Question about Cars & Trucks

Open Question

Timing belt diagram 1992 volvo 940

Diagram timing belt 1992 volvo 940

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Junoon007
  • 1011 Answers

SOURCE: alternator belt replacement for 93 volvo 940

Preparation

Caution! Remove the ignition key.

Remove
the screw holding the engine stabilizer brace to the bracket on the engine
the screws holding the engine stabilizer brace to the suspension turrets
the engine stabilizer brace.

Applies only to B6xx4T engines:
Remove the plastic pipes between the turbocharger (TC) and charge air cooler (CAC) and between the air cleaner (ACL) and turbocharger (TC). Put them to one side. Remove the clamp from the intake manifold for the turbocharger (TC) for cylinders 1, 2 and 3. Turn the upper section of the pipe towards the firewall.

Relieve the load from the belt tensioner.
Remove the auxiliaries belt. See: Drive Belt\Service and Repair
Remove the upper timing belt cover.
Remove the front timing belt cover.
Lift up the servo reservoir and place it on top of the engine.Note! Ensure that the oil does not leak from the ventilation hole in the filler cap.

Seal the hose between the expansion tank and the radiator.
Disconnect the hose at the tank.
Lift up the expansion tank and place it on top of engine.

Raise the car. Remove
the right front wheel
the plastic nuts on the cover in the fender liner. Install the upper timing belt cover.
Turn the crankshaft clockwise until the markings on the crankshaft and camshaft pulleys correspond.
Turn the crankshaft a further 1/4 turn clockwise. Then turn back counter-clockwise until the markings correspond.
Remove the upper timing belt cover.

Remove the 4 vibration damper screws. Counterhold the crankshaft central nut.

Remove
the vibration damper
the auxiliaries belt
the belt cover behind the crankshaft pulley for the auxiliaries belt. Spray universal oil or similar around the rubber sleeve on the underside of the oil pump.

Remove the rubber sleeve.

Removing the timing belt

Slacken off the belt tensioner
Slacken off the center screw for the belt tensioner slightly.
Hold the center screw still.
Turn the tensioner eccentric counter-clockwise using a 6 mm Allen key.
Turn to 10 o'clock.
Unhook and remove the timing belt.Caution! Do not turn the camshafts or the crankshaft when the timing belt has been removed.


Checking the tensioner pulley and idler pulley Check bearing wear:
Spin the idler pulley and listen for noise. If replacing with a new idler pulley, tighten to 24 Nm .
Spin the tension pulley and listen for noise. When replacing, screw the tension pulley into place using the center screw.
Screw in the center screw by hand.
Ensure that the tensioner fork is centered over the cylinder block rib / bracket.
Ensure that the Allen hole on the eccentric is at "10 o'clock".

Installing the timing belt

Install the belt in the following order:
crankshaft
the idler pulley
intake cam
exhaust cam
water pump
tension pulley.Note! The variable valve timing unit on B6304S engines does not have a return spring. The unit is easily dislodged when reinstalling the timing belt.


Tensioning the timing belt

This adjustment is carried out on a cold engine. A suitable temperature is approximately 20°C / 68°F .
At higher temperatures (with the engine at operating temperature or a high outside temperature for example) the indicator is further to the right.
The illustration shows the position of the indicator when aligning the timing belt tensioner at different temperatures.
Carefully turn the crankshaft clockwise until the timing belt is tensioned. The belt must be in tension between the intake camshaft pulley, the idler pulley and the crankshaft.
Hold the belt tensioner center screw secure. Turn the belt tensioner eccentric clockwise until the tensioner indicator passes the marked position. Then turn the eccentric back so that the indicator reaches the marked position in the center of the window.
Hold the eccentric secure. Tighten the center screw to 25 Nm .
Check that the indicator is in the correct position.

Check

Press the belt to check that the indicator on the tensioner moves easily.
Install the upper timing belt cover. Turn the crankshaft 2 turns. Check that the markings on the crankshaft and camshaft pulley correspond.
Check that the indicator on the belt tensioner is within the marked area.

Finishing

Install the auxiliaries belt around the pulley on the crankshaft.
Install
the rubber sleeve on the underside of the oil pump
the vibration damper.
Use new screws.
Tighten to 35 Nm .
Angle-tighten 50°.
Use the crankshaft center nut as a counterhold
the plastic nuts for the cover in the right-hand fender liner
the right front wheel.

Lower the car.
the front timing belt cover. Tension the auxiliaries belt.
the expansion tank
the hose between the expansion tank and the radiator. Remove the lock grip pliers
the servo reservoir
the upper timing belt cover.

