Question about Cars & Trucks

1 Answer

Can't fine fan relay location for mustang 2005 v6

Fan cooling don't work

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Look inside under the hood of drivers side fender, you should see a rectangular black box that says fuses & relays.

Posted on Feb 14, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: fan cooling problem. which and where is the relay or fuse for the cooling fan? I need a diagram showing me what the relays are for and what they operate.

I have the original owners manual, and it says that there is a fuse (No 16) and a relay (No 10) for the blower motor. I've same troubleshooting right now. If you wants send me a email to luisfernandovaldes@hotmail.com to send you a scan imagen of the fuses diagrams.

Posted on May 04, 2009

Kravcar
  • 192 Answers

SOURCE: locate fan relay

There are three cooling fan relays in the fuse block under the hood.

b891122.gif


The fan relays above are numbered 37,39 and 40

Relay 37 is RH fan
Relays 39 and 40 are LH fan.


You can check if your fans are working by switching on the air con.
Are you having overheating problems?

Regards.

Posted on Apr 26, 2010

motor1258
  • 6674 Answers

SOURCE: 2005 vw jetta radiator cooling fan wont shut off

Check for a switch at lower part of rad. Should see a wire harness & plug on a sensor at bottom of rad. This sensor/switch also operates fan on/off according to coolant temperature. You may need to disconnect battery to get at it safely.

Posted on Jan 16, 2009

GM Elec
  • 1000 Answers

SOURCE: Where is location of cooling fan relay?

Under the hood on the drivers side, just forward of the shock tower, you will see what is called an "under hood fuse center". On the cover you can see the various fuses and relays that are located in the fuse center.
One of those relays is the coolant fan relay. Remove the top cover of the fuse center to gain access to the relay.
Hope this answers your question, good luck.
Regards,

Posted on May 02, 2009

Gozer
  • 435 Answers

SOURCE: 02 v6 mustang fuel pump relay location

The fuel system reset is located in the trunk on the drivers side just forward of the tail light behind the trunk liner.
You can go to this website and down load a manual for your car to get the fuse information. It starts on page 159, I was unable to copy the manual to the FixYa site.
https://www.fleet.ford.com/maintenance/owners_manuals/default.asp

Posted on Jun 01, 2010

Testimonial: "aaaaaaaaaaaaaaaaaa+++++++++++++++++thx"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cooling fan switch located on my 2005 malibu 3.5liter v6


Cooling fan switch ? The cooling fans (2) on that motor are controlled by three relays . A coolant temp. sensor gives temp info to the PCM - engine computer .
During high speed operation the PCM supplies the ground path for the cooling fan 1 relay through the low speed cooling fan relay control circuit. After a 3 second delay, the PCM supplies a ground path for the cooling fan 2 relay and the cooling fan S/P relay through the high speed cooling fan relay control circuit. This energizes the cooling fan 2 relay coil, closes the relay contacts, and provides a ground path for the left cooling fan. At the same time the cooling fan S/P relay coil is energized closing the relay contacts and provides battery positive voltage from the cool fan 2 fuse on the cooling fan motor supply voltage circuit to the right cooling fan. During high speed fan operation, both engine cooling fans have their own ground path. The result is a parallel circuit with both fans running at high speed.
The PCM commands Low Speed Fans on under the following conditions:
• Engine coolant temperature exceeds approximately 106°C (223°F).
• When A/C is requested and the ambient temperature is more than 50°C (122°F).
• A/C refrigerant pressure exceeds 1 310 kPa (190 psi).
• After the vehicle is shut off if the engine coolant temperature at key-off is more than 140°C (284°F) and system voltage is more than 12 volts. The fans will stay on for approximately 3 minutes.
The PCM commands High Speed Fans on under the following conditions:
• Engine coolant temperature reaches 110°C (230°F).
• A/C refrigerant pressure exceeds 1 655 kPa (240 psi).
• When certain DTCs set .
Watch this video ,it shows how it works !
Relay Driven Dual Cooling Fan Diagnostics

