Question about 2000 Ford Expedition

Open Question

P1000 code for a 2000 ford expedition - 2000 Ford Expedition

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chrischronic
  • 235 Answers

SOURCE: 1997 FORD CODE P1000

a p1000 code means that the system has not run all checks since last memory erase. in other words after a code erase this code is set until the car has been driven for 2 drive cycles which is 20 to 25 miles then 20 to 25 miles again.

Posted on Apr 21, 2009

01fordeb
  • 1033 Answers

SOURCE: Door locks on Ford Expedition stuck

Look under your steering wheel right under the dash. There should be a small white strip with 5 numbers. This is your master code for your vehicle. If you bought the car used and they give you a code, they could have made their own code, but the master will override it. If this don't help, the module for the doors may be going bad.

Posted on Jan 05, 2010

moparownr
  • 667 Answers

SOURCE: No heat in my 2000 ford expedition

You should check your blend door, go to the center of your dash look down towards the floor right at the bottom on the hump (tunnel area) you will see a black or same as interior color, cover it has small slits cut in it, it is held in by two expanding type plastic bolts, they do not unscrew, just pull them out, one on each side. Once removed locate the white small box with a wiring harness connected to it, a little to the right hand side. This is the stepping motor that controls the blend door. Remove the stepping motor, and reconnect the harness, look at the motor drive unit and operate the heater control knob, does the motor turn, if it does then use a mirror and look at the drive end of the blend door itself, it is probably broken. If the door is broken, this repair just got difficult, the entire dash will have to be removed to access the environmental station, once accessed there are about 10 screws that hold the top cover on the enviromental station, undo these screws and remove the top cover, then you can remove and replace the blend door. If you are not comfortable with this difficultly level in repair I suggest you seek out your favorite local shop. removing the dash is not easy, there are alot of screws, some in very difficult places to reach. Testing the motor is easy. I hope this helps, let me know.

Posted on Jan 20, 2010

  • 451 Answers

SOURCE: 1998 Expedition: 2000 Ford Expedition I smell antifreeze with heate...

If you smell antifreeze it may be 3 possibilities: 1. you may have a leaking hose/hose connector , or water pump. 2. your heater core is bad and needs replaced. Unless you know what you are doing I would highly suggest taking to dealer for heater core replacement. The dash and steering colum has to be removed to get to the heater core. This is not an easy job believe me (about-900-1200 job). If you have your heater core replaced then also replace the climate control door. This is good preventative maintenance and also a a dollar saver. I would have a pressure check run on your radiator as a first thought. All you may have is a bad hose and that can easily be replaced.

Posted on May 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My car won't start and is showing a p1000 code . What does this mean?


P1000 is a manufacturer specific fault code:

Ford P1000: OBDII Monitor Testing Not Complete.
Jaguar P1000: Engine control module (ECM) - internal error.
Kia P1000: System diagnosis incomplete.
Land Rover P1000: Engine control module (ECM) memory erased - no codes stored.
Mazda P1000: OBDII Drive Cycle Malfunction.

So depending on the manufacturer of your car would depend on the meaning of a P1000 code!

Jan 21, 2015 | Cars & Trucks

1 Answer

Engine code p1000


P1000 simply means that the computer has not completed all the self tests...once you get in enough tests that code will go away.

Jul 22, 2014 | 1997 Ford Expedition

1 Answer

What does code p1000 mean on 97 experdition 4x4 5.4 motor


It means the motor hasn't completed it's drive cycle. If you've had work done and the battery was disconnected it sometimes trips the code. If it doesn't go away by itself after about 30 miles or so you might need to get the computer reset at a shop.

Jul 22, 2014 | 1997 Ford Expedition

1 Answer

I need the code sheet for a 2000 expedition


Just use google ---to find any codes

2000 expedition obd2 code P1450

Feb 10, 2013 | 2000 Ford Expedition

1 Answer

P1000 trouble code


means that the OBD-II monitor testing is not complete.

Potential causes of a P1000 include:
The battery or PCM has been disconnected
The diagnostic trouble codes have been cleared

You can ignore this code and it should go away as part of normal driving.

Jan 10, 2013 | 2004 Ford Expedition

1 Answer

Code p1000


this obd2 trouble code table can help you understand the meaning of code.

Sep 05, 2011 | 2001 Ford Expedition

1 Answer

Where is cylinder 1 located and what is a p1113 trouble code it has something to do w/emissions


Code P1113 IAT sensor (L/C) open/short circuit; just replace this part.

About the firing order, check...

2000 Ford Expedition 4.6 liter SOHC V-8 VIN "W"

4403b68.gif


2000 Ford Expedition 5.4 liter SOHC V-8 VIN "L"

4f90733.gif

Mar 29, 2010 | 2000 Ford Expedition

1 Answer

1997 FORD CODE P1000


a p1000 code means that the system has not run all checks since last memory erase. in other words after a code erase this code is set until the car has been driven for 2 drive cycles which is 20 to 25 miles then 20 to 25 miles again.

Apr 20, 2009 | Ford Taurus Cars & Trucks

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...