Question about 2005 Mazda 3

Open Question

Timing marks after belt chang mazda 121

Are there timing on the pullys as inmark for top dead center

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 37 Answers

SOURCE: 1991 mazda b2200- timing belt changed

The keyway and or the dot on the crank should be line at 12 oclock. You will see a point on the oil pump housing to go by. On the camshaft the pointer will be at 12 oclock also. Use the O on the camshaft to the top at mark. Be sure to look at the dist. roter to make sure that it is pointing at the #1 spark plug wire. I could get 180 out of time. If you do it right it should start up right away. then you can use a timing light to finish it.
Good Luck jerry1938@hotmail.com

Posted on Dec 13, 2008

Ad
flacooo1
  • 172 Answers

SOURCE: 1996 timing belt changed, lined up all the marks,

Hi my name is juan and lets try to solve this it is possible that when you rotated the camshaft the distributor last his position and this is why it won't start it may not be the problem but this happens a lot so open your distributor and aline up your marks on camshaft and the crankshaft then make sure the distributor is pointing near the #1 spark plug if is opposite give it a 1 more turn to the crankshaft line up your marks again and se what happens #1 spark plug is the closets to the front part of the engine on 4cil

Posted on Mar 26, 2009

steve_baldam
  • 52 Answers

SOURCE: timing belt broke on mazda 5

Think you have to put a flat bar across the back of the cam shafts same as the old ZETEC ford motors. Failing that are the vernier pullies marked with eithr O T or do they have a - or a . that line up with a position on the end of the cylinder head.

Posted on May 12, 2009

  • 1757 Answers

SOURCE: mazda b 2500 how to set timing when the timing belt has broken in

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Timing Belt and Mark(s) Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/1998/make/mazda/model/b2500/1998_mazda_b2500_timing_belt_diagram_marks.htm

Posted on Mar 07, 2010

  • 1 Answer

SOURCE: how do you time a 4 cyl, and a diagram for those timing marks locations

if u go on yahoo.com type 1995 mazda 626 timing and click on search images you will see a picture of how to set it.

Posted on Dec 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reroute the drivibg belt or fan belt


Hi,just inline the crankshaft to the top dead centre marks,then check that the camshaft marks line up,if they dont line up then turn the crankshaft pully again untill the camshaft marks line up,slacken the timeing belt pully adjuster take belt off and replace with new one,tighten the pully adjuster back up,now put a spanner on the crakshaft pully and turn clockwise untill the top dead centre marks and the camshaft marks inline if they dont then slacken the ajusting pully inline marks again and try again,if marks do inline ok then you are ready to start the car.
hope this helps good luck.

Feb 25, 2015 | Cars & Trucks

1 Answer

Set camshaft timing


there should be marks on crank pully and cam belt pully. rotate motor until crank pully timing mark is on zero.the cam belt pully should be lined up with its own mark.number one piston should be at the top of its stroke (top dead centre TDC) and number one valves should be shut. if the cam belt mark is not alined with its own mark remove the belt realine the marks and refit the belt

Sep 15, 2013 | 1993 Subaru Legacy

1 Answer

Is a mazda protege es 2000 1.6l pump gaz changed,spark plug is new , coil is ok, the mark for timing is ok (2cam)but not sure for crank mark i know is the pin on the crank supposely up ,the motor turn but...


If I understanding right, you set the timing on your mazda. you may have set timing on the exhaust stroke. Rotate the crankshaft again with the belts off and realign the timing marks. You need the number 1 cylinder top dead center on the compression stroke not the exhaust stroke. Also take off distributor cap and make sure rotor is pointing toward number 1 cylinder spark plug wire when at top dead center. Hope this is what you were asking.

Aug 21, 2013 | Mazda Cars & Trucks

1 Answer

1997 honda accord need diagram for timing belt marks


need help putting my 1997 honda accord in time.I got the cam pullie on top and crank top dead center.does the oil pump gear haft to go straght up too.and one more thing when we get the belt on it keeps tring to roll offneed help bad.Can anybody help please?

Jul 19, 2012 | Cars & Trucks

1 Answer

How do I know when my camshafts are top dead center the outter timing pulley was loosened stupidly before we could mark anything


Not to worry. The cam gear has marks on it already. When the cams are aligned at Top Dead Center (TDC) the keway for the pulley will be pointing UP and the marks on the edge of the pully will be lined up with the valve cover sealing surface of the cylinder hed. (See picture below)

3_18_2012_9_32_43_pm.gif

Mar 18, 2012 | 2000 Hyundai Elantra

1 Answer

WHAT IS THE TIMING AND WHERE ARE THE IGNITION TIMING MARKS ON A 1958 S1 BENTLY


down on the fromnt of the motor were the main belt pully on one side of the motor is some marks "ubove top dead center and below top dead center" as well there is some marks on the block were the distributer is that allows you to goven your timing as well

Dec 31, 2011 | Cars & Trucks

1 Answer

Hi i need to know 2001 ford taurus top dead centre mark on crank pully


  • Due to the lack of timing marks you need to remove the center bolt from the damper on the crankshaft and take a flashlight or a laser pointer and look at the keyway for the damper and point the keyway to 12 O'Clock and that is Top Dead Center.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jul 19, 2011 | Ford Taurus Cars & Trucks

1 Answer

How do i know if i have my timing chain on correct?


okay first you make sure the timing marks on the pullys or gears are lineing up also you find #1 cylinder pull out spark plug place a long phillips head scew driver into the hole turn the main crank it should rise and fall get the lower part of the engine to where the scew driver stops rising and right before it falls you should be at top dead center on the lower part of the engine. turn the cam shaft till the timing mark on the pully or gear is at top dead center (TDC). but you should have timing marks on the crank shaft pully and the cam shaft gear or pully I recomend a chiltons or haynes manual so you can locate these marks.

Oct 31, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

Timing gear mark 94 dodge shadow


Look at this and see if this is how you did it. If that's not your engine you can enter your info to see it.

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528025169f

Aug 03, 2010 | 1994 Dodge Shadow

1 Answer

Timing marks1994 s10 blazer v-6 4.3 litter


Hi: I assume your trying to locate your timing marks. On the Bottom Pully on your Engine where your Belt or Belts run, Behind where the Pully is Mounted to is your Harmonica Balancer ,On that Harmonic Balancer you'll find your Timing Marks,Clean it all the way around it with a Degreaser wipe it off rotate your enging a bit at a time and line up your timing marks with the Pointer which you'll also see ,It just looks like a half Triangle or a Round Pin. Pointing towards your Timing Marks. TDC =Top Dead Center.

May 28, 2010 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?
2005 Mazda 3 Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...