Question about 2006 Chrysler 300

Open Question

How to replace egr valve on a chrysler 300 2006

Replace egr valve

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Engine Light On - 2006 Chrysler 300 3.5 engine

I have a 2005 Chrysler 300. The engine light comes on from time to time -- sometimes it will stay on for a week or so and then go off for at most a day or two. I had the code read yesterday and the feedback was "EGR pressure flow is low." My car has about 65K miles. Is this a typical problem with this car? I was told replacing the EGR valve would fix the problem. How easy is it to replace an EGR valve on this vehicle? Once replaced, do I need to reset the computer --- if so how do I do this? If it is easy to fix, could you please provide step by step directions and show me location of the part in question that needs replaced?

Posted on Apr 10, 2009

  • 1 Answer

SOURCE: Code P0406

Where is the egr valve on my crystler 300?

Posted on Aug 17, 2009

  • 47 Answers

SOURCE: WHERE IS EGR VALVE LOCATED IN 2006 CHRYSLER 300

91ebc6a.jpg

#2 points to the EGR Valve. If you need instruction on how to get to it, let me know.


Posted on Mar 12, 2010

  • 47 Answers

SOURCE: replacing brake light above trunk on 2006 chrysler

This is quite a process....

Removal
1) Disconnect and isolate the negative battery cable.
2) Remove the rear shelf trim panel.

3ca61c4.jpg
3) Disconnect the CHMSL electrical connector (1).

7bde5c5.jpg

4) Remove the two mounting fasteners (3) to the CHMSL (2).

6793725.jpg

Installation is opposite of removal.

Rear shelf trim panel

Removal

1) Disconnect and isolate the battery negative cable.
2) Remover the right and left lower and upper C-pillar trim.
3) Remove the nut that secures the center rear seat belt lower anchor to the stud on the floor panel and feed the seat belt webbing back through the opening in the top of the rear shelf panel trim (2) to the retractor.
4) Remove the push-pin fastener (1) that secures the trim (2) to the rear shelf panel.
5) Slide the trim forward to disengage the S-clip that secures the underside of the trim to the to the center of the shelf panel.
6) Remove the trim from the rear shelf panel.

24614b2.jpg

Installation

1) Position the trim (2) onto the rear shelf panel(3).
2) Slide the rear edge of the trim rearward to engage the lens bezel of the center high-mounted stop lamp and far enough to engage the S-clip that secures the underside of the trim to the center of the shelf panel.
3) Install the push-pin fastener (1) that secures the trim to the rear shelf panel.
4) Pull the center rear seat belt lower anchor and belt webbing from the retractor through the opening the the top of the rear shelf panel trim and back down to the stud on the floor panel.
5) Install and tighten the nut that secures the seat belt lower anchor to the stud on the floor panel. Tighten the nut to 34 N m (25 ft. lbs.).
6) Reinstall the right and left upper and lower C-pillar trim.
7) Connect the battery negative cable.

841a5de.jpg

C-pillar trim removal

1a140ec.jpg

5ad047d.jpg

b674bd4.jpg
cf360b2.jpg

cd4ac09.jpg
2e5b4da.jpg

Seat removal

d276bae.jpg
60b3895.jpg

469e099.jpg

087d2a6.jpg

3ad2dc9.jpg


a09baad.jpg
4981771.jpg


Hope this all gets it done for you........

Posted on Mar 12, 2010

  • 565 Answers

SOURCE: Where is the egr valve on a 2006 Chrysler Town

you need to remove the drive belt and alternator to access the egr valve. when replacing the torque on the bolts is 23 foot pounds onetufshoppe_82.gif

Posted on Jan 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 1997 chrysler town and country idles high?


Check the iac idle air control valve or the egr valve which doesnt always need replacing just a simple carb cleaning. If you clean the egr valve replace the o2s it is surely next to go. There can be 2 one on the manifold amd n the other by the cat.

Jul 31, 2014 | 1997 Chrysler Town & Country

1 Answer

Is it a hard job to replace the egr vavle on a 2005 chrysler 300 3.5 engine


the egr valve can be changed from below but the left bolt must be done blindly by feel, (use a small mirror,) undue the 2 bolts and pull it out from the intake, careful to make sure the gasket on the end of the tube comes with it;
the 2 bolts that hold the egr on also has a metal gasket;
the hardest thing is to disconnect the electrical plug from below that connects the egr valve, - do not do this if you have no mech experience;

Mar 26, 2012 | 2005 Chrysler 300

1 Answer

How much should it cost to replace a bad egr valve for a 2005 chrysler 300c


An EGR valve is simple enough to replace. The part alone costs roughly $90.
It is located at the back of the engine.
If you take a look, there will be a Iron rod going from the back of your intake manifold ... downwards ... its going to the EGR Valve.

Cheers,

Aug 24, 2010 | 2005 Chrysler 300

1 Answer

How do you replace the egr valve on a 300


Heat up the exhaust pipe to egr with torch and spray with knockitloose or wd40 when not hot. Then remove that pipe. Then remove vacuum hose and the 2 bolts that hold it on.

