Question about GMC Sierra

Open Question

Replace starter on gmc truck 1989 - Sierra GMC Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1118 Answers

SOURCE: Replace starter on 1992 GMC Sierra pickup truck

First thing unhook positive battery cable, unhook main cable on starter selanoid and small wire on selanoid (there may be 2 small wires) There may be a bracket on front of starter that has to be removed, and then the 2 main bolts that hold it to engine block and it should come out.

Posted on Feb 14, 2009

motor1258
  • 6674 Answers

SOURCE: how to replace a brake light switch for a 1989

Look up under dash where brake pedal pivots, you should see a switch that is activated by pedal arm.

Posted on Mar 07, 2009

  • 56 Answers

SOURCE: 1989 GMC Sierra truck doors loose

Hey there.You can purchase a door pin and bushing repair kit to tighten up the hinge area,requires removing the door to replace.If the hinge area is worn to badly,the brass bushings willnot last.Also your window crank handle is held on by a C-clip behind the handle in between the plastic shim and the handle which requires a special tool to remove or a small screwdriver to get the clip off.It is hard to see.The shaft that the handle is on are known to wear also and if thats the case you will need to have the window regulator replaced.Hope this helps.John.

Posted on Mar 10, 2009

  • 1 Answer

SOURCE: terminals on GMC 1989 replacement starter

your new starter should have a S and a R terminal and also a large terminal thats for your main power . funny thing is im having starter problems with same truck man.

Posted on Mar 29, 2009

  • 593 Answers

SOURCE: How to replace the thermostat on a 1989 GMC Sierra

The thermostat is located on top of the engine, under
the upper radiator hose. Put a drain pan under the front of the engine, Loosen the clamp on the hose at
the eng. Twist the hose from side to side to break it
loose.(it may be a little stuck) Slowly remove the hose and let drain. Remove the 2 bolts that hold the
thermostat housing,( 1/2" socket or wrench)remove housing. Next, remove thermostat (it may be in the housing) and scrape off the old gasket and sealant.
On the inside of the housing you will see a groove
around the hose inlet, put a little sealant in the groove
to help hold the therm. in place. Install the thermostat
into the groove, with the copper sensor facing out.
Put a little sealant around the mounting surface on
the housing and put the gasket in place, let the
sealant set up for about 15 minutes. Replace the
housing making sure the thermostat stays in the
groove, if it gets dislodged and pinched between the
housing and block, you may break the housing when
you tighten it down. Replace the hose fill with coolant. Before you replace the housing fill the block
with coolant, this will help purge the air from the system. I should have said that a paragraph ago.
I hope this helps you.

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 suburban front bumper


Sara, 1989 GMC Suburban front bumper removal. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Install Replace Bent Rusted Front Bumper 1989 99 Chevy GMC Pickup...
Grille Replacement 88 98 Chevy trucks
1989 Chevrolet R1500 Suburban Parts NationalGMParts com

Jul 10, 2016 | 1989 GMC Suburban

1 Answer

My 1989 gmc sefari wont start.. i started it this morning and the lights briefly dimmed, i drove my mother to a dr. Appoinmet & when i went out to start the van it would not start.. the radio,heat and...


Bad starter solenoid most likely. If you can even see the starter (which I doubt) might try tapping it hard with a broom handle which could jiggle the parts in the solenoid and make it start. Otherwise, tow it and replace the starter and solenoid as one part.

Feb 26, 2015 | 1989 GMC Safari

1 Answer

I cant get my starter to work and i was wondering if i need shims for my new starter on my 89 gmc 1500


most times if you are installing a remanufactured
starter the proper shims would come in the box.
it's hard to tell what is going on from your discription.starter does not start ? does it make any noises, clicking sounds or anything ?

Mar 29, 2009 | 1989 GMC C1500

1 Answer

Terminals on GMC 1989 replacement starter


your new starter should have a S and a R terminal and also a large terminal thats for your main power . funny thing is im having starter problems with same truck man.

Mar 06, 2009 | 1989 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...