Question about Cars & Trucks
Howdo i change the pads
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: front brake pads
Just did this tonight... 7/21/08
You need a torx head T-55 Star Socket to remove the caliper bolt(s) and a large 3/4 in preferably with a 1/2 dr and large breaker bar or torque wrench with a 1/2 in dr. to remove the knuckle bolts. I should've taken pictures, but I did not. After studying this exact issue for an hour or so, I finally got everything to click. Steps as I proceeded. Loosen the top caliper nut using the T-55 torx bit, this will take some doing, if possible, use a breaker bar or something comparable, I used a standard 3/8 in. socket wrench and about a foot long hollow metal tube on the end as the breaker and after some muscle work (ouch!!) got it loose. Now there are 2 bolts that hold the caliper in place that need to come out. I used a 3/4 in socket on a 1/2 breaker bar to get these to break. I don't have the exact torque specs to put these back on, but I went about 40lbs on the knuckle bolts and closer to 80lbs on the caliper torx head screw. Once you have the caliper torx head bolt loose and the other 2 nuts off, you can rotate the caliper. Using a C-Clamp, compress the caliper so that it is completely compressed. Now, remove the torx head bolt and the pad assembly will swing out, at this point, you can remove the old pads and clips if you are replacing them as well. Reverse the order for installation using Lock-tite and the caliper grease you get from the parts store. I hope I don't have to mention removing the tires, using jack stands and being completely safe under there. Good Luck. The first side took me about 3 hours considering time and studying, the second side took about half an hour after already knowing what to do.. It gets easier each time you do it.
So far, I have replaced 2 fuel pumps (at home) first one took about 7 hours, second time around, only took about 2 hours. Front and Rear brake jobs. numerous small items, now I'm looking at a blinker switch (problem with left turn signal... rapid click, no light).. Also, the dash panel either needs repaired or replaced as the fuel gage is constantly up and down. If you or someone else has a suggestion here, I would appreciate it.
Thanks and remember... Practice Safe "Do it yourself"..!
Posted on Jul 22, 2008
SOURCE: Replace front brake pads
1. Loosen lugs to wheel with wheel on the ground. Remove AFTER jacking the wheel into the air.
2. 2 bolts hold brake caliper to the suspension. Located on the inboard side of caliper. Usually is a regular hex bolt or an allen head. You may need to persuade them loose at first with a hammer or extra leverage.
3. caliper can be lifted off rotor exposing the pads. Be sure to note how the pads look in place so you can replace the new ones in the correct spot.
4. Depress the caliper piston completely back into cylinder with large channel lock pliers. be careful not to scar in any way.
4. put small amount of lube grease on bolt when reinstalling.
Good luck.. say a prayer and go for it.
Posted on May 09, 2009
SOURCE: how do I change front brake pads
You will first need to have a car jack, proceed to jack up the front side of the car you want to work on. Make sure you place the jack on the proper location, refer to instruction in manual. Take off your tire, now the whole brake assembly is visible, there will be two bolts on back of the brake unit. One at the top and one at the bottom. Unscrew both of these and proceed to slide the used pads and the unit you've just unscrewed. Make sure you clean off all dirt, rust and break pad rosedew. Now you'll need a C-clamp, The piece with the rubber protector on it needs to be compressed back into its compartment with the use of your C-clamp. Now that the unit is clean and the compressor is back in the chamber it's time to replace the small steel break sliders with the new ones provided with your new break set, slide your new breaks into those slots, beside the router. Your almost finished, just slide the break compressor back over the breaks and bolt the unit back on, make sure you tighten the bolts well , as these are your breaks and they will save your life. The only thing to do now is clean your tire inside and out while its off and put it back on your car. Have fun and don't worry it's easy.
Posted on Jan 16, 2010
SOURCE: Change Front Brake pads
(10) Install master cylinder fluid reservoir cap.
Hope this helps...I know it's extremely difficult to find manuals for these cars. These instructions are straight out of the factory service manual.
Posted on Mar 12, 2010
my car was stollen and used in a robbery and high speed chase.the strip was used to flatten the front tires and he still ran 1mile and a half on them flat.but my insurence payed to get it fixed after my 500.00 deduct.when i got it back i have damage to the front finder they didnt fix.and after i traveld 500 miles to come back home i have a bad noise in front when i had the oil changed i had him check it and he said something had gotten into the brake shoe pasanger side and chued it up now im afaried to drive it and dont have the money now to fix it is this maybe from all that went on with it he ran across a yard and colbert i was told that its hard to get stones in the brakes to do that kind of damege.should i go back to insurance co.i had asked them to make sure they checked out good now im in another state
Posted on Mar 15, 2010
Tips for a great answer:
Jan 22, 2016 | Cars & Trucks
May 19, 2013 | 2004 Buick Century
Aug 05, 2011 | Ford F-150 Cars & Trucks
Sep 30, 2010 | Audi A6 Cars & Trucks
Feb 23, 2010 | Daihatsu Rocky Cars & Trucks
Nov 27, 2009 | 2002 Kia Sportage
Oct 05, 2009 | 2001 Hyundai Accent
Aug 16, 2009 | 1992 Daihatsu Rocky
Apr 23, 2009 | 2001 Nissan Quest
139 people viewed this question
Usually answered in minutes!