct way to install timing chain on suzuki grand vitara h25a &diagram


alldata dot com has a that , as does mitchels and chilton online.
http://www.fixkick.com/look/v6/6v-chain-marks.jpg

Mar 10, 2013 | 1999 Suzuki Grand Vitara

2 Answers

Noise in the timing chain


May be its problem with timing chain and it has to be inspected and replaced.Or its possible that timing chain is got misaligned.

There are few help,links provided related to timing chain assembly and dis-assembly. Go through it and confirm proper inspecting of timing chain.

Click the required help link below:----How to Replace Timing Chain Cover & Seal on Audi A4 ? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-timing-chain-cover-seal.html
----------1982 Toyota Pickup: Set ignition timing, engine overheating, timing chain issue, dist off? http://whatisbyme.blogspot.in/2012/05/1982-toyota-pickup-set-ignition.html
----------How to Remove Timing Chain Cover and Seal on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-timing-chain-cover-and.html

--------


How to Remove Timing Chain and Gears on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-timing-chain-and-gears-on.html

-------


Ford Mondeo ST220 camshaft Timing specifications? http://technoanswers.blogspot.in/2012/02/ford-mondeo-st220-camshaft-timing.html
------------Replacing Timing Chain Cover For 2009 Ford?

http://repairhelpcenter.blogspot.in/2012/03/replacing-timing-chain-cover-ford-2009.html


-----------
Timing Chains & Front Cover Removal on 2008 Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/timing-chains-front-cover-removal-on.html
----------How to Replace Timing Chain Cover, Chain, Sprockets, & Seal On Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-cover-chain.html
---------How to Replace Timing Chain & Sprockets on Ford Windstar? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets.html
---------Timing Chain & Sprockets Replacing on Ford, Mercury and Lincoln? http://fordrepairhelp.blogspot.in/2012/03/timing-chain-sprockets-replacing-on.html
----------How to Replace Timing Chain & Sprockets on Ford Edge and Lincoln MKX? http://howtobyme.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets.html
------How To Replace Timing Chain, Sprockets & Front Cover on Ford Expedition and Lincoln Navigator? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets_356.html
---------Timing Chain, Sprockets, Front Cover & Seal removal for Ford Mustang? http://schematicsdiagram.blogspot.in/2012/03/timing-chain-sprockets-front-cover-seal.html
---------How to Replace Timing Chain on Buick LaCrosse? http://howtobyme.blogspot.in/2012/03/how-to-replace-timing-chain-on-buick.html
---------These details will help.For more help keep updated.Thanks.

Oct 15, 2012 | Cars & Trucks

1 Answer

Set timing chain


There are marks on the cam sprockets & colored
links on the chains & mark on the crank gear

You need to get a diagram to follow
Try a local repair shop, they can print one for you,
as long as they have a data base, no data
base they won't be around long, so try the next shop

If you work the internet you will come up with it, I
would think,we have nothing, we're like you at home
just use the site as you do

Oct 02, 2012 | 1998 Ford Explorer

1 Answer

Need diagram for timing chain on 1987 dodge dakota 3.9l v6


The crank & cam gears have marks on them,
shouldn't need a diagram

Turn it over & align the gears & familiarize yourself
with what your taking apart

Sep 29, 2012 | 1987 Dodge Dakota

1 Answer

I have a 2002 nissan altima 2.5 and i just put in a rebuilt head in it like a week ago, but now the rpm's are low and when the car is in iddle it shakes a little. When i run the car it feal like a


It is definatly a timeing problem but 1st check you pluged all wireing back in especially cam sensor & VVT solinoid if fitted. You may just need to reset the code & see if prob remains. I had a honda engine light come on after haveing VVT solinoid out & just had to reset comp & it was fine. If all looks good there you will need to recheck the cam timeing you could be a tooth out. Look at this link. http://www.permoveo.ltd.uk/tabid/122/OBD-Error-Code/P0011/Diagnostics/Nissan/Default.aspx

Jul 08, 2012 | Cars & Trucks

1 Answer

Needing a timingbelt diagram 1997 Altima Nissan GXE L4-2.4L


  • It's a timing chain not a belt.

  • This diagram shows how to position the lower timing chain so that the mating marks line up.


11_25_2011_1_46_21_am.jpg

  • Lower timing chain tensioner and timing chain guide positioning.

11_25_2011_1_48_38_am.jpg
Double check the mating mark alignment of the upper timing chain and idler sprocket.

11_25_2011_1_50_07_am.jpg
  • Make sure that the upper timing chain and camshaft sprocket mating marks align.


11_25_2011_1_51_12_am.jpg

  • There are the diagrams you requested.
  • Hope this helps...



Nov 25, 2011 | Cars & Trucks

1 Answer

1997 Nissan-Datsun Altima GXE L4-2.4L timingbelt diagram


  • It's a timing chain not a belt.

  • This diagram shows how to position the lower timing chain so that the mating marks line up.


11_25_2011_1_46_21_am.jpg

  • Lower timing chain tensioner and timing chain guide positioning.

11_25_2011_1_48_38_am.jpg
Double check the mating mark alignment of the upper timing chain and idler sprocket.

11_25_2011_1_50_07_am.jpg
  • Make sure that the upper timing chain and camshaft sprocket mating marks align.


11_25_2011_1_51_12_am.jpg

  • There are the diagrams you requested.
  • Hope this help.

Nov 25, 2011 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,503 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...