Question about Cars & Trucks

1 Answer

Need to see how timing marks are on a 95 liteace 5k engine

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Those who needs a liteace manual u can e mail me at rbdelizo@yahoo.com :)

Posted on Nov 26, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find the location of engine number for toyota liteace ?


main places ,if a 4/4 then its on the chassis at the rear above the back wheel ,but if a car it could be under the spare wheel in the boot or front floorpan or under the seat RH side ,cannot say i can look this one up in m,y all data book as never heard of a liteace ,

Apr 02, 2016 | Toyota Cars & Trucks

1 Answer

Where should the time chain dots be on 5k toyota engine if the no 1 piston is in fire position


comment on the engine capacity . make and model and year and you may get an answer to the question as a 5K toyota engine could be in things other than cars

Sep 06, 2015 | Toyota Cars & Trucks

1 Answer

5k toyota timing chain marks


Place the marks in the position before removing the chain with the ignition timing mark on TDC do not move any thing after you remove the chain until the new chain is back on.

Nov 04, 2013 | Cars & Trucks

1 Answer

On the crank mark on my festivs 95 where do i line it up with the plastic mark on the engine, on the first mark, in the middle or on the other mark? it keeps throwing itself out of timing. Is this to do...


This is a general view of the timing marks on the engine and the pulley, yours may not be the same but should be similar enough.

images?q=tbn:and9gcs1xg29mxl9_sakzrhjrhl9kkxpb5g-farkjjf_zy39dk3yjisnoaEvidently the timing angles should be on a placard within the engine compartment but are somewhere between 10 and 15 degrees BTDC. To set it correctly you need a timing light and remember to tighten the clamp on the bottom of the distributor on completion, This is probably why you timing is throwing itself out.

Mar 13, 2011 | 1990 Ford Festiva

1 Answer

Set timing on a 1992 honda prelude, 2.3 engine, I REPLACED THE DISTRIBUTER AND NOW ITS COMPLETELY OUT OF TIME, detailed instructions please


  1. Locate the service check connector and, if applicable, remove the cap. On 1988-91 Preludes, the cap is yellow and the connector is located next to the vacuum control box in the engine compartment. On 1992-95 Preludes, the service connector is located under the middle of the dash. On 1990-93 Accords, the connector is blue and is located behind the right front kick panel, under the dashboard. On 1994-95 Accords, the service connector is located behind the glove box. Use a jumper wire to connect the two terminals of the service connector.
  1. Following the manufacturers instructions, connect a timing light to the engine. The positive and negative leads connect to their corresponding battery terminals and the spark plug lead to No. 1 spark plug wire.
  2. Make sure that all wires are clear of the cooling fan and hot exhaust manifolds.
  3. Set the parking brake and block the front wheels. Start the engine. Check that the idle speed is set to specifications.
  4. Point the timing light at the timing marks. On all models except 1994-95 Accords, the marks are on the flywheel. On the 1994-95 Accords, the timing marks are on the crankshaft pulley. When the engine is idling, the red mark must align with the pointer. Some timing marks are indicated by 3 lines; the center one must be aligned with the pointer.

  1. If necessary to adjust the timing, loosen the distributor hold-down bolt(s) and/or nut and slowly rotate the distributor in the required direction while observing the timing marks.
  2. To complete the adjustment operation, tighten the hold-down bolt, taking care not to disturb the adjustment.
  3. Switch the engine OFF . Reinstall the rubber plug in the timing window and remove the timing light. Remove the jumper wire.



0900c1528005f368.jpg

Fig. Fig. 4: Service connector on 1988-91 Preludes


0900c1528005f36b.jpg

Fig. Fig. 5: Service connector on 1992-95 Preludes

Mar 03, 2011 | 1992 Honda Prelude

1 Answer

Replacement of timing chain toyota 5k engine


Theres (if mounted correct!) two MARKS on the sprockets~these fit with the bright links on the chain~just in case anybody else needs it...

Love from Capt. Whodooooooooooo.

Mar 21, 2009 | 1995 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...