Question about Plymouth Acclaim

Open Question

How do i replace a 1992 plymouth acclaim rear wheel bearings

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

  • 7 Answers

SOURCE: plymouth acclaim ignition repair

the ignition cylinder will run you about 20$ and it is fairly easy to change you can change it yourself buy the chilton book (it will help later) and it will be cheaper than paying for labor although the entire replacement will take less than 30 min

Posted on Feb 19, 2009

  • 4369 Answers

SOURCE: rear wheel bearing

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Posted on Apr 10, 2009

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

  • 101 Answers

SOURCE: how do i replace the rear wheel bearing on my peugeot 206

wheel off remove the tin cap in the centure of the hub undo the big nut put the wheel back on with just 2 bolts finger tight so you can pull the hub off.once the hub is off take the 2 wheel bolts back out.now look in side the hub were the big nut was and you will see a sir clip take that out.then use a socket and a bench vice to press the old bearing out.use the socket and bench vice to put the new bearing back in.

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 Plymouth Acclaim bings when car first excelerates


I would have the drive train checked over and maybe the suspension too

Jul 19, 2015 | 1992 Plymouth Acclaim

2 Answers

Do you have photos of how to replace rear wheel bearings on 94 Plymouth acclaim


no we do not but a good repair manual will have all that information in it

Jun 15, 2015 | 1994 Plymouth Acclaim

1 Answer

Sir...i need a wiring diagram for the rear defroster circuit on a 1992 plymouth acclaim


Most Auto parts stores sell books that have the diagrams for the entire car.

Jul 04, 2014 | 1992 Plymouth Acclaim

1 Answer

Diagram for 92 acclaim serpentine belt


For the 1992 Plymouth Acclaim:
Click on the following free, direct Link. It has several Seprentine Belt Diagrams, including one to match your specific 1992 Plymouth Acclaim with the unspecified Engine: 2.5L SOHC In-Line 4-Cylinder or 3.0L SOHC V6; and the unspecified Engine Options (AC/No AC ect.)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1992/make/plymouth/model/acclaim/1992_plymouth_acclaim_drive_belt_routing_diagram.htm

Apr 17, 2010 | 1992 Plymouth Acclaim

1 Answer

I get a vibration as im driving possible from the rear wheel


a) Wheel Balance.
b) Wheel Alignment
c) Wheel Bearing.
My best guess is a wheel bearing needing replacement. If there is only noise, then MAYBE repacking of bearings. However with vibrations, the wheel bearing(s) need to be replaced. Make sure you replace both the bearing and races as a set.
Let me know if this helped or if you need additional help.

Dec 09, 2009 | 1992 Plymouth Acclaim

1 Answer

Replace front wheel bearings


Have to buy bearing & hub assembly as one, about $90 each wheel.

Aug 10, 2009 | 1994 Plymouth Acclaim

1 Answer

Replacing front wheel bearing


you need to remove cv axle,makes things easy,i believe the wheel bearing is a "cassette" style.three or for bolts on the backside of knuckle holds bearing assembly in

Feb 11, 2009 | 1989 Plymouth Acclaim

1 Answer

Plymouth acclaim ignition repair


the ignition cylinder will run you about 20$ and it is fairly easy to change you can change it yourself buy the chilton book (it will help later) and it will be cheaper than paying for labor although the entire replacement will take less than 30 min

Nov 26, 2008 | 1992 Plymouth Acclaim

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...