Question about Cars & Trucks

1 Answer

Had decayed tooth extracted and still have bad breath

I am also rinsing with mouthwash after every meal, still there ;o

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 202 Answers

Pull the rest of them !!!!!!

Posted on Feb 15, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

What cause bad breath and how to get rid of it?


see you doctor
halitosis ( bad breath ) can be from gum disease, throat disease, health problems , smoking, gastric reflux, bad teeth and lots of other reasons
use a quality mouth rinse before brushing and use a powered toothbrush as they do a better job than your hand

Sep 23, 2016 | Cars & Trucks

2 Answers

My check engine light is blinking and the car is putting when you press the pedal also when the car is not moving the engine shakes like the car is going to shut off please help


Sounds like a bad misfire/s. Could be plugs, wires if you have them, coil boots, coils, or coil packs. Check them one at a time(do a compression tests at the same time). If they all fire, suspect plugs or cylinder compression.

May 22, 2016 | Cars & Trucks

3 Answers

Does tooth extraction hurts?


This is car and truck repair?

Jan 29, 2015 | Cars & Trucks

2 Answers

Why dose the car stall out when it starts an to keep it runing i have to keep on the gas?


sounds like a possible exhaust system blockage. if the engine cant breath it wont want to run

Jul 26, 2011 | 1999 Oldsmobile Intrigue

1 Answer

I have a 88 grand marquis,not gettin fire to my


bet if u took the dist cap off it would look like tooth decay inside-n ur plug wires? replacing n inspecting these parts is the commonest overlooked tthing in toonups--chec fuel delivery for good measure

Aug 31, 2009 | 1988 Mercury Grand Marquis

1 Answer

HARD TO START IT FIRES FIRST TURN THEN STRUGGLES TO KEEP FIRING TO START UP THEN TAKES TIME TO FIRE UP,CAN SOMEONE HELP ITS DRIVING ME NUTS


chec ur distributer cap-bet the inside looks like tooth decay-inspec the whole ignition wiring-and dont forget fuel system maintenance

Aug 19, 2009 | 1988 Jaguar XJ6

1 Answer

Diesel engine (2c turbo inport from china)


gday im a mechanic i have owned two of these in a lite ace and a tarago there are three possitions that the cam shaft can be aligned and not have valve piston contact the middle one is the right one the two ither side of the correct one cant breath properly smokes badly ,idels rough and extreem lack of power and excessive noise (cam belt one tooth out ) same if injector pump is a tooth out but noisier. you need to remove the fan hub bracket to see the timing mark for the IP drive pully also the injector pump internals can be assembled 180 degrees out resulting in injection at bottom dead centre , extreem noise ,heaps of smoke and will barely move the car in first gear also the crank timing mark is only visible with the front harmonic balance flywheel and timing belt cover removed . answer to the other question why not a rover diesel . the 2ct ues heaps less fuel revvs heaps harder comes factory balanced is heaps quieter and lasts heaps longer there is no contest with the rover diesel the 2ct weighs less to the down side is that the turbo usualy fitted on the 2ct is under sized and very short lived. boosts early for low down torq but is unable to breath at the high revvs that this engine loves. turbo getts too hot at highway speeds and melts bearings if not warmed down . mine has a water cooled turbo of a 2.8 izuzu motor from a trooper/jackeroo im soon fitting this engine and turbo into 79 chrysler scorpion. this engine when decompressed to 17 to one with hot glow plugs handles 30 psi boost, you can get three different thickness head shims for this motor to decompress , ignore petro company propaganda ive done 300,000+ kms burning everything from lard mixed with alchohol to canola and sunflower blended with jet fuel ,petrol, sump waste oil a good injecor pump will feed an engine anything thicker than kerosine so long as its hot(80 to 100degrees c) even lard and sumpoil the thicker the oil the more lubricating and the longer the pump and injectors last so long as the oil is well filtered and free of water

fat power australia

Jun 03, 2008 | 2008 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...