Question about 1998 Dodge Avenger

Open Question

Belt diagram 1998 dodge avenger

Belt diagram

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
localwonder
  • 6784 Answers

SOURCE: diagram for a serpentine belt replacement for 2000 avenger dodge

HI. i have posted the diagram requested below.

7109f62.jpg

Posted on Aug 24, 2009

Testimonial: "This was exactly what we needed, Thank you so very much. "

Ad
  • 416 Answers

SOURCE: 1998 dodge avenger tranmission control solenoid

Below the link for Chrysler/Dodge auto-transmission manual
http://www.scribd.com/doc/7095618/545rfe-Transmission-Manual

Solenoid mounts outside the transmission, so you do not need to remove the transmission to install. It should be located between fuse box and air filter housing on the top of transaxle case and right next to transmission controle module.
I hope his step by step procedure will work for you. It is not hard at all to replace the solenoid. There are three 10mm bolts. You will also need to remove the input speed sensor. One thing to look out for is not bending the gasket when installing the new solenoid:

  1. Disconnect battery negative cable.
  2. Remove air cleaner assembly.
  3. Remove electrical connectors for transmission control module (please refer the manual I send you and autozone.com website).
  4. Remove the Transmission Control Module
  5. Disconnect and remove the input speed sensor
  6. Disconnect the transmission oil cooler lines. Cap off hoses and fittings to prevent foreign matter intrusion.
  7. Disconnect the solenoid/pressure switch assembly connector.
  8. Remove the three solenoid/pressure switch assembly-to-transaxle case bolts
  9. Remove solenoid/pressure switch assembly and gasket

Keep everything clean to prevent foreign materials to go inside
  1. Install solenoid/pressure switch assembly to case using a new gasket
  2. Install bolts and torque to 13 N·m (110 in. lbs.)
  3. Install 8-way connector and torque screw to 4 N·m (35 in. lbs.)
  4. Uncap and install transmission oil cooler lines.
  5. Install input speed sensor and torque to 27 N·m (20 ft. lbs.)
  6. Install Transmission Control Module
  7. Install air cleaner assembly.
  8. Connect battery negative cable.

P.s. 1. You can fine some clips on YouTube.com at least for similar cars
2. Also at Autozone.com you can find the component location for your car and repair guide
3. Also there is a link for Mitchel1 online manual useb by US mechanic 1 week subscribtion is
11.99 , 1 month 16.99
http://www.2carpros.com/kpages/auto_repair_manuals.htm
Let me know if you need more info
Good Luck and happy fixing

Posted on Jan 24, 2009

c17hydro
  • 2984 Answers

SOURCE: 1998 Dodge Avenger serpentine belt issue

What size of motor, do you have a/c and which belt are you replacing? Not sure about your engine size since you did not list it so please pick the applicable motor:

Sebring Coupe And Avenger (2.5L VIN N Engine)

  1. Disconnect the negative battery cable.
  2. Loosen the tension pulley locknut.
  3. Rotate the adjusting bolt to decrease the belt tension.
  4. Remove the drive belt from the engine.
To install:
  1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
  2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
  3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
  4. After the belt is installed and adjusted properly, tighten the locknut to 17 ft. lbs. (23 Nm).
  5. Connect the negative battery cable.

2.0 DOHC

Power Steering Pump And A/C Belt
  1. Disconnect the negative battery cable.
  2. Loosen the tension pulley locknut.
  3. Rotate the adjusting bolt to decrease the belt tension.
  4. Remove the drive belt from the engine.
To install:
  1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
  2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
  3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
  4. After the belt is installed and adjusted properly, tighten the locknut.
  5. Connect the negative battery cable.

Posted on Oct 29, 2009

  • 1757 Answers

SOURCE: Need diagram/schematic for serpentine belt replacement

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...

http://www.2carpros.com/car_repair_information/year/1998/make/dodge/model/ram_van/1998_dodge_ram_van_drive_belt_routing_diagram.htm

Posted on Mar 08, 2010

  • 31 Answers

SOURCE: i need a diagram of

There should be a diagram under your hood on the radiator support.

Hope this helps

Posted on Aug 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone have the specs for a 1998 dodge avenger 2.5 torque head bolts


Go to autozone.com and make a free account. Put in the year make and model and look for the free repair guides.

Sep 12, 2014 | 1998 Dodge Avenger

1 Answer

2008 dodge avenger serpentine belt diagram


Is it not on top of your radiator area, or underside of hood? What engine?

Apr 19, 2013 | 2008 Dodge Avenger

2 Answers

Belt route 2011 dodge avenger


I find this diagram that I hope that help you...


10_3_2011_12_27_53_am.jpg

Oct 02, 2011 | 2011 Dodge Avenger

2 Answers

2.4 Dodge avenger belt Diagram


I find this diagram AVENGER Engine L4 2.4L 2360cc 144ci GAS FI N K that I hope that help you...


10_3_2011_1_14_07_pm.jpg

Oct 02, 2011 | 2011 Dodge Avenger

1 Answer

1998 Avenger: can't find fuel pump fuse on 1998 dodge avenger...


You will find the fuel pump inside the fuel tank. Hope this will help.

May 17, 2010 | 1998 Dodge Avenger

1 Answer

1998 Dodge Avenger serpentine belt issue


What size of motor, do you have a/c and which belt are you replacing? Not sure about your engine size since you did not list it so please pick the applicable motor:

Sebring Coupe And Avenger (2.5L VIN N Engine)
  1. Disconnect the negative battery cable.
  2. Loosen the tension pulley locknut.
  3. Rotate the adjusting bolt to decrease the belt tension.
  4. Remove the drive belt from the engine.
To install:
  1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
  2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
  3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
  4. After the belt is installed and adjusted properly, tighten the locknut to 17 ft. lbs. (23 Nm).
  5. Connect the negative battery cable.

2.0 DOHC

Power Steering Pump And A/C Belt
  1. Disconnect the negative battery cable.
  2. Loosen the tension pulley locknut.
  3. Rotate the adjusting bolt to decrease the belt tension.
  4. Remove the drive belt from the engine.
To install:
  1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
  2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
  3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
  4. After the belt is installed and adjusted properly, tighten the locknut.
  5. Connect the negative battery cable.

Oct 29, 2009 | 2000 Dodge Avenger

1 Answer

I need to install a belt on my husbands 1998 dodge avenger


you can go to most any part stores and get the diagrahm

Aug 17, 2009 | 1998 Dodge Avenger

1 Answer

I need a diagram for the serpentine belt without a/c on a 1996 dodge avenger


should be under the hood some where or in the owners Manuel if you havent looked in those places i would try that first

Jul 06, 2009 | 1996 Dodge Avenger

Not finding what you are looking for?
1998 Dodge Avenger Logo

Related Topics:

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...