Nov 27, 2016 | 2005 Chevrolet Malibu

1 Answer

Cooling fans won't turn on. I replaced coolent


You need a wiring diagram

That would tell you what you did,as
you know what terminals you jumped

Then you look over the rest of the circuit
to continue

Your lucky you didn't short something out

Nov 21, 2012 | Cars & Trucks

1 Answer

Car's fan does not come on


try unpluging fan and apply power & ground to fan directly if fan runs you will need cooling fan relay

Sep 26, 2012 | 1998 Ford Mustang

1 Answer

AC and Cooling Fans Not Working


Try installing a jumper across the N/O terminal at the relay socket. Temp sensor in the radiator or in the thermostat housing supplies the signal for the relay the other relay signal is supplied by A/C in on position. both fans will run continuous with A/C on. One fan runs intermittent relative to water temp. Be careful not to blow a head gasket. If you leave the jumpers in place, the fans will stop when the ignition is turned off, save the engine until you isolate the relay signal problem. then simply remove jumpers and reinstall the relays

Feb 28, 2017 | 1989 Toyota Camry

1 Answer

Where are the cooling fan relays located?


This may not help, but it looks like two fan relays are in a box on the passenger side of the engine compartment. The info should be in the owners manual.
Let me know if you don't find it.

Aug 17, 2012 | Cars & Trucks

1 Answer

Temp sending unit location


1 in the intake man. 1 in the cyl. head

Jun 15, 2012 | Cars & Trucks

2 Answers

Can't find relay for radiator cooling fan on 2005 GMC sierra


relays are located left end of the instrument panel.look inside owners manual in glove compartment, it has all fuses and relays locations.

Feb 08, 2012 | 2005 GMC Sierra

2 Answers

I have a 1999 Alero 3.4 V6 the cooling fans won't run. I checked the fans they both work if I unplug the harness for the temp sensor,the relays and fuses are fine,I replaced the coolant temp sensor and...


CHECK MODE RELAY IF BOTH RELAYS GOOD YOU CAN CHECK RELAY BY REMOVING IT FROM FUSE BOX HOOK RELAY TERMINAL 85 TO BATTERY POSITIVE AND GROUND TERMINAL 86 IF CLICKS RELAY GOOD. IF RELAY GETTING POWER GOOD AND THE 30 AMP COOLING FAN FUSE OKAY.EITHER THERE IS A SHORT IN COOLING FAN WIRING OR THE PCM HAS FAILED.THE PCM HAS LOST OR COMMAND RUN CIRCUIT IN PCM SHORTED OUT DUE TO PCM FAILURE.LET DEALERSHIP OR GARAGE USE DIAGNOSTIC EQUIPMENT TO ACTIVATE THE PCM SEE IF IT HAS FAILED.DONT SPEND MONEY ON NEW PCM COULD BE SHORT IN THE WIRING CIRCUIT

Sep 06, 2011 | 1999 Oldsmobile Alero

1 Answer

Battery on a 2005 Mustang went dead. Had a Jump to get the car started. Drove & speedometer & odometer worked fine. However, I had Triple AAA install a new battery & now they don't work. ...


Did AAA clean the battery cable connections when they installed your battery? Did you check the fuse for the insrument panel?

It could be just bad timing or a coincidense but I am more likely to think things are connected. If your gauges worked after jump starting your car, but not after AAA changed the battery, something changed or was left disconnected.

Jul 03, 2011 | 2005 Ford Mustang

1 Answer

My 2005 mustang engine water is overflowing and boiling I've changed the termosthat and cooling sensor as well as the radiator is not clogged up. The fan doesn't kick in unless I turn the ac on any...


the fan not coming on unless you turn the a/c on is a clue.this tells you the fan is working but the coolant sensor for the fan operation may not have been the one you changed(as there is one for the dash gage/light and one for the computer to turn on the fan).also the fan relay may be the problem not turning the fan on without the a/c on.

Jun 21, 2011 | 2005 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

585 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...