Question about 2001 Fiat Punto

Open Question

What are the tappet clearances for punto 1.9 jtd

What are the inlet and exhaust valve clearances

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
iambanshee74
  • 3489 Answers

SOURCE: i am owning an palio1.9d

I know from experience with Mercedes diesels that correct tappet clearance is critical. As the engine wears you may need to accommodate for wear. I would adjust again closing the gap but, very very little. I would be careful not to overdo. I may be wasting my words but, make sure you are on the heal of the cam when making the measurement. Let me know if you need anything else.

Posted on Aug 14, 2010

Ad
carlon90
  • 183 Answers

SOURCE: what damage will happen if my timtng belt snaps on

Nothing will happen. I have tried the same situation - no problem

Posted on Jan 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

What is the tappet/valve clearance for the Renault scenic 2003?


E7J engine 1600cc when cold- INLET 0.10mm
EXHAUST 0.25

2.0 Ltr engines have valve control solenoid and you would need to get a workshop manual for this procedure

Diesel engines(1.9 F8Q & F9Q) when cold -INLET 0.20
EXHAUST 0.40

Jun 10, 2015 | Renault SCENIC Cars & Trucks

1 Answer

How do I set tappets of a 2.5 diesel turbo mazda


you haven't mentioned if it is a 4 cyl or not. However bring no 1 cylinder up to tdc and watch the tappets of the next cylinder to fire. when that cylinders rockers are in valve overlap situation ( exhaust starting to close and inlet starting to open) then that will be maximum clearance on no 1 cylinder and is when you set the tappets turning the engine until the next cylinder is at TDC watch for the next cylinder again to be in valve overlap and repeat as for no 1 cylinder

Dec 25, 2014 | Mazda Cars & Trucks

1 Answer

Petter engine tappet clearance


.010" hot inlet and .012" exhaust hot. if it is an air cooled engine go up.002" in settings.

Nov 30, 2014 | Cars & Trucks

1 Answer

Please give me the correct tappet clearance of intake and exhaust valve of mitsubishi 4g54 with turbocharger


My initial sweep of the web gives Inlet 0.010 thou, Exhaust 0.008 thou.
You would need to check this because industry norm is to have the greater clearance on the exhaust valve because of the increased heat expansion.

Nov 05, 2013 | 1992 Mitsubishi Pajero

1 Answer

Valve Clearances inlet and exhaust


j24b engine D.O.H.C.
U.S.A?
open hood , look up. see white sticker, see clearances.?
off online F.S.M
Valve clearance specification when cold :
59 to 77deg F or 15 to 25deg C (engine temps)
Intake: 0.0063 to 0.0094 inch (0.16 to 0.24mm)
Exhaust: 0.0123to 0.0153 inch (0.31to 0.39mm)
you must remove the bucket,tappet , to change lash.
MIKE IT (that means a micrometer)
then buy shims or new buckets to fit. (generic answer)
the book says buy correct tappet after measuring, yours.
and it's out of range, and doing the math first.

that is it.

May 05, 2013 | 2010 Suzuki Kizashi

1 Answer

1995 jeep 4.0 valve train clearance


As a rule of thumb most valve clearences are .010" inlet and.012" exhaust ( hot) but I suspect yous will have hydraulic tappets which take up the clearence as soon as the oil pressure comes up

Mar 09, 2013 | Cars & Trucks

1 Answer

In an inline 4 cylinder 8 valve scorpio 2006 crde engine having 1-3-4-2 firing order which valve is first - the outlet or the inlet


from the belt side first valve is inlet second valve is exhaust..bigger valve is inlet small valve is exhaust also you will have a black colour in exhaust valve stems...

Feb 28, 2013 | 2011 Mahindra Scorpio

2 Answers

I have problem with my engine 4K toyota. It heard an engine noise during idling, for my little knowledge in engine repair, can you give me any procedure mannuals in adjusting engine valves for my...


Valve Clearance Valve clearance is there to allow the valves to cool in between combustion events (spark), and to make sure the valve closes properly and contains the combustion explosion. You need to cool the valves a little bit, the exhaust valve moreso than the inlet, as it's what sees the most heat as spent burnt gases go past it into the exhaust port. Run too little clearance and you'll cause the valve to "weld" a little bit to its' seat every time it closes, and then take seat metal off again when it opens. Do this enough times and you burn out the valve seat and need the head reconditioned. However, by running less clearance, the valve stays open for that little but longer, and you get more air in and out of the motor, and make more power. Run too much clearance and your motor just sounds like a diesel and loses power and tappet rattle annoys you while you're driving, so it's better to err on the side of caution.
The stock valve clearance (0.008" inlet / 0.012" exhaust, warm) is pretty good for any of the cams I've listed above, they're well-sized street cams, not really wild top heavy race cams that require super high compression to work, so don't be afraid to close the valves up a bit from the suggestions of the cam grinder, which will usually say between 0.010" and 0.014". There are a few ways to set your valve clearances:
Yellow Book Method This is from the factory 3K/4K/5K engine manual, aka The Yellow Books. It's the quick and lazy method.
Set engine to #1 TDC. Crank pulley timing mark should be on 0, distributor rotor should be pointing towards spark plug 1 or 2. Set tappets (counting from the front) 1, 2, 3 and 5. Rotate engine 360 degrees, crank pulley to 0 again, distributor rotor turned 180 degrees. Set tappets 4, 6, 7 and 8.
Nine Method I've never really gotten into doing this, takes too much time and maths for my liking :P Rotate the engine through its' range of movement, as one valve is "on the rock" of its' max lift, subtract the valve number from 9 and that's the tappet you should be setting. For example, if #8 valve is open, set clearance on valve #1. If valve #7 is open, set clearance on #2. And so on.
Stewart uses this method, and rotates the camshaft through its entire base circle and sets the clearance at the highest point. Which is a pretty good idea, as it compensates for the possibility that the base circle has been ground unevenly, and allows you to run the proper valve clearance that you want to run, instead of something that may be a few thou larger in reality.

Feb 10, 2011 | Toyota Corolla Cars & Trucks

1 Answer

Engine tappet clearances


According to http://freespace.virgin.net/tommy.sandham/databook.htm# Rocker Adjustment, the cold clearance is .008" intake/.018" exhaust in the non-GT 1500cc, and .012" intake/.022 exhaust on the GT. Sweet little car!!!

Mar 01, 2009 | Ford Escort Cars & Trucks

Not finding what you are looking for?
2001 Fiat Punto Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...