Question about Nissan Maxima

1 Answer

Manual clutch not working effeciently - Maxima Nissan Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 3,961 Answers

If the car has a few miles on it, the clutch may be worn. To test this, put the gearbox in 3rd and let the clutch out slowly while pressing the brake hard. The engine should stall immediately. If it runs on a bit before stalling, the clutch is worn.

At the other extreme, if the clutch is not releasing fully, which causes crunching of the gears, either the clutch hydraulic line needs bleeding, or the clutch cable needs adjusting up, whichever type it is.

Posted on Feb 15, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 honda civic 5 speed manual trans engine surges when down shifting from 2nd to 1st


Greetings & salutations Robert Avila,

(First question on FIXYA... Welcome).

Your engine surging and what gear you
"DOWN-SHIFT" to ... ought have very little in
common save for one condition (I can think of)...

Your clutch RELEASE is MARGINAL..!!

Check your master/slave clutch cylinders to see
if there is any leakage (fluid might also be low)...

These are not EXPENSIVE and USUALLY fail
in pairs...

If the surging happens with the clutch released... that
is a WORN CLUTCH DISC (replacement time)...

Actuator (slave)
2005 HONDA CIVIC 2 0L L4 Clutch Slave Cylinder RockAuto

2006
http://www.rockauto.com/en/catalog/honda,2006,civic,2.0l+l4,1432766,transmission-manual,clutch+slave+cylinder,2044

Activator + reservoir (Master)
http://www.rockauto.com/en/catalog/honda,2006,civic,2.0l+l4,1432766,transmission-manual,clutch+master+cylinder,1996

Else (not-so-easy (certainly doable))... CLUTCH DISC
http://www.rockauto.com/en/catalog/honda,2006,civic,2.0l+l4,1432766,transmission-manual,clutch+friction+disc,10605

Standard Information...
STOCK (less than $35 (assuming only wear)):
More Information for PACT 99661D

Honda is almost a DELIGHT to work on...
Mechanics manual is a MUST.

MOST IMPORTANT tip of this entry...

NEVER EVER ever let the weight of the transmission
be SUPPORTED by the input shaft...

You will be proud.

Carnac the Magnificent

Oct 23, 2017 | Honda Cars & Trucks

1 Answer

How to make mower stop when clutch/brake pedal depressed


Depending on the model and manufacturer of your mower, but it seems like the brakes are the problem.
I have a Murry and it has one disk brake on the rear wheel shaft. The master mechanism for this disk brake needed to be cleaned of dirt and grass clippings. In my case, this helped but brakes only 50% effecient so I use reverse when on an incline.

Mar 25, 2016 | Cars & Trucks

1 Answer

Hyundai Tucson 2009 high fuel consumption


There are a lot of factors that may contribute to high fuel consumption. Does the engine run ok during normal operation? Rough idle? Check engine light on? Have the oxygen sensors scanned for operating information to determine if the fuel system is operating effeciently by a qualified service center. These sensors monitor the effeciency of the fuel system

Oct 04, 2015 | Hyundai Cars & Trucks

1 Answer

Manual transmission will not disenage the clutch?


If you have a hydraulic clutch (slave cylinder to clutch fork) try bleeding it.
if it leaks you will have to replace it> If it is a manual clutch fork and the clutch starts to grab right off the floor the clutch is woen and will have to be replaced. You might also check the clutch rod for adjustment > in either case make sure the clutch rod is seated in the clutch fork.

Mar 24, 2012 | 1996 Honda Passport

1 Answer

My 09 HHR a/c quit working and is blowing hot air even when the fan is off. I hear a click coming from the dash right before it blows hot air. and today I noticed a hissing sound


That hissing sound is the vacuum line knocked off the servo that shuts off the heater core so the AC will work more effeciently. Your getting warmer.

May 11, 2011 | 2006 Chevrolet HHR

1 Answer

I owned a maruthi swift vdi in india.i heard that a hardware called chip tuning will increase performance in respect of speed and better fuel effeciency for diesel car.is it right??


Yes this is right for a lot of vehicles. But on the side the more your engine works with this extra power and acceleration the faster your engine and transmission will wear out.

Nov 19, 2010 | Suzuki Swift Cars & Trucks

1 Answer

My transmission seems to not shift properly. I


forget the manual and throw it into back of garage ,now this expert ?? me only works on manuals because us spanish wouldnt give an auto box house room.Now if its not clearing properly when changing gear or its a job to get into first or reverse when stationary then its a new clutch job,some model cars have an adjustable clutch lever arm but if it gets to that stage where you have adjust it right out to get it to engage then its a new clutch time .Now hondas are not adjustable as such because they are hydraulic operated ,if it has clutch fluid then it sould work ok, but if the master cylinder is scored inside or the rubber is badly worn then could cause the problem ,get assistant to push clutch down and check movement on clutch arm ,if the arm starts to creep back when held down then the master cylinder needs changing ,but if it stays down then the clutch is worn even if it is not slipping ,the diaphragm spring clutch is going weak and the clutch plate isnt clearing ,or the clutch plate has heat distortion and its grabbing

Jan 03, 2010 | 1997 Honda Civic

1 Answer

Turn signal not working properly 88 new yorker


Check the flasher some Chyrs have split circuit when flasher goes bad it will effecy one side more than other.

Jun 16, 2009 | 1988 Chrysler New Yorker

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...