Question about 2000 Oldsmobile Intrigue

Open Question

Where is the reset button on fuel pump for 2000 olds bravada

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

garyq1970
  • 73 Answers

SOURCE: fuel pump 1998 olds bravada

  1. Properly drain the fuel tank, then disconnect the negative battery cable.
  2. If not done already, raise and support the rear of the truck safely using jackstands.
  3. If equipped on late-model vehicles, loosen and remove the tank plastic shield.
  4. Loosen the retaining clamp and disconnect the tank filler hose from the tank neck.
If fuel and vapor hoses or pump/sending unit wiring can be accessed at this time, they may be tagged and disconnected. If not, wait for the retaining straps to be loosened and lower the tank slightly for access.
  1. Tag and disconnect and accessible wiring or hoses from the top of the fuel tank.
  2. Have and assistant support the fuel tank, then remove the fuel tank-to-vehicle straps and, if equipped, the isolation strips. If no assistant is available, position a floor jack to support the tank while the straps are removed.
  3. Lower the tank slightly, then remove the sending unit or sending unit/pump wires, hoses and ground strap. Be sure to label all connections to ease installation.
  4. Carefully lower the fuel tank from the vehicle and store in a safe place.
To install:
  1. Raise the tank partially into position in the vehicle. If you are working without an assistant, you may wish to loosely install one of the retaining straps and use a floor jack to support the tank at an angle so there is access to the sending unit or sending unit/pump assembly (as applicable).
  2. Connect the fuel/vapor hoses and wiring to the top of the fuel tank, as tagged during removal.
  3. Carefully raise the fuel tank so it is fully into position and loosely secure the retaining straps. Make sure the wires and hoses are not pinched or damaged when raising the tank. Also, be sure that the isolation strips (if used) are positioned between the retaining straps and the fuel tank.
  4. It may be easier to connect the fuel filler hose to the tank neck at this time. If desired, connect the hose and secure the clamp.
  5. Tighten the fuel tank retaining strap fasteners to specification. Tighten the strap nuts to 33 ft. lbs. (45 Nm).
  6. If not done earlier, connect the tank filler hose to the tank neck and secure using the clamp.
  7. If equipped, install and secure the tank plastic shield.
  8. Remove the jackstands and carefully lower the rear of the truck.
  9. Refill the fuel tank and install the filler cap, then check for leaks.
  10. Connect the negative battery cable.
Equipped With Shield Package
  1. Properly drain the fuel tank, then disconnect the negative battery cable.
  2. Raise and support the rear of the truck safely using jackstands.
  3. Remove the shield forward support and bracket.
  4. While supporting the shield and tank assembly with the help of both an assistant and a floor jack, remove the remaining bolts holding the assembly to the frame, then lower it sufficiently for access to the hoses and wires.
  5. Tag and disengage the hoses and wires from the sending unit assembly.
  6. Carefully lower the fuel tank and shield from the vehicle, then if necessary for service or replacement, separate the tank from the shield.
To install:
  1. If separated, install the tank to the shield.
  2. Carefully raise the tank and shield assembly partially into position with the help of an assistant and a floor jack.
  3. Connect the wiring and hoses to the sending unit assembly, as tagged during removal.
  4. Raise the tank and shield assembly fully into position, then secure to the frame using the lower retaining bolts.
  5. Install the shield forward support bracket.
  6. Remove the jackstands and carefully lower the rear of the truck.
  7. Refill the fuel tank and install the filler cap, then check for leaks.
  8. Connect the negative battery cable.
  any question I can send some diagrams

Posted on Nov 12, 2008

louislevel_2
  • 374 Answers

SOURCE: 2000 Bravada won't start, turns over, no gas to injectors.

hi! there
car can't start,there are several factor we can consider in this
case to asssure that car will run normally.have all this check
this mostly parts of your ignition system,checka faulty coil this
give your spark plug sufficient current to burn and produce
compression.your conderser must be check also if this was
busted,your contact point must be clean,the high tension wire
should be check also replace faulty wirng,check particular
timing,and replace busted spark plug.

Posted on Apr 17, 2009

  • 77 Answers

SOURCE: fuel pressure regulator

Regulator is under plastic intake plenum.

Posted on May 04, 2009

  • 1 Answer

SOURCE: need diagram for fuel pump replacement for 1994

problem solved

Posted on Jul 10, 2009

  • 41 Answers

SOURCE: 99 olds bravada. just replaced fuel pump 2 weeks

Aftermarket fuel pump failure? Try "thepartsladi" store on eBay for low price GM OEM parts. Could also be wiring harness to fuel pump.

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Old fuel pump had three prong plug. new one has four prongs. what do i do with the fourth wire?


How to Install the Fuel Pump E3992M in 1998-2005 ...

? 4:55
www.youtube.com/watch?v=sRq2ohp8A7o
Apr 20, 2012 - Uploaded by Airtex Pumps 2001-98 OLDSMOBILE BRAVADA 262 (4.3L) ... is committed to providing the most up-to-date, in-depth fuel pump replacementinformation that ...

Oct 10, 2015 | 2000 Oldsmobile Bravada

1 Answer

2000 olds bravada.fuel pump runs,new fuel filter,but no gas to throtte body


The throttle body doesn't get any fuel

It only lets air in

The fuel pressure regulator is under the upper intake,
as are the injector poppet valves

Go to You Tube Video & watch Wayne at Real Fixes
Real Fast to see the problem

Mar 03, 2013 | 2000 Oldsmobile Bravada

1 Answer

Fuel Pump 2000 Bravada changed but still not working... help!!!!!!


You check the relay?Make a tool out of the relay take the relay apart collapse it.to make full contact and stick it back in,key does the fuel pump come on?If yes keep it like this for 15 minutes if the vehicle stall,the problem is not the fuel pump, The ECM must see a RPM of 250 or more in order to turn the fuel pump on. If it doesnt see a RPM of a 250 it doesnt even know its running.Okay back to the tool you made,This only trouble shoot the fuel pump system

Mar 12, 2012 | 2000 Oldsmobile Bravada

1 Answer

Low power and missfire, have replaced bad distributor and rotor. 2000 Oldsmobile Bravada AWD. Where are the fuel pump and filter located?


I have replaced Distributor cap, rotor, wires, and spark plugs in my 2000 Oldsmobile Bravada AWD smart track. To replace one spark plug I had to collapse the steering column, but everything went O.K. Did you marked the wires?. Did you reconnect them in the firing order?
The fuel pump is located In the fuel tank. Remove the fuel tank and take the fuel pump out from the top. This is part cost $300 and need some skills to be replaced.
The fuel filter it is directly in front of the fuel tank. Another one is incorporated with the fuel pump.

Sep 10, 2010 | 2000 Oldsmobile Bravada

1 Answer

I am having problems starting my 2000 Olds Bravada in cold weather, even only 11-20 degrees. I have to pump the gas pedal in order for the vehicle to start, after a few tries. I can hear the pump working...


The pump is supposed to stop when the fuel rail has enough pressure so the 5 sec. thing is normal.Sounds like you need a throttle position senser replacement.

Dec 14, 2009 | 2000 Oldsmobile Bravada

1 Answer

Turns over but want start 2000 olds bravada


Probably bad fuel pump, common problem. Have someone check the fuel pressure at service port close to firewall. Should be 50-60 psi. OEM part is recommended, try "thepartsladi" store on eBay.

Nov 17, 2009 | 2000 Oldsmobile Bravada

1 Answer

99 olds bravada. just replaced fuel pump 2 weeks


Aftermarket fuel pump failure? Try "thepartsladi" store on eBay for low price GM OEM parts. Could also be wiring harness to fuel pump.

Nov 12, 2009 | 1999 Oldsmobile Bravada

1 Answer

94 olds bravda no fuel pump not woking.


take rubber hammer tap on fuel tank after turning key on to see if it runs, if it does replace it. check fuses under hood and under dash

Nov 28, 2008 | 1994 Oldsmobile Bravada

Not finding what you are looking for?
2000 Oldsmobile Intrigue Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...