Question about 2007 Chevrolet HHR Special Edition

1 Answer

T/C light stays on all the time

Hard shfiting i changed out the Air flow sensor and new air filter

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

Hi there:
Did you get codes from the PCM? You did not say the check engine light was on.

If the Tracation Control light is coming on, the tracation control is activating and can cause a jerking problem. Nothing last the life of the vehicle, however the timing chain should not need to be changed at 49,000 miles. If it does, I would have them do it under warranty. See if you can get the codes and send them to me. That way we can get a better ideal of what is going on. Could you please tell me what these codes stand for?

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Posted on Feb 15, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: having problems with my 96 chevy tahoe mass air flow

The MAF (Mass Air Flow) sensor is a very common problem with these along with the pickups. This isn't what you would call an inexpensive part. Definitely do some shopping before you buy one.

Posted on Nov 10, 2008

JShreader
  • 50 Answers

SOURCE: locating the iat sensor on a chevy tahoe 2008

Yes. That is exactly it. The Air Intake Temp Sensor is built into the Mass Air Flow Sensor on the Air Filter Box. Below is a picture...
29f8daa.jpg
6d7178d.jpg
I personally have not connected one of these Chips to a Tahoe...What I can provide you with, is the Connector Diagram so you know exactly what Wires you need to Splice in to. See below...
ce630fe.jpg
I hope this helps you. If you have any more questions or need any more diagrams, please don't hesisitate to ask...Thanks again, JShreader.

Posted on Mar 31, 2009

  • 39 Answers

SOURCE: mass air flow sensor bad on 2002 monte carlo ss

It's should be a simple remove and replace. Just make sure the engine is off. Also do not touch any of the filament wires on the sensor, just the plastic housing. Also after you install it drive the car for a little while (city speeds, cruising speeds and inbetween). That way the computer will be able to readjust its setting since it is a new sensor.

Posted on Apr 02, 2009

SOURCE: the heater control does not change the air flow to

Check any vacuum hoses from engine all the way to heater/a/c housing under dash,for leaks. Then manually move or put a vacuum guage on every vac motor you can see and get to. Your working your way back to the switch. If you want to you could start at the switch but % wise and degree of difficult your better to back in. Now a schematic will make the process easier. Hard to work on a system you don't know .Electrical or Computer sometimes play into these, I have an older S10 so no computer.

Posted on Sep 29, 2009

  • 5 Answers

SOURCE: looking to findthe mass air flow sensor on a 89 chevy corsica

location is under the hood where the aircleaner is there is an electrical connection that plugs into the mass air flow sensor

Posted on Oct 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ok, i have a 2000 sierra 5.3 slt got the p0101 code it wouldnt star up unles i give it some gas and it shots off so, rough idle and wont stay on, i change the MAF sensor (new delphi) but still doing the...


The Mass Air Flow (MAF) sensor is located in the stream of intake air and measures this intake flow rate by measuring a part of the entire intake flow. It is what they call a hot film and is supplied with electric current from the Engine Control Module (ECM).
The temperature of the hot film is controlled by the ECM to a certain extent. The heat generated by the hot film is reduced as the intake air flows around it. The more air, the greater the heat loss. Therefore, the ECM must supply more electric current to maintain the temperature of the hot film as air flow increases. The ECM detects the air flow by means of this current change.
The OBDII people suggest that before you replace the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with compressed air or by using a cleaner on the mass air flow sensor. Truly, all that may be wrong is a build-up of dirt.Unfortunately, in your case, replacing the Mass Air Flow did not work.After replacement, did you reset the code and drive the vehicle?.
I suggest you replace the air filter and check for intake air leaks.YouTube has some good videos on how to do this, one by Eric the car guy and one by Scottie Kilmer https://www.youtube.com/watch?v=9CPqbaSgcokhttps://www.youtube.com/watch?v=zMok2y05jNE

Jan 13, 2015 | 2000 GMC New Sierra 1500

3 Answers

2003 Nissan Altima 2.5L Service Engine Soon Light is on, Auto Zone says codes are for MAF and O2 Sensors. Car hard to start after driving a while but when starts appears to run smooth. Auto Zone thi


ok lets start with the codes they say your getting. P??? which 1's and how many. there are few o2 sensors, are they next to the Exhaust next to the converter? MASS AIR FLOW -MAF use this, for now i am guessing, until i see the correct codes your are getting. this could be the 1 you may have below, please read it........
  • P0103
    Mass Air Flow Sensor Circuit High Input
  • Possible causes
  • Faulty mass air flow sensor
    - Intake air leaks
    - Dirty mass air flow sensor
    - Dirty mass air filter
    - Mass air flow sensor harness is open or shorted
    - Mass air flow sensor circuit poor electrical connection
  • Before replacing the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with low compress air or mass air flow sensor cleaner. Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor.
  • possible symptoms Engine Light ON (or Service Engine Soon Warning Light)
    - Engine stall
    - Engine running rough
    - Excessive fuel consumption
    - Excessive smoke
  • the code is generated when An excessively high voltage from the sensor is sent to Engine Control Module (ECM).
2003 NISSAN Altima Sedan OBDII Codes List

