Question about 2001 GMC Yukon XL

1 Answer

Brake problem i have a 2001 gmc yukon xl and my brake pedal is almost down to the floor when i brake to stop. I've bleed the system, replaced brake pads every year, no leaks on the lines or any brake system parts but i've noticed the brake pads hardly wear out every time i replace the pads. what else can i do to fix it? please help

Posted by on

  • Anonymous Mar 17, 2014

    WITH NEW BRAKE PADS PEDAL GOES TO FLOOR ON FIRST PUSH BUT STAYS UP NORMAL ON SECOND TRY. HAVE BLEED BRAKES. WHAT ELES WILL CAUSE THIS

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 314 Answers

Hi Tora, Go to the back brakes. This is where the prob could be. But with you bleeding the brakes, the peddle has went beyond its normal travel causing the rubbers in the master cylinder to get messed up. Happens too often! Replace the master cylinder 'after' you had a good look at the back! Frankster016

Posted on Oct 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced ABS modulator valve, unable to bleed brakes. What can I do?


Need special tool (electronic) But before that read this:http://www.stoptech.com/technical-support/technical-white-papers/bleeding-abs-brake-systems.

Oct 24, 2013 | 2001 GMC Yukon XL

1 Answer

Breaks going straight to the floor replaced the booster, stil not working


If your brakes are all good you may need to bleed your master cylinder, I had that happen once.You have to remove the lines and run lines or hoses back in to the cavities and run it through until it is solid. Make sure your back brakes are adjusted up too.

Sep 02, 2012 | 2005 GMC Yukon Xl Denali

1 Answer

Two weeks ago I found the brake pedal suddenly did not keep the normal height and went down to the bottom. It gets back to normal height right now but if I press down the pedal softly it still travels...


check for fluid leaking at the wheels and at the base of the master cylinder. Check fluid level in the reservoir. If any leaks, replace leaking component and bleed system. If no leaks and reservoir is not low, replace master cylinder. If you don't have experience with these repairs, get some help.

Sep 03, 2010 | 2001 GMC Yukon Denali

1 Answer

How do you reset oilchange light on a 2001 yukon xl


turn key to on position, pump gas pedal to floor 5 times and turn off key. start vehilce. Change oil light should flash for 7 seconds and then go out.

May 15, 2010 | 2001 GMC Yukon XL

1 Answer

Brakes


Either you didn't bled it thoroughly or the line isn't correctly installed and it leaks. Check everything again and do a proper bleed this time.

Apr 26, 2010 | 1996 GMC Yukon

1 Answer

While in stop and go traffic my brake pedal went


check the brake fluid level, if its low, there may be a leak, if the level is good, the master cylinder is bad.

Oct 15, 2009 | 2001 GMC Yukon

2 Answers

Excessive brake pedal travel brake pedal goes almost to the floor before stopping, tried bleeding brakes at the callipers with no difference.


Check the rear brakes are not leaking, or have air in the fluid feed line.
If above OK, it's probably caused by a faulty master cylinder.
(To check :- Slacken off the master cyl feed to the front (then rear) brakes, and observe if any fluid is being delivered - if not it is definitely a master cyl problem).

Aug 10, 2009 | 2001 GMC Yukon Denali

1 Answer

Need brake help with 2001 Silverado 2500 HD. I replaced both rear calipers and master cylinder cannot seem to bleed the brake system. The pedal will not build up any pressure. Is there something I need to...


There is nothing special that you need to do. You need to make sure that you bleed the brake system starting at the master cylinder FIRST. You also want to make sure that you do not have any more leaks or open lines. Do not turn the car on until the brakes are bled or the air will go into the other circuits. The other thing to look out for is bad brake pads, If these are worn they can cause kind of a spongy pedal.

Jun 10, 2009 | 2002 GMC Yukon XL

Not finding what you are looking for?
2001 GMC Yukon XL Logo

441 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...