Applies only to B6xx4T engines:
Twist the intake pipe for the turbocharger for cylinders 1, 2 and 3 into position.
Tighten the clamp.
Install the plastic hoses between the turbocharger (TC) and the charge air cooler and between the air cleaner (ACL) and the turbocharger (TC). Tighten the hose clamps.

the engine stabilizer brace. Tighten to 50 Nm
the screw holding the engine stabilizer brace to the bracket on the engine. Tighten to 80 Nm .

Final check
Check and top up if required
coolant level
the servo fluid level. Test drive the engine.

Don't forget to rate the solution

thanks
good luck

Posted on Oct 11, 2008

Ad
pstallworth
  • 1 Answer

SOURCE: 940 GL Stall problem

My 1992 940 Turbo has had stall problems. On the two last occasions I replaced hoses, which solved my problem.

Posted on Oct 15, 2008

Junoon007
  • 1011 Answers

SOURCE: 1994 Volvo 940 timing belt

http://caunter.ca/volvo960/ip14814.pdf

check this pdf with illustrations

thanks
good luck

Posted on Dec 24, 2008

nyspeter86
  • 81 Answers

SOURCE: 1992 Honda Prelude Timing Belt Diagram

There's no such thing as a timing belt diagram.

Do you mean to say the "Procedure" for changing a timing belt in a 92 Prelude?

By asking such a question I can only interpret it as a clear indication that you've never changed a timing belt before.

If this is true, then you don't want to start out or practice on your own car.

Get the car to a pro and have the job done right.

If not true (and you've changed timing belt's in the past)

Then give me the engine size and I'll post the:

"PROCEDURE" for changing the belt in a few hours.

Posted on Dec 31, 2008

  • 1 Answer

SOURCE: 93 Volvo 940 Threw timing belt, now won't start

The same thing happened to my 94 volvo 960 the engine belt was having the same problem, i changed it the belt, it was fine for a few miles after that it just died, does not fire, not sure if it is getting fuel, but the mechanic says the timing belt went off. you may have to check the crank sensor on yours.

enrixba

Posted on Jun 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need diagram of timing marks and belt allignment for 1992 volvo 940


best thing you can do is buy a repair manual at any autoparts store .

Feb 15, 2012 | 1992 Volvo 940

1 Answer

Belt Routing Diagrams


For belt routing diagrams of 1992 volvo 940. Click the link below:--- http://technoanswers.blogspot.com/2011/10/timing-belt-diagram-for-1992-volvo-940.html ----------- Its with proper detail and procedure. ----- This will help.Thanks.Helpmech.

Oct 24, 2011 | 1992 Volvo 940

1 Answer

I have a volvo 940 1992 non turbo and sometimes it won't start


you have to check you engine starter (dispositive that is made to turn on your car)

Jul 30, 2010 | 1992 Volvo 940

1 Answer

What is the engine size for a 1992 940 volvo


Turbo or non turbo engines are 2.3 liter.

May 20, 2010 | 1992 Volvo 940

2 Answers

Replacing fuel pump on 1992 Volvo 940


look in autozone, look up the part n then click on "view job diagram" hope that helps

Feb 28, 2010 | 1992 Volvo 940

1 Answer

Volvo 940 gl reg j93 has 1992


i had the same problem with my 1994 940 volvo

i called a dealership in town and asked nicley,gave them the vin and they looked up the code and told me. online im not sure where to look it up, but if you call its a chep fix

Jan 13, 2010 | 1994 Volvo 940

1 Answer

Timing belt replacement


Sorry for the delay.
I am personally going back to answer your unanswered question. I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt/MARK(S) Diagrams that you will need.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1994/make/volvo/model/940/1994_volvo_940_timing_belt_diagram_marks.htm

Jul 30, 2009 | 1994 Volvo 940

1 Answer

1992 volvo 940 turbo died while driving and will not start


two things to check,,, there is a crank sensor at the back of the engineby the bulkhead,,at the top of the engine where the gearbox joins ,,,the sensors are known to be faulty if sometimes ,,, check the cable to the sensor,,if it is damaged replace the sensor,,,the other common problem is the fuel pump relay,,, behind the fusebox in the dash

Nov 16, 2008 | 1992 Volvo 940

1 Answer

1994 volvo 940


what belt?timming belt, alt belt,etc?

Jul 24, 2008 | 1994 Volvo 940

5 Answers

940 GL Stall problem


crank sensor problem

Jun 16, 2008 | 1992 Volvo 940

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...