Oct 22, 2014 | 2003 Nissan Altima

1 Answer

2003 Grand Am Has P0102


It is not an ECM/PCM problem.
P0102 - Mass or Volume Air Flow Circuit Low Input
Possible causes- Faulty mass air flow sensor
- Dirty mass air flow sensor
- Dirty air filter
- Mass air flow sensor harness is open or shorted
- Mass air flow sensor electrical circuit poor connection
- Intake air leaks Tech notes Before replacing the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with low compress air or mass air flow sensor cleaner. Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor

Sep 27, 2012 | 2003 Pontiac Grand Am

1 Answer

ISUZU TROOPER 3.2 V6 CODE P0101


P0101 ISUZU - Mass Air Flow Circuit Performancexicon.jpghttp://engine-codes.com/p0101_isuzu.htmlForum CodePossible causes- Dirty mass air flow sensor
- Dirty mass air filter
- Mass air flow sensor harness is open or shorted
- Mass air flow sensor electrical circuit poor connection
- Intake air leaks
- Faulty mass air flow sensor
Tech notes Before replacing the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with low compress air or mass air flow sensor cleaner. Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor

Jul 04, 2012 | 2001 Isuzu Trooper

2 Answers

My 2000 ford focus has codes p0102 and p0113 whats that and what could it be?


P0102 - Mass Air Flow (MAF) Circuit Low Input
The MAF sensor circuit is monitored by the PCM for low air flow (or voltage) input through the comprehensive component monitor (CCM). If during key ON engine running the air flow (or voltage) changes below a minimum calibrated limit, the test fails. MAF sensor disconnected
MAF circuit open to PCM
VPWR open to MAF sensor
PWR GND open to MAF sensor
MAF RTN circuit open to PCM
MAF circuit shorted to GND
Intake air leak (near MAF sensor)
A closed throttle indication [throttle position (TP) sensor system]
Damaged MAF sensor
Damaged PCM
A MAF V PID (MAF PID) reading less than 0.23 volts (Refer to equivalent grams/second chart in GO to Pinpoint Test DC ) in continuous memory or key ON and engine running indicates a hard fault.
P0113 - Intake Air Temperature (IAT) Circuit High Input Indicates the sensor signal is greater than Self-Test maximum. The IAT sensor maximum is 4.6 volts or -50°C (-58°F). Open circuit in harness
Sensor signal short to power
Damaged sensor
Improper harness connection
Damaged PCM
IAT V PID reading greater than 4.6 volts with key ON and engine OFF or during any engine operating mode indicates a hard fault.

Nov 18, 2009 | 2000 Ford Focus

2 Answers

2004 denali check engine light stays on


There is no p01001, it's either p0100, or p0101.
Anyway, it's the mass air flow sensor that's bad. The p0171 and p0174 is a lean condition on bank 1 and bank 2, which are the oxygen sensors. Change the mass air flow sensor and that should take care of the p0171 and 74 codes.
The mass air flow sensor can cause the 02 sensors to read lean.
The u1301, is a class 2 circuit short to battery. That, you have to test wires to find with a voltmeter/continuity tester.
I would try and find that short before changing the flow sensor, you don't need the new one shorting out, they are not that cheap.

Nov 17, 2009 | 2004 GMC Yukon

2 Answers

My car won't stay on


your mass air flow sensor or throttle postion sensor is defective, buy one from a junk yard and try itthat way, I also think you can unhook the mass air flow sensor connecter and it should still run if it does then it's the mass air flow sensor. same thwith the throttle postion sensor unplugh it if it runs you will knowwhat the problem is it goes to base timing if it is unplugged.

Jul 18, 2009 | 2003 Pontiac Grand Am

3 Answers

Poor gas mileage 2000 S10 4.3L 4WD


Thats the mass air flow meter.Should get changed at 60.000 miles. Also change the air filter.

Jun 18, 2009 | 2002 Chevrolet Blazer

Not finding what you are looking for?
2007 Chevrolet HHR Special Edition Logo

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...