Question about 1999 Ford Escort

1 Answer

Escort headlamp removel

Do i have to remove the bumper to remove head lights

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 73 Answers

In most cars yes, thsi is not hard as it may seem, maybe takes abut 3 minutes all up. either way look around the fornt end and you will work your soluton.

Posted on Oct 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kia carens head light removel


The question was answered earlier. Please check within the bonnet to find the headlamp assembly to be removed and reset.

Nov 22, 2011 | Kia Cars & Trucks

1 Answer

Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.
  • Remove the front fascia extensions, if equipped.
  • Remove the front fender liners.
  • Remove the fog lamps.
  • Remove the bolts (4) from the front bumper fascia (3) at the fender.


506bafd.gif

Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    How to change the headlight on a 2004 bmw 5 series


    if you have an entire headlight assembly (in case of accident) remove bumper, there are 8mm screws on the inner lining of the fron wheel well where the fender plastics and the air dam connect to the bumper, undo the screws concerning the bumper on bot sides of the car. then remove the plastic cover under the bumper (either philips screw heads or 10mm) and then under the aluminum re-enforcement strip behind the bumper (access from under the car) remove the torx screws that hold the bumper aluminum to the car frame, get a friend to help you pull the bumper off evenly an then seek the 8mm screws that hold the headlamp in place. the headlamp comes off the car strait out the direction of the front. disconnect the wires and connect the new lamp and fasten to the car. then do the assempbly in reverse order for the bumper installation.
    for just changing the bulb, there are some rubber seals behind the light where the bulb rests. there are metal clips than you depress to release the bulb. install a new bulb and then replace the rubber caps.

    Nov 07, 2009 | 2004 BMW 5 Series

    1 Answer

    Much "moisture" inside Left, (Passenger- Side) headlamp housing (extends into the parking light area,......................Isuppose I'll have to remove the assembly but ,.........HOW,..............is the...


    There will be two screws along the top of the assembly and two screws along the bottom of the assembly (these screws can either be reached from the back of the assembly or you'll have to reach up and under the bumper to get to them, can't remember exactly)

    Aug 18, 2009 | 1999 Ford Escort

    2 Answers

    Head lamp bulb chance on audi a6 2005?


    you need to remove the front bumer and you will see the head lamp bolts remove them and your headlamp unit is free as a bird.

    Jul 18, 2009 | 2005 Audi A6

    2 Answers

    Need to replace head lamps on Ford Escape 2001,


    there are 4 bolts that hold lamp in. the first 2 are obious. the others are behind the front bumper..the bumper must be removed to expose them...here is a cpoy of the manual to change..good luck

    Headlamp Assembly Removal and Installation
    1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
      Remove the front bumper cover. For additional information, refer to Section 501-19.
    1. NOTE: Pull headlamp assembly forward to access electrical connectors.
      Remove the headlamp assembly.
      1. Remove the three bolts.
      1. Loosen the nut.
      • Disconnect the electrical connectors.
      a0045726.gif
    1. To install, reverse the removal procedure.
      • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

    Apr 22, 2009 | 2003 Ford Escape

    2 Answers

    Need to replace headlight assembly on 2005 Ford Escape


    ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..

    n0037234.gif
    Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
    Removal and Installation
    NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.
    1. Remove the front bumper cover. For additional information, refer to Section 501-19.
    1. Remove the 3 headlamp assembly bolts.
      • To install, tighten to 5 Nm (44 lb-in).
    1. Remove the headlamp assembly nut and the headlamp assembly.
      • Disconnect the electrical connectors.
      • To install, tighten to 5 Nm (44 lb-in).
    1. To install, reverse the removal procedure.

    Jan 01, 2009 | 2005 Ford Escape

    2 Answers

    Audi a4 front lights


    if you mean the complete light you will have to remove front bumper then you will get to the bottom bolts that hold the headlamp in.....

    Oct 24, 2008 | 2003 Audi A4 Cabriolet

    1 Answer

    Headlamp replacement


    you dont need to disconnect battery, just remove the front grill as there is a bolt hiden behind that, there is a bottom bolt on the lamp and you may need to drop the bumper slightly to get to this, this is easy just remove the 2 crosshead screws by the wheel to drop the bumper slightly.

    Oct 22, 2008 | 1997 Ford Escort

    1 Answer

    Replacing headlamps


    you shouldnt have to

    Aug 20, 2008 | 2000 Ford Escort

    Not finding what you are looking for?
    1999 Ford Escort Logo

    Related Topics:

    67 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    60867 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...