Question about Cars & Trucks

1 Answer

I have a Brilliant 16TCDL gas fire without a user manual, I wanted to get the fire serviced but it cannot be done without a user manual. I have contacted Brilliant but they don't keep manuals for

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,077 Answers

You have this posted in the Car and Truck product category. If you want the right expert to read this please post it in the correct category. Thanks

Posted on Feb 14, 2012

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 14036 Answers

SOURCE: car died while driving, cranks, but won't fire, no communication with scan tool as far as engine or transmission. It will communicate with body.

did you say scanner not powering up or you not getting any code.because if engine not firing a faulty crankshaft position sensor or ignition module will cause no spark conditions.also check 20 amp ignition fuse to ignition coils and ignition module,check ignition battery feed 10 amp fuse to the pcm.check at the 16 dlc terminal at top ground terminal 4 that would be fourth terminal top from left to right.and check bottom far right terminal 16 see if you getting getting battery power.if fuse all good no power at terminal 16 your pcm could be getting poor ground contact or problem in the pcm thats not a home fix dealership has to run diagnostic scan test look for pcm fault or wiring fault.

Posted on Nov 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How hard is it to replace the blend door actuator for the vent, defrost, floor, its not swapping vents it was clicking but now


On some cars this requires removal of the entire dash. Brilliant design, no? Buy shop manual, or better still, hire this done.

Oct 07, 2015 | Cars & Trucks

1 Answer

What happens at 97,000 mile check up


You may be able to get a user manual at Toyota's website or ask for one at you local dealer. Or, if you've ever had the vehicle service, the facility that serviced it should have a manual with the info you want.

Jun 06, 2013 | 2005 Toyota Highlander

1 Answer

Van wont start, just turns over, wont catch.


I had the same problem and had it towed to the local dodge dealer. The problem was that it needed a new fuel pump. It's a fairly big job since the pump is located in the gas tank (what a brilliant idea). I had it done and it cost nearly $700. Still love the car!

Sep 26, 2012 | 1995 Dodge Grand Caravan

1 Answer

Need location of fuel filter and how to change.


The fuel filter is located on the fire wall in the engine
compartment. You may not want to attempt this.
Should be done when engine is cold, also have to
relieve fuel system pressure, place shop rags around
filter for gasoline spillage and will be dealing with bolts
on gas line. It can be done, but I think a repair manual
(Haynes) is a must.

Jan 25, 2011 | 1999 Honda CR-V

1 Answer

98 Rodeo left bank not firing


check and see if it has a seperate ground for each side sound like a bad ground

Aug 17, 2009 | 1999 Isuzu Rodeo

1 Answer

Misfires, sticking 2-3 selonoid in tranny, and sluggish to start


I would make sure the engine is properly tuned. The miss fire condition could be making the transmission run poorly. Once the miss fire is repaired , then recheck the transmission.

The miss fire can be caused by several things after the tune up is done. The ignition coil, the fuel pump and filter , the computer , injectors do carbon up.

So when getting the tune up ask to have the injector cleaning done. The injection cleaner for the engine is from the dealer . They have a special cleaner . This is a common repair per Chevy to have the injection service done.

Good luck

Mar 22, 2009 | 1999 Chevrolet K1500

1 Answer

I HAVE GMC ENVOY XL 2005 BUT I NOT HAVE USER MANUAL GUID


take it up to autozone and tell them you want a trouble code done, it will tell you exactly what is wrong, the service is free.

Nov 18, 2008 | 2004 GMC Envoy

2 Answers

Parts Wanted (ECU 5K)


You should contact Mazda Authorized Service Center for this.

Jul 12, 2008 | 1994 Mazda 323

1 Answer

Service Engine Soon


make sure to check the firing order, that means every plug wire has to go to a specific spark plug, if you unplug all or more than one plug wire at same time, you might mix it, and that should be all your problem just get a firing order specifications and have it done.

Jun 16, 2008 | 2002 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

426 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...