Question about Ford Ranger

Open Question

Torque settings for 2007 ford ranger 2.5 tdci

I need torque settings for 2007 ford ranger 2.5 tdci as well as intake and exhaust settings. the vehicle was overheating and two rocker arms broke. I had these replaced but then two more rockers are broken thereby creating a 'knock' sound. What could be the problem? I need help

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 124 Answers

SOURCE: I am changing intake gaskets

89 inch pounds then 30 degrees. make sure the push rods get put back in same place they came out they are different lengths. If you ever do another one of these buy the tool for the rocker arms and you will not have to remove them or the rear valve cover. please rate

Posted on Dec 27, 2008

  • 1 Answer

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Posted on Dec 02, 2008

  • 2692 Answers

SOURCE: Torque Specs

Torque: 210 @ 4000 rpm

Posted on Dec 22, 2008

  • 1 Answer

SOURCE: need torque specs

Valve Rocker Arm Bolt 19 N·m + 30° (14 lb ft+ 30°)
A GM dealer shows me another source, which says 32 Nm (24 lb-ft). Not sure which one is right but they screwed up my car.

Posted on Mar 17, 2009

sirgabe51
  • 66 Answers

SOURCE: I have 4.9L6 need torque specs for cylinder head

for cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.


e023442.jpg

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Gap for tappets for 2.5 tdci engine


2.5 tdci knock - Ranger-Forums - The Ultimate Ford Ranger Resource

www.ranger-forums.com/2-3l-2-5l-i4-tech.../2-5-tdci-knock-143638/
Sep 20, 2014 - Hello I've just bought a 2007 tdci 2.5 ranger and it has a constant knock, I don't think it's bottom end, I'm hoping it's a tappet as the nock is. ... Never work on that engine but on other engines if you disconnect 1 fuel injector ... off and adjusted them to the correct gap also made no difference, I'm at a loss now ...

Aug 03, 2015 | Ford Ranger Cars & Trucks

2 Answers

How to install rocker arms on a Pontiac grand am 2001 V-6


Hi there:

Rocker Arms & Pushrods


Removal & Installation

3.1L & 3.4L Engines
Left Side

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system to a level below the coolant pipe on the front of the engine.
  3. Remove or disconnect the following:
    NOTEKeep the pushrods in order. Intake pushrods are 5 3 / 4 inches long and exhaust pushrods are 6 inches long.


    Negative battery cableSpark plug wiresHeater bypass pipePositive Crankcase Ventilation (PCV) valve and hoseRocker arm cover


    Rocker arms and pushrods

To install:

  1. Lubricate all the valvetrain components with engine oil.
  2. Install or connect the following:

    Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm).Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).PCV valve and hoseHeater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).Spark plug wiresNegative battery cable
  3. Refill the cooling system.
  4. Start the vehicle and verify no leaks.




3_4_2013_5_26_48_pm.gif


Right Side
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    NOTEKeep the pushrods in order. Intake pushrods are 5 3 / 4 inches long and exhaust pushrods are 6 inches long.


    Negative battery cableAlternator bracket on 2005 modelsSpark plug wires from the spark plugs and the upper intake plenum wire retainerPower brake booster vacuum pipe from the intake plenumAccessory drive beltAlternator, if necessaryIgnition coil assembly and Evaporative Emissions (EVAP) canister purge solenoid as an assemblyRocker arm cover


    Rocker arms and pushrods

To install:

  1. Lubricate all the valvetrain components with engine oil.
  2. Install or connect the following:

    Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm) plus an additional 30 degree turn.Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).Ignition coil and EVAP solenoid assemblyAlternator, if removed. Torque the bolts to 37 ft. lbs. (50 Nm).Accessory drive beltPower brake booster vacuum pipe to the plenumSpark plug wiresNegative battery cable
  3. Start the vehicle and verify no leaks.





Hope this helps.

Mar 04, 2013 | Cars & Trucks

1 Answer

On the 3.1L engine in the 1999 Chevy Malibu, I need to install the intake and exhaust rocker arm and push roods.


The exhaust push rods are the shorter of the two, the intakes of course are longer. The rocker arms should have been keep in order removed but they are the same for intake and exhaust valves. Torque to the rocker arms to 13 foot pounds.

Sep 17, 2012 | Cars & Trucks

2 Answers

Valve lash procedure


i need to know how to adjust the valves on 02 pont sunfire

Nov 20, 2011 | 1991 Chevrolet K1500

1 Answer

Looking for torque setting for 2002 ford ranger with a 3l rocker arms


The bolt torque spec for the 3.0 Vulcan V6 rocker arms is 18-26 foot lbs, I always set it in the middle, so 22 foot lbs will do just fine. If I helped please rate me for fixya.com
Thanks

Oct 25, 2011 | 2002 Ford Ranger Regular Cab

1 Answer

Need head bolt torqe for 3100 and should bolts be dry


The bolts should have thread lock on them when installing, and the torque is done in 2 steps. 33 ft lbs. and then 90 deg. after that on the second pass. 3.1L Engine CAUTION
Observe all applicable safety precautions when working around fuel. Whenever servicing the fuel system, always work in a well ventilated area. Do not allow fuel spray or vapors to come in contact with a spark or open flame. Keep a dry chemical fire extinguisher near the work area. Always keep fuel in a container specifically designed for fuel storage; also, always properly seal fuel containers to avoid the possibility of fire or explosion. LEFT SIDE (FRONT)
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system into a suitable container.
  4. Disconnect the top half of the air cleaner assembly, then remove the throttle body air inlet duct.
  5. Remove the exhaust crossover pipe heat shield and crossover pipe.
  6. Disconnect the spark plug wires from spark plugs and looms then route the wires out of the way.
  7. Remove the rocker arm (valve) covers.
  8. Remove upper intake plenum and lower intake manifold.
  9. Remove the left side exhaust manifold.
  10. Remove oil level indicator tube. NOTE: When removing the valve train components they must be kept in order for installation in the same locations they were removed from.
  11. Remove rocker arms nut, rocker arms, balls and pushrods.
  12. Unfasten the cylinder head bolts evenly, then remove the cylinder head from the engine compartment. Remove and discard the gasket. To install:
  13. Clean all the gasket surfaces completely. Clean the threads on the cylinder head bolts and block threads.
  14. Place the cylinder head gasket in position over the dowel pins on the cylinder block so the words THIS SIDE UP are showing.
  15. Coat the bolt threads lightly with sealer, then install finger-tight.
  16. Tighten the cylinder head bolts in sequence to 33 ft. lbs. (45 Nm). With all the bolts tightened make a second pass tightening all the bolts an additional 90°.
  17. Install the pushrods, rocker arms, balls and rocker arm nuts in their proper locations. Tighten the rocker arm nuts to 18 ft. lbs. (25 Nm).
  18. Install the lower intake manifold and upper intake plenum.
  19. Install the rocker arm (valve) covers.
  20. Install the oil level indicator tube. Insert the dipstick.
  21. Connect the spark plug wires to spark plugs and looms.
  22. Install the left side exhaust manifold.
  23. Install the exhaust crossover pipe and heat shield.
  24. Refill the cooling system.
  25. Install the top half of the air cleaner assembly and the throttle body air inlet duct.
  26. Connect negative battery cable.
  27. Start vehicle and verify that there are no leaks. Fig. 20: Cylinder head mounting and bolt tightening sequence - 3.1L engine 86883134.gif
RIGHT CYLINDER HEAD (REAR) CAUTION
Fuel Injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove the top half of the air cleaner assembly and remove the throttle body air inlet duct.
  5. Remove the exhaust crossover pipe heat shield and crossover pipe.
  6. Raise and safely support the vehicle.
  7. Detach the Oxygen (O2) sensor connector.
  8. Disconnect the exhaust pipe from the exhaust manifold.
  9. Remove the right side exhaust manifold.
  10. Carefully lower the vehicle.
  11. Disconnect the spark plug wires from spark plugs and wire looms and route the wires out of the way.
  12. Remove the rocker arm (valve) covers.
  13. Remove upper intake plenum and lower intake manifold. NOTE: When removing the valve train components they must be kept in order for installation in the same locations they were removed from.
  14. Remove rocker arms nut, rocker arms, balls and pushrods.
  15. Unfasten the cylinder head bolts evenly, then remove the cylinder head from the engine compartment. Remove and discard the gasket. To Install:
  16. Clean all the gasket surfaces completely. Clean the threads on the cylinder head bolts and block threads.
  17. Place the cylinder head gasket in position over the dowel pins on the cylinder block so the words THIS SIDE UP showing.
  18. Coat the bolt threads lightly with sealer, then install finger-tight.
  19. Tighten the cylinder head bolts in sequence to 33 ft. lbs. (45 Nm). With all the bolts tightened make a second pass tightening all the bolts an additional 90°.
  20. Install the pushrods loosely retained with the rocker arm assemblies. Make sure all pushrods are in the correct locations. Coat the ends of the pushrods with prelube. The intake rods are marked yellow and are 5 3?4 inch long. The exhaust pushrods are marked green and 6 inches long. balls and rocker arm nuts. Tighten the rocker arm nuts to 18 ft. lbs. (25 Nm).
  21. Install the lower intake manifold and upper intake plenum.
  22. Install the rocker arm (valve) covers.
  23. Connect the spark plug wires to spark plugs and wire looms.
  24. Raise and safely support the vehicle.
  25. Install the exhaust manifold.
  26. Connect the exhaust pipe to the exhaust manifold.
  27. Carefully lower the vehicle.
  28. Connect the Oxygen (O2) sensor wiring.
  29. Install the exhaust crossover pipe and heat shield.
  30. Refill the cooling system.
  31. Install the top half of the air cleaner assembly and the throttle body air inlet duct.
  32. Connect negative battery cable.
  33. Start vehicle and verify that there are no leaks.
prev.gif next.gif

Feb 04, 2011 | 1997 Oldsmobile Achieva

1 Answer

Blown head gaskit need to remove head and replace with new ong


2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • Accessory drive belt
    • Air cleaner outlet duct
    • Engine mount
    • Intake manifold
    • Exhaust manifold
    • Engine Coolant Temperature (ECT) sensor electrical connector
    • Power steering pump
    • Radiator inlet pipe
    • Spark plug wires
    • Rocker arm cover

    NOTE Whenever valve train components are removed, keep them in order for installation purposes.

    • Rocker arms and pushrods
    • Lifters
    • Alternator rear brace and the alternator
    • Power steering pump
    • Radiator inlet pipe
    • Ignition coil assembly
    • Accessory bracket
    • Spark plug wires
    • Cylinder head bolts

    WARNING Two sizes of bolts are used; note the location of each.

    • Cylinder head
  5. Inspect the cylinder head and block surface for cracks, nicks, heavy scratches and flatness.
b9d2546.gif
Cylinder head torquing sequence—2.2L (VIN 4) engine

  1. Install or connect the following:
    • Cylinder head with a new gasket and new cylinder head bolts. Torque the long bolts, in sequence to 46 ft. lbs. (63 Nm) and the short bolts to 43 ft. lbs. (58 Nm) plus an additional 90 degree turn on all the bolts.
    • Lifters
    • Pushrods and rocker arms. Torque nuts to 22 ft. lbs. (30 Nm).
    • Rocker arm cover. Torque the bolts to 89 inch lbs. (10 Nm).
    • Spark plug wires
    • Accessory bracket
    • Ignition coil assembly
    • Radiator inlet pipe
    • Power steering pump. Torque the bolts to 22 ft. lbs. (30 Nm).
    • ECT sensor electrical connector
    • Exhaust manifold. Torque the nuts to 118 inch lbs. (13 Nm).
    • Alternator. Torque the bolts to 37 ft. lbs. (50 Nm).
    • Intake manifold. Torque the bolts to 17 ft. lbs. (24 Nm).
    • Engine mount. Torque the bolts to 55 ft. lbs. (75 Nm).
    • Air cleaner outlet duct
    • Accessory drive belt
    • Negative battery cable
  2. Refill and bleed the cooling system.
  3. Start the vehicle and inspect for leaks.

Oct 08, 2009 | 2000 Chevrolet Cavalier

2 Answers

Where is the head gasket in a 1990 buick skylark and how do you knopw if its bad?


Gasket is between cylinder head and engine block. If u have oil in the coolant or vice versa, or overheating then u most likely have a bad head gasket

Dec 29, 2008 | Buick Skylark Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...