Mar 31, 2010 | 2005 Chrysler 300

1 Answer

How do you replace the egr valve in a 1997 chrysler concorde lx


Chrysler Concorde 1993-1997 3.5L MFI 6cyl
Exhaust Gas Recirculation System
Operation

This system reduces the amount of oxides of nitrogen (NO x ) in the exhaust by allowing a predetermined amount of exhaust gases to recirculate and dilute the incoming fuel/air mixture. The diluted air/fuel mixture reduces peak flame temperature during combustion, which in turn inhibits the production of Nitrogen oxides. The principal components of the system are:
- EGR tube (connects a passage in the intake manifold to the exhaust manifold)
- EGR valve
- Electronic EGR Transducer
- Vacuum hoses


Component and System Testing
  1. Check the condition of all of the EGR system hoses and tubes for leaks, hardening or kinks on the rubber hoses. Repair and correct these conditions before proceeding any testing.
  2. Be sure that the hoses at both of the EGR valve and EGR valve control are connected to the proper fittings.
  3. Be sure the electrical connector is firmly attached at the valve control.
  4. To check the EGR system operation, connect the DRB III scan tool or equivalent to the 16-way data link connector. The data link connector is located on the lower edge of the instrument panel near the steering column. Follow the scan tool instructions.
  5. After checking the system with the DRB III scan tool, proceed to the EGR valve leak and control tests, then repair as necessary.

Removal & Installation
EGR Valve and Transducer

395f8b9.jpg

EGR valve and transducer assembly-3.5 engine



025dc6c.jpg

The EGR valve attaches to the back of the cylinder head-3.5L engine


bc80254.jpg

Loosen, but do not remove, the EGR tube to intake manifold screws

The EGR valve attaches to the rear of the right cylinder head.
  1. Remove the vacuum tube from the electric EGR transducer solenoid. Inspect the vacuum lines for cracking, poor seal due to hardness, or other problems. Replace with new hoses if necessary.
  2. Remove the electrical connector from the solenoid.
  3. Slide the transducer up and out of the mounting bracket.
  4. Loosen, but do not remove, the EGR tube to the intake manifold screws.
  5. Remove the EGR tube lower screws at the valve.
  6. Remove the EGR valve and transducer.
  7. Clean both gasket surfaces and check for any signs of leakage or cracks. Replace the components if any such damage is found or if the valve fails the tests.

To install:
  1. Loosely install the EGR valve and a new gasket onto the cylinder head.
  2. Using a new gasket, attach the EGR tube to the valve and tighten the screws to 95 inch lbs. (11 Nm).
  3. Tighten the EGR tube to the intake manifold plenum screws to 16 ft. lbs. (22 Nm).
  4. Tighten the EGR valve to the cylinder head screws to 16 ft. lbs. (22 Nm).
  5. Reconnect the transducer solenoid to the vacuum fitting on the manifold.
  6. Slide the transducer into the bracket.
  7. Reconnect the vacuum lines and electrical wires to the EGR transducer.
continue...

Sep 04, 2009 | 1997 Chrysler Concorde

1 Answer

Describe your 2006 Chrysler Town & Country Problem p0404 engine code


P0404 IS EGR POSITION SENSOR PERFORMANCE..YOU NEED A NEW EGR VALVE..RECOMMEND DISCONNECTING BATTERY WHILE REPLACING EGR VALVE..SOMETIMES CODE WILL NOT GO AWAY EVEN AFTER REPLACING VALVE AND CLEARING CODE WITH SCANNER..VALVE IS LOCATED ABOVE ALTERNATOR ON END OF CYLINDER HEAD..THE BOTTOM BOLT CAN BE TRICKY TO REMOVE AND HAVE HAD TO REMOVE ALTERNATOR TO GET BOLT OUT..YOU WILL NEED A NEW GASKET FOR TUBE AS WELL..ABOUT 120 BUCKS FROM DEALER(CAN)

Jul 25, 2009 | 2006 Chrysler Town & Country

2 Answers

2005 Chrysler T&C EGR valve solenoid problem


YOU NEED TO DISCONNECT THE BATTERY FOR 5-10 MINUTES FOR FAULTS TO CLEAR COMPLETELY..HAVE SEEN THIS PROBLEM BEFORE AFTER REPLACING AN EGR VALVE..IT WAS A TECH TIP FROM CHRYSLER ENGINEERING..THE EGR VALVE WAS THE PROBLEM,BUT THE PCM WOULD NOT LET THE CODES GO EVEN AFTER CLEARING THEM WITH SCAN TOOL..ALSO CHECK CONNECTIONS AT EGR CONNECTOR FOR SPREAD PINS

Jul 09, 2009 | 2006 Chrysler Town & Country

1 Answer

Check engine light came on and the error code is 040.4 what is it and can i drive it?


this is an egr valve trouble code..you need a new egr valve..make sure you disconnect battery when you replace it..sometimes fault will come back even though replaced valve

May 09, 2009 | 2005 Chrysler Town & Country

2 Answers

Code P0406


Where is the egr valve on my crystler 300?

Apr 10, 2009 | 2005 Chrysler 300

Not finding what you are looking for?
2006 Chrysler 300 Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...