Question about 2001 Chevrolet Suburban

1 Answer

I've had the #2 knock sensor errror 4 times i took the 2001 suburban to the chevy dealer to have both sensors and the harness replaced. they say the fuel tank pressure sensor is showing low valt

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sounds like the Knock sensor bolt has been over torqued.

Posted on Feb 14, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

04 Chevy avalanche knock sensors location


Nathan, 2 Knock's are located under intake manifold.
Check the attached links,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How To Install Replace Engine Knock Sensor 2000 06 5 3L Silverado Sierra...

Knock sensor 5 3 4 8 6 0 replacement

05 Chevy Avalanche Knock Sensors

4 8 5 3 6 0 knock sensor replacement GM



Mar 06, 2016 | Cars & Trucks

1 Answer

2005 suburban 5.3 engine where are knock sensors located and how do you replace them


two knock sensors.under phlemm assy. replace cover gasket, two sensors and wire harness.

Jan 27, 2013 | 2005 Chevrolet Suburban

1 Answer

How do you change a knock sensors on my 2001 gmc 1500hd


Changing knock sensors on 2001 GMC 1500hd
1. Remove the intake manifold.
2. There are 2 sensors located on a plate under the intake manifold. These are the knock sensors.
3. Remove the wiring harness assembly from the knock sensor.
4. Install the new rear bank knock sensor and tighten to 15 lb ft.

If you find that this is information was helpfulto you, please rate me and leave a comment as this will encourage me to do morefree work for you and others. And please let me know if there's anything else Icould help you with. Without any inputswe cannot proceed assisting... Thank you for using FIXYA! Best regards,
Junior

Sep 14, 2011 | 2001 GMC Sierra 1500HD

1 Answer

How to tell which or if either knock sensor is bad on a 2005 Chevy suburban 5.3. I have a light on that two mechanics read and both said it's the knock sensor low circuit #2


usually the sensors (2) are good but the harness goes bad and there is corrosion at the knock sensor connection. The intake manifold need to be removed and the harness replaced. KNOCK SENSOR 2 IS THE REAR.

Sep 12, 2011 | 2005 Chevrolet Suburban

1 Answer

I have an engine code PO332 knock sensor 2 circuit low imput bank 2 what is this problem .the car is a 2001 gmc yukon xl .


The most likely cause of your code is a bad rear knock sensor. You should check the knock sensor wiring harness for corrosion. But if that checks out the sensor will have to be replaced. The knock sensor is under the intake manifold, although it's not too difficult to remove. Both knock sensors should be replaced along with the wiring harness, just because of labor involved in gaining access to the sensors. You could try clearing the code, it may stay off for a long time.

May 23, 2010 | 2001 GMC Yukon XL

4 Answers

Where is knock sensor located on 2001 silverado 6000 engine


Under the intake manifold. Make sure you get the harness for the knock sensors. and clean out all of the rust and junk you're going to find donw in the holes before and after you replace the sensors.

Nov 01, 2009 | 2005 Chevrolet Silverado

1 Answer

Where is the knock sensor for 2001 chevy suburban located


this is located on the bottom of the block just above the oil kind of mid center of the block most of the time of pass side

Sep 26, 2009 | 2001 Chevrolet Suburban

1 Answer

Knock sensor


check out you tube, replacing knock sensor

Sep 05, 2009 | 2001 Chevrolet Silverado

1 Answer

Knock sensor location


HI, click the link below to be directed to a full diagram that will show you the actual location of the sensor. 718 will be the actual sensor to extract and 739 is the mounting screw for the KS.

KNOCK SENSOR DIAGRAM

Jul 22, 2009 | 2001 Chevrolet Silverado

1 Answer

2001 chevrolet suburban knock sensor


you have 2 of them on that vehicle and both of them are located under the intake manifold.

Sep 12, 2008 | 2001 Chevrolet Suburban

Not finding what you are looking for?
2001 Chevrolet Suburban Logo

605 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...