Question about Pontiac Cars & Trucks

1 Answer

My keyless entry and remote start quit working

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 17,970 Answers

Hi there:
I suggest to check this information and the right procedure in the Pontiac Owners Manual.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Feb 14, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: nissan murano 2005 sl keyless entry remote programing

Close all vehicle doors, LOCK doors using drivers side switch.

Insert key all the way into the ignition, (do not turn) remove key.

Repeat this step 5 times. (6 total)

Hazards should flash to indicate program mode.

Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

Source

Posted on Aug 06, 2008

  • 60 Answers

SOURCE: keyless entry won't work

Try changing the battery in your remote

Posted on Aug 11, 2008

limotec
  • 33 Answers

SOURCE: Reprogram a keyless entry remote

Hello
this is how to program the remotes/keyless entry

How

  • Obtain all remote transmitters
  • enter the 5 digit permanent code into the keyless entry pad on the drivers door
  • Press the 1-2 switch on the keyless entry pad
  • Within 5 seconds
  • Press any button on the first remote transmitter
  • The doors should open then lock
  • Within 5 seconds
  • press any button on the second & third remote
  • within 5 seconds for each remote
  • to exit programming
  • simultanionusly press 7-8 & 9-0 switchs on the key pad or wait more then 7.5 seconds
NOTE
The 5 digit permanent code is located in one of the following places
  1. On the owners warranty card
  2. On the label on the inside the trunk/ boot
  3. On the owners code card
  4. On the centrel locking control module located in the drivers door
  5. In the PCM ford can get this for about $25.00
I hope this help
Regards Paul
www.limotec.co.uk

Posted on Jan 13, 2009

  • 15 Answers

SOURCE: keyless entry remote quit working. Just purchased

Transmitter Programming Notes Transmitter Programming

  1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
  2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
  3. Repeat step #2 for each additional keyless entry transmitter.
  4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

Posted on Jun 17, 2009

Molson02536
  • 3854 Answers

SOURCE: programming a keyless entry remote

Key Fob Auto Learn
This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming. 

The vehicle must be OFF. 
Place the replacement key fob in the console pocket with the buttons facing forward. 
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds. 

The DIC will display a message: OFF/ACC TO LEARN. 
Press the OFF/ACC portion of the ignition button. 
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time. 
When the counter reaches 0, DIC will display OFF/ACC TO LEARN. 
Repeat steps 5-7 two more times, for a total of 30 minutes. 
The DIC will display a message: OFF/ACC TO LEARN. 
Press the OFF/ACC portion of the ignition button. 
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2. 
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode. 
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode. 
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation. 

Good luck and hope this help's keep me posted, there are 3 other methods and the 5th method is a tech 2 scan tool that the dealer uses but this should work on your year of cadillac. 

Posted on Jul 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The four button remote with keyless entry and remote start on my 2001 buick lesabre has stoped working. The keyless and trunk and horn functions all still work fine just the remote start has quit working. ...


it maybe that the relay in the alarm module for the starting function has stopped working. your best bet would be an alarm shop where they can test the connection for function. have seen this issue several times. Does the engine turn over at all? if it does then the time for cranking may need to be adjusted.

Jan 11, 2014 | Buick Cars & Trucks

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

2007 gmc yukon. Keyless Entry problem. The remote quit working but the gmc place said its not the battery. Help


Disconnect the battery to the car for five mins. Thay should reset the keyless module. I had the same problem

May 20, 2010 | Cars & Trucks

1 Answer

Would anti theft cause car to quit


Sounds like a bad ignition switch have ur body control module checked for codes if u have a B2960 and or B3033 then replace the ignition switch.

SECURITY
If your vehicle has the remote keyless entry system, this feature allows you to select the method used to arm the vehicle's security system. When SECURITY appears on the display, press the reset button to scroll through the available settings:
* RKE (Remote Keyless Entry) (default): The content theft-deterrent system will arm when the lock button on the remote keyless entry transmitter is pressed or when the power door lock switch is pressed.

* PASSIVE: The content theft-deterrent system will arm itself 60 seconds after the ignition has been turned off and all of the doors have been closed.


Hopd this help (remember comment and rated this).

May 04, 2010 | 2005 Chevrolet Cobalt

2 Answers

Keyless entry remote quit working. Just purchased new battery. Now Spare remote does not work either.


Transmitter Programming Notes Transmitter Programming

  1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
  2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
  3. Repeat step #2 for each additional keyless entry transmitter.
  4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

Jun 17, 2009 | 2000 GMC Sierra

1 Answer

How do i program remote keyless entry? I replaced the battery and keyless entry quit working,


You don't normally program a keyless entry, that's done for you by the technicians that install that. If the replaced battery doesn't solve the problem, take the battery and the remote to the techies that installed it.

Mar 27, 2009 | 2003 Chevrolet Monte Carlo

2 Answers

My remote for the keyless entry does not work.


does trunk button work? panic button?
here's 2003 info:


  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter.
  • Driver door module (DDM).
  • Go To Pinpoint Test G .

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
GENERAL PROCEDURES Remote Transmitter Programming
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------------------
report back

Mar 22, 2009 | 2004 Lincoln LS

3 Answers

Keyless entry for 05 Kia Sportage


i have a kia optima my keyless quit working to.I took it back to the dealer and the said it was common on a lot of kia models.They replaced the module for the keyless remote,that seams to have fixed it.

Mar 17, 2009 | 2004 Kia Optima

1 Answer

Lincoln LS keyless entry problem


you half to take it to a ford dealer and have the remote reprogramed to the car.

Feb 16, 2009 | 2001 Lincoln LS

1 Answer

There is no sound from the horn when I press on the horn in the steering column or when I hit the panic button on the keyless entry remote. I have checked the fuse and it is good, also have checked the...


my keyless entry has been working great we went on vacation. it quit working i cheched the fuses and the battery in the remote everything is fine just does not work anymore

Jul 22, 2008 | 2